Reviews
Good multi bar!!
It's a really good product. Both the finish and the design are excellent. I bought the multiba twice. Thank you for your prompt delivery. I recommend this product to others, too View detail
Fits: HONDA CRF250L, HONDA 400X, HONDA GB350, HONDA GB350S, HONDA CB400F, HONDA NC700S, HONDA NC700X, HONDA NC750S, HONDA NC750S, HONDA NC750X, HONDA NC750X, HONDA NC750X, YAMAHA XSR155, YAMAHA XSR700, YAMAHA SR400, YAMAHA SR400, SUZUKI Gixxer 250, SUZUKI V-STROM250, SUZUKI V-STROM250
suitable for gixxer 250
About quality and texture : handlebar material is solid About the feeling of use : solidly supports my handphone and action camera Products to buy together : you will need accessory mounts for your phone or action cameras Difficulty of installation : easy. just remove old bolts and install bolts provided Cost performance and comparison with other products : higher price but worth the good quality About shipping and packaging : fast shipment and good packaging Any concerns, cautions, or advice when purchasing : this works only on gixxer 250 View detail
Good multi bar!
It's a really good product. Both the finish and the design are excellent. Thank you for your prompt delivery. I recommend this product to others, too View detail
Large may be strange.
LargeChangeIt was a good product. I will use your service in the future. Thank you very much. View detail
Simple and good.
I had a long Gadget Bar on my previous Motorcycle that straddled another Manufacturer's Bridge, but I had just added a Smartphone Holder near the Left Side.
This time I bought this one.
The simple is best。
Reasonable price.
View detail
For Smartphone Holder installation.
CB250R Handlebar was replaced and the aperture angle became too tight.
Smartphone Holder on Handlebar
I introduced it because it turns inward quite a bit.
Clamp Bar length is 90mm (excluding Cap)
The height is from the Center of the Pipe to the Mirror mounting point.
It is about 50mm to the top edge of the bracket.
The bar length is 10mm shorter than that of HURRICANE.
I was looking for something short, so it is Exactly for me.
Bracket is turned upside down from de Fault.
It's a matter of feeling, but if you put it in this position with the Defferential Gearo
The bracket risers will be exposed to the wind.
Both top and bottom are drilled for M10.
Also, the Cap on the bar is loose, so I used Cellophane tape.
It is tight and inserted.
If you don't do this, the Level will fall down due to vibration.
Smartphone Holder was installed on Best position.
View detail
For cell phones and recharging.
Product Name
Multi Bar
Item Number
EI533EX4A1
Vehicles
NINJA400 (2BL-EX400G)
Number of man-hours
About 10 minutes
Required Tools
Torque wrench, hexagonal socket
Why did you choose this product?
I decided to buy this because I need it to charge my cell phone and cell phone when I ride my Motorcycle. I use Ram Mount and DAYTONA Charger, so I chose this one because it was the cheapest Multi Bar.
Was the one you received as per Image?
It was just like the Image, it came with Screws, Body and Instruction Manual.
Was the installation difficult?
It was easy to remove the two Screws and screw the Body back on again.
How was your experience with it?
The black paint is perfect with no gaps or misaligned screw holes due to the Exclusive Design. I installed Sugar Socket, USB, and Ram Mount, but there is still enough width to mount a gopro or other device.
[Included Parts:were they on?
Instruction Manual, screws, and Body were all available.
[Was there anything that disappointed you?
Nothing in particular. I would be happy if the price was a little lower.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Refreshing around the Handlebar and improved visibility of the Smartphone
There is not much room around the handlebar of the REBEL250, and it is not possible to secure a place to install a smartphone or other device. We had been using KIJIMA's Multi Bar, but it was too high, so we decided to use Endurance's Multi Bar to make it a little lower and to make it easier to install.
I thought the work would be Large strange since the Meter would be relocated, but in fact it was not so difficult and the work could be completed in about 30 minutes. The Endurance Meter visor can also be installed at the same time.
By relocating the Meter, the Meter is no longer hidden by Smartphones and other devices.
On the other hand, it is difficult to install the Smartphone Holder unless it is a Compact one.
In this case, we are using a Compact with KaEdia's recharging function.
Using a home-made Bracket, DriveRecorder- was also able to be combined with Refreshing.
Others have been able to shoot with the insta360 RS attached, etc.
Recommended for those who want to add various things around the Handlebar in a Simple and Compact way.
View detail
This is soooo good.
I think it is a must-have item for Smartphone Holder installation.
I was wondering how to attach a Smartphone Holder to a Motorcycle with Separate handle, so this is a breakthrough.
There are many ways to attach it, but this product caught my eye quickly.
Installation was easy, so I am glad I purchased this one without any problems.
The Smartphone Holder is also in a good position.
View detail
As if it were an OEM product.
FORZA required the installation of a Multi Bar because the Handlebar was not exposed.
Initially, we attempted to add an inexpensive Universal-type Multi Bar that would be installed using the Mirror hole.
However, when the Handlebar was turned off, it came in contact with the Screenetc. and was not oriented properly, so we decided to purchase this product.
This product is Exclusive Design and does not violate the design of MotorcycleBody, thus satisfying the Large change.
The price is a bit high, but overall I am satisfied with the Large change.
IMPRESSION DETAILS
0Package
Very careful packaging with SpongeCushion as well.
0 Product quality
No welding or processing problems
Good paint job.
0 Installation
Easy even for amateurs without any problems
◯ Usability
It is good that the location study seems to be well done.
I personally think it's a good position, out of the way.
Processing of 0Cover
Endurance sells a special modified Cover, but I have modified the Body.
The instruction manual includes instructions for processing the body (size of the notch is indicated, etc.), and processing is possible using a nipper, cutter, and sandpaper.
I think it's better to start out small and then cut around the edges.
Because it was cut by Nipper, there is a white mark on the CoverBody, but it is not noticeable and I don't mind it.
Related to 0OthersCustom
ETCAntennas are installed in the Handlebar Center Cover with no problems.
Wiring with DAYTONAUSBCable and ETCAntennasCable attached to Multi Bar.
The product was installed by drilling a hole in the MotorcycleBody (plastic), which is not too difficult to process.
In this case, we took care to drill the smallest possible hole, as drilling too large a hole can cause strength problems.
Recommended Point
The large size and length of the bar is the smallest necessary, and it is a functional product that does not destroy the design of FORZABody.
View detail
Looks rigid.
We hesitated with DAYTONA, but chose this one, which looks rigid.
If the Smartphone Holder is attached to the bottom, it is too far forward, and if it is attached to the front, the Meter is not visible.
I am thinking of extending this and attaching a Bar Holder to it to make it an easy-to-see Position.
View detail
If you want to Refreshing around Handlebar!
I was looking for something good for mirror installation because of the clutter, and I found this product. It is easy to install, and I use it with TaBrett as Navigation, and it does not cover the Meter, so it looks great! View detail
To ride Motorcycle for a day longer!
I really wanted to go a little higher, but Motorcycle these days is Wire, Cableetc.. I had no choice but to reach for this product because I could not extend it. The texture is quite good and the feel is better than I expected. The installation was just as described in the reviews. I think it is better to replace the entire handlebar for parenthesis, but I want to ride my motorcycle for a day longer than to hurt my body with unreasonable posture, so I think it is possible with good cost performance! View detail
No complaints
Compact and easy to install without interfering with driving View detail
That's enough.
If you only need a Smartphone Holder, this product is suitable for you, not something that straddles the Fork. Torque wrench may be necessary, but only two Rose Screws are needed. View detail
late delivery
Delivery date is 3 days later than when the order was placed.
There is also no CanCell button listed in the Cancellation method.
I will never buy from this Site again.
View detail
2019 monkey125
2019 monkey125(jb02) can be installed. It's firm. i will hang a kind of plastic bag on the helmet hook. it's so versatile. View detail
If you want to put a couple of these on your bar, I recommend it.
If you want to attach more than one USB or smartphone holder around the handlebar, you can do so.
The Multi Bar is useful, but the Large Bar and the one in the center of the Handlebar are not.
It was getting in the way when I was driving, so I replaced it with this one.
If you have up to two things to attach to the bar, I recommend Left only.
View detail
Fits: HONDA Forza Si, HONDA GROM, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER BOL D'OR, HONDA CB400 SUPER BOL D'OR, HONDA CB400 SUPER FOUR, HONDA FORZA(MF10), HONDA ZOOMERX, HONDA FORZA(MF08), HONDA VTR-F, HONDA VTR250, HONDA PCX125, HONDA PCX150, HONDA PCX150, HONDA PCX125, HONDA PCX125, HONDA CB1100, HONDA Forza300, HONDA CB1300 SUPER BOL D'OR, HONDA CB1300 Super Four
Hide the holes in the Handlebar Post with the Separate Handle.
Because I put a separate handle on it, the handlebar post part is noticeable and I put it on to hide it.
Of course, it's not just for hiding, but also for mounting the smart phone mount and USB Charger, so I can use it effectively.
View detail
Fits: YAMAHA NMAX, YAMAHA NMAX, YAMAHA NMAX, YAMAHA NMAX155, YAMAHA NMAX155
Material without worry of rust : Stainless Steel.
Used around the time when I was on NAX 155.
Material without rust concern in Simple : Stainless Steel, this item only.
Once in a while we used Handlebar Post from Company K in another car, but Screw's
Part rusty Rusty Σ (? д ? lll)
Here is the trouble you do not know until you purchase it.
Endeu Rans has a simple shape and is very easy to use.
I was so satisfied that the next Owner feels good when sold
I sold it while wearing it as you can use it.
View detail