Reviews
Unfortunately, the length was good but the shaking while driving was not calculated.
Since the Meter on MT-07 is directly above the Handlebar, I wanted to place my phone and Car Play Monitor on the upper side of the Meter, so I chose this product with a longer bar length.
The length was good, but the Mirror mount bracket was not able to support the weight of the phone and CarPlay Monitor due to the Bolt1 pc fastening, causing it to shake considerably while riding. As a result, I moved the length of the bar to a shorter length so that it would be closer to the fulcrum. Since it still shakes, I am planning to change to a Bolt2-Bolt Type of Master CylinderClamp from DAYTONA and others.
View detail
It was a little long for me.
[How is it used?
After six months of hanghang and Restore&Custom work on the LITTLE CUB, I thought I'd get comfortable with the next stage of the project. First, we need an external power source. I started looking for a USB power supply, but realized that there was no place to install them, so I looked for a Mount Bar in Webike's product introduction section and bought a Multi Bar from Made by HURRICANE, which had a safe design.
How did you like it?
Although I knew it existed until now Messy around the Handlebar. The Mount bar had never been used before because I had the impression that it was too heavy.
The fact that I had a safe length and design for my first Mount bar purchase and I was a teenager. Separate handle (Handlebar of Separate type)". Speaking of Other Brand Products of "HURRICANE It was an Image that I was not surprised to see. Finally, I too will buy HURRICANE products." I bought the Multi Bar at Tension...but the bar was a little too long for my use.
Please don't get me wrong, the product itself was a good product with good rigidity, but for my personal use, I would have preferred a shorter length, so after much thought, I replaced it with a Mount bar made by another company.
We wanted to use a Short Type Mount Bar to make it as Refreshing as possible, since we only need to be able to fix the USB power supply and Smartphone Holder.
How did it compare to other products?
If it is a MAJOR Manufacturer's product. "A damned glitchy piece of junk." I don't think there are any.
Before you buy Which car? of Which part? and there you want to install it in What do you want to install?" I think that Risk can be reduced if you take into account the following before making a purchase.
[Points to note]
This product is a type that is attached to the Mirror Holder by fastening it to the Mirror Holder, so it is easy to set the quantity to a position that is easy to use.:Once set, please tighten and secure each part firmly, otherwise you will be in a hurry if it loosens while driving... (This is a testimonial.)
Other items that would be helpful
The deciding factor in the purchase
As I mentioned above, I didn't even understand the difference between the Mount bar and I didn't think it through. HURRICANE Products I bought this product only because it was a very solid product with no fault of this product over and over again.
【Included Parts:presence or absence】.
Bracket for connecting Mount Bar Body and Mirror Holder, 2 Washers and Spring washerQuantity:1pc. and Nut included.
[ITEMS TO BUY TOGETHER
Products to be installed on Mount bar.
If you purchase the products you want to install at the same time, such as a power supply outlet, Smartphone Holder, Drink Holder, Camera Mounting Holders, etc., you can proceed with the work at a stretch.
Opinions and requests to Manufacturer.
It resonates with my father's generation. "HURRICANE BrandName, we look forward to continuing to serve you with a variety of custom parts at affordable prices.
View detail
Bolt hole
Since the Bolt hole position was different by about 5mm and could not be installed, it was installed by making a long hole with File. Forced installation may damage the screw holes. View detail
Fits: KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI Ninja 1000SX
Installation is fine, but ….
The Handlebar Mount Bracket was installed without any problems.
However, because my body is not large enough, the Handlebar was squeezed inward, making it impossible to mount.
I would suggest you to match the body to the car body and then choose other PARTS.
View detail
Fits: KAWASAKI Ninja 250, KAWASAKI Ninja 400 (2014-)
The product was exactly as shown in the picture and there were no problems.
I installed it on my ninja250. It was easy to install and I am using it without any problems.
I installed the Smartphone Holder that I originally had. I am touring comfortably.
View detail
Fits: HONDA CB250R, HONDA CB250R, HONDA CBR250R (2011-), HONDA CBR250R (2011-), HONDA CBR250RR (MC22), HONDA CBR250RR (MC22), HONDA CBR250RR (MC22), HONDA CBR250RR (MC22), HONDA CBR250RR (MC22), HONDA CBR400R (2013-), HONDA CBR600RR, HONDA CBR600RR, HONDA NSR250R, YAMAHA YZF-R25, HONDA CB300R, HONDA CBR500R, YAMAHA YZF-R3
It didn't come with just this.
This and the Mount Kit are required.
In total, I think the cosmetics are nowhere near as good as the Gold amount.
View detail
I had no choice but to buy it…
I purchased this product in order to attach the company's Smartphone Holder (KDR-M14C). The reason is that the Mirror mount that comes with the Smartphone HolderBody has a plastic plastic "Thickness The included parts:were unbelievably thick (about 4mm/see image) and could not be installed after all. I wonder if everyone can install Mirror with this. Even if it is made thicker to prevent vibration, it is too thick.
I bought this product separately, but it shakes a lot when idling. The product of another manufacturer used in the previous vehicle was not so bad. I think this depends on the vehicle (idling vibration), so I can't say for sure. That is a little bit Minus. I am satisfied with the rest, and I think that if I adjust the angle of the bracket and the bar well, I can adjust the position of the Large body to my liking.
View detail
… It's subtle.
The dimensions, machining accuracy, and practicality are solid, but … to be honest. Parenthesis bad." It is. (Personal opinion.)
I mounted the clock etc. for now, but it is far from the Bridge-like Image of the Off car, to be honest. I'm fucked." The feeling is strong.
Mount bar for low-cost use." If you are looking for a good product, Camouflage may be a good product for you.
View detail
Made by stable DAYTONA
Easy to install, good material quality. View detail
Better visibility, but also vibration...
The phone is positioned at the top of the Screen, making it easier to see.
However, it is harder to see than when I had the Smartphone Holder on the Handlebar before because it shakes with vibrations while driving.
The screen is fixed by a rubber bush, so I guess it can't be helped, but it might have been a little bit of a mistake...
View detail
A necessity if you use Navigation on your phone.
The instruction manual was inadequate and I had to think a lot before I could install it.
It is long enough to attach at least 3 different types.
View detail
Be careful with thick Mirror at the root.
It's light and looks weak at first glance, but it's strong enough that it won't deflect even if you put a lot of pressure on it.
However, it didn't stick with my Mirror because it was incompatible with it, so please refer to it.
Ideas is good because you can turn it over and it can go either way.
View detail
Things are good, but expensive.
If you have a Hexagonal Wrench, even a beginner can install it.
It's an Exclusive Design, so it's easy to use, but it's expensive.
Also, the included Bolt rusted quickly.
The Multi Bar of De*tona is Matte tone, but this one is glossy.
View detail
Fits: HONDA VTR250, YAMAHA MT03, HONDA Forza300, HONDA CB500X, HONDA CB500F, HONDA CB150R, YAMAHA XSR900, YAMAHA MT-25, YAMAHA MT-09, SUZUKI Gixxer 150., SUZUKI Gixxer 250, SUZUKI DL1000 V-STROM250, HONDA HORNET250, HONDA FORZA Si, HONDA FORZA Si, HONDA JADE, HONDA glom, HONDA CROSSCUB110, HONDA APE 50, HONDA XR100MOTARD
Best position
[How is it used?
Used for Navigation and fixing your phone when touring.
Was the one you received as per Image?
As per Image.
Was the installation difficult?
You only need to remove the Screw and install it, so if you have Hexagonal Wrench, it's a piece of cake. However, be careful of the overtorque of Screw tightening.
How was your experience with it?
You can choose 2Pattern with the bar at the front or at the back in the direction of installation.
[Included Parts:were they on?
Included Parts:Bolt and collar are all that is needed for a complete installation.
[Was there anything that disappointed you?
The surface of the bar is soft. The surface of the bar is soft (?), so once you install it tightly, it will leave a mark.
If you are worried about it, you might want to wrap it around the anti-scratch Seat.
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
expensive
This is a normal Mount bar.
The downside is that it's expensive.
View detail
Fits: HONDA CB300R, HONDA CBR500R, HONDA NSR250R, HONDA CBR650R, HONDA CBR600RR, HONDA CBR600RR, HONDA CBR400R (2013-), HONDA CBR250RR (MC22), HONDA CBR400R, HONDA CBR250RR (MC22), HONDA CBR250RR (MC22), HONDA CBR250RR (MC22), HONDA CBR250RR (MC22), HONDA CB250R, HONDA CBR250R (2011-), HONDA CBR250R (2011-), HONDA CB250R
Installed on CBR650R
Installed to put a Smartphone Mount on my CBR650R.
If you want to install this product on your CBR650R, you need to use two M16 washers on the bolt. (I'll give you a reference in the picture)
I've been using it for about four months now, and in terms of convenience, it's perfect!
Even with the phone mount, there is still a lot of space, so you can add USB or something else.
If I had to pick a demerit it would be that it looks a bit rugged, and I don't like the idea of having a protruding part on a sports bike lol.
But still, I can't beat the convenience and I've been using it for a long time, so it's really a Recommendation!
And it's cheap lol.
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
usually
It is a nondescript Mount bar.
It would be nice if it was a little cheaper.
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
A little high
This is a normal Mount bar.
I wish the price was a little lower.
View detail
Simple design
I bought this to install Navigation.
It is very easy to install as it only needs to be tightened with Mirror.
The adjustment mechanism is simple, the bar rotates around the bracket.
The angle is fixed, so Navigation is a little tilted, but it's acceptable.
View detail
Fits: YAMAHA BirdCity, YAMAHA BirdCity, YAMAHA BirdCity, YAMAHA BirdCity, YAMAHA BirdCity, YAMAHA BirdCity, YAMAHA BirdCity, YAMAHA BirdCity, YAMAHA BirdCity 155, YAMAHA BirdCity 155, YAMAHA BirdCity 155, YAMAHA BirdCity 155, YAMAHA Tricity155
Fewer interference reports even when installing external screens.
The mount type parts that can be installed on BirdCity are
1.Type with Mount bar near the Handle using Mirror mounting hole.
2.Type with Mount bar on the top side of Meter using Screen mounting part.
There are two types, both with their own advantages and disadvantages
For Type 1, the Bracket is placed in the Mirror mounting area and the Mount bar is attached to it.
The advantage is the high degree of freedom of the mounting position of Option and easy to avoid the contact of Screenetc.
If you plan to install a drink holder, definitely this one!
Type 2 uses the Screen mounting area and attaches the Mount bar from there to the Meter.
The advantage is that the Mount bar is positioned above the Meter, so the mounted object naturally comes into view.
On the other hand, if the object to be mounted is a large size, the meter relation (Including Indicator) Visibility of the
In addition, since it is made on the premise of NORMAL, there is a possibility of interfering with Long Screen and external Screen.
Fortunately, the Mount of this KIJIMA is purchased because there seems to be almost no interference report.
Long Screen of WorldWalk can be installed without a problem.
View detail