Reviews
I lost it, so...
22.I lost my ClampSpacer for 2mm, so I bought Repair Parts.
Only Repair Parts can be purchased for fragile parts, so they can be used for a long time.
View detail
It slips and moves.
Used to attach the Smartphone Holder to the Pipe behind the Screen on the Honda 400X (2019) (with an additional Spacer that comes with the Smartphone Holder).
The size itself is just right, but the hard rubber makes it slippery, and even when the bolt is tightly tightened, it slips and moves. Therefore, I wrapped a thin double-sided tape around the pipe on the body side before installing the bolt, but it is not completely fixed because the outer side of the bolt also slides.
I'm considering replacing the Arm of the Holder with an aluminum spacer only for the type that is tightened with ZETA Bolt.
View detail
Higher height.
I bought this when the Autofocus on my previous iPhone 11Pro Camera broke.
Type VibrationControlDevice to be attached to existing Smartphone Holder3
Just Smartphone Holder3+ IH2100Rigid (25077) The pull-pull mechanism is about 20mm higher than that of the "M" and it shakes more when a smartphone is attached.
I think it can absorb a certain amount of vibration, but the increased height makes it look bad.
If I were to purchase an expensive SMARTMonitoretc. without a phone attached, I would be willing to purchase a used Android phone and use it with TetherRing.
View detail
Fragile Construction, bad quality plastic.
This item looks very promising in the pictures. I really liked the design. In reality It is very weak. It is made of a very weak type of plastic. I have seen cheap phone holders for 7usd that use better material. There are very important parts in this design that should be made of metal, but in this case those are made of thin plastic. From the outside It looks like the body is made of aluminum, but it is just a decorative sheet metal part. If I knew, I would not pay more than 12 usd for this product. On the other hand, the vibration damper doesn't seem to do much. The Handlebar clamp is made of aluminum, but because it is very thin, It looks like it will break if you tighten the screw too much. Don't use this holder on single cylinder bikes, because the damper is not effective enough. Be very careful when installing this product, because It is not made of strong material and it will break If you tighten the screws too much. It looks like It will not last much under the sun either. For 52usd I expected a sturdy well built phone holder. It doesn't look like it was made in japan because of the cheap quality. It is expensive, bulky and flimsy. Next time I will try with SP Connect. View detail
Smartphone cannot be fixed properly
I chose the RAM Mount because I thought it must be a good product since many people use it and a large percentage of Len BarrelMotorcycle models are equipped with it. However, the holding of the X-shaped retainer is not so good, and the Smartphone gradually gapped on a motorcycle with a lot of vibration, and before I knew it, I had to press the SIDE button. Also, when the X-shaped retainer is expanded to hold the Smartphone, it rotates by the amount of the expanded angle and cannot be fixed. It was not easy to use, so I immediately replaced it with another product. View detail
Plastic Parts are too fragile.
Material:Plastic Parts are too fragile.
It is not that the Bolt was tightened with stupid force or that a hard object was slammed against it, but the Plastic snapped off in the order of the claw on the top side that holds the phone in place, the Body side that holds the middle claw in place, and the middle claw, making it unusable within one year of purchase.
The composition of the plastic seems to be hard and brittle, and if the phone is put on and off many times, it seems to get fatigued and go badrill.
I think that if the composition of plastic is changed to something more tenacious, or if it is made of gold, the durability will be improved by a large margin.
I would like to see DAYTONA improve on this.
View detail
Design and quality are good but squishy
I think Vibration is effective, but it is too Kunikunashi and very cumbersome to install and remove the phone. View detail
I don't think this is the best shape.
Quantity the phone:Set will deflect by its weight. To begin with, the BUnit determines the angle between A and C. The BUnit is used to determine the angle between A and C, and the squishy Unit is used to make it difficult to position the BUnit. I wish it was easier to change the angle. If the angle is close to horizontal, you can operate the phone just fine, but if you angle it, you can't operate the phone as you want. For such an expensive product, the feel of the product was terrible. View detail
Mobile Holder
I bought this for navigation on my phone, but I read on the Net that the iPhone's Camera function can break down if it's fixed too tightly…
Not sure whether to use it or not.
View detail
Whether it really works is a mystery.
Vibration is mitigated by sandwiching the Rubber plate between the front and back of the three feet.
It tilts under the weight of the phone, so it may be doubtful how much vibration mitigation capability it actually has if it is tilted by a heavy phone.
The Rubber board is said to be a PARTS that needs to be replaced in about 2 years, but given that the Beacom 5X Speaker is disappearing from bulk sales, it is doubtful how long it will be sold individually.
I hope SYGN HOUSE will not try to sell the same parts even if improved products are released in the future, because it is doubtful that they will be made into the same parts.
If the Rubber plate is hardened, it is still OK, but considering the possibility of deterioration such as tearing off, I wanted the front and back to be connected by a wire to prevent falling off.
Since this is a Type product that mitigates rather than suppresses vibration, it is likely that some Motorcycles will have RPMs that increase the amount of vibration that makes it difficult to see the phone as much as it decreases the amount of microvibration that can be fatal to the phone that is not visible to the human eye.
It can be used for the old product, but it is troublesome because the place to fasten it with Screw adhesive has to be removed.
View detail
Difficulty in moving and fixing the slide part.
I installed it on the handlebar of my Z650, even though the area around the handlebar is narrow and small. It looks nice and simple, but when I installed it on my phone (Xperia5), I had to slide the fixing part, but the slide was not smooth and it was hard to install because it was caught. Also, the lever for fixing is hard and difficult to do. View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
Camera cracks. When the phone is not attached, it is noisy.
[How is it used?
It's a Other Brand ProductHandlebar with separate handle, but I didn't need to use Bracket.
Was the installation difficult?
It is easy to install because it belongs to Hexagon Wrench.
How was your experience with it?
The part that holds the phone is Material:If you don't have your phone on in Plastic, the vibration makes it noisy. I don't want to wear my phone when I'm going for a walk around the neighborhood, but I have to because of this.
When I think that the phone itself absorbs this vibration, it doesn't seem to be so good for the body of the phone, and in fact Camera was broken. (Android)
As a Smartphone Holder, it's affordable, and if you don't make a mistake, your phone won't fall off, but it's not very useful, and the plastic is cheap and makes the Handlebar look tacky.
If you're on a budget, you might want to spend a little more on a good Parenthesis.
[Included Parts:were they on?
It was all there.
Point and hang of installation
If you are using the OEM handlebar on the Ninja 400, you can either run the bracket through the Stem Nut or through the unused screw hole in the clutch lever.
I replaced the handle with SNIPER's Other Brand ProductSeparate handle, which has enough room for the handlebar width, so it can be installed without the bracket.
View detail
The iPhone 11Pro will not fit.
It's my fault for not researching it well and buying it, but it doesn't work for the iPhone 11Pro.
It would have been nice if you had written some examples of models that could be used in the compatibility list.
If you take it out of the Case, you can get in somehow, but it is very inconvenient.
Also, if you put it in a waterproof case with gloves, it is almost impossible to operate.
I have not used it even once after all. When you buy it, I recommend you to buy it after considering the model and the Situation which you use well.
View detail
Not very good.
I used it for about a year and took it off.
First of all, it doesn't move well, and it's frustrating that it doesn't unlock (common individual difference in Chinese Smartphone Holder?).
My acquaintance's was running on Quantity.:Pair (for Left and Right) The inside of the fixed jaw was cracked (maybe the vibration was too severe because of the 250cc high speed driving)
It's cheap, but if it's made in China, it's about the same or cheaper price with charging function.
Most importantly, the possibility of an expensive phone falling out is terrifying.
The feeling of use was also bad, but I used it more patiently than I bought it, but I removed it at the opportunity of the damage of the acquaintance.
The value of the phone is unrelated to the Engine Displacement Volume of the motorcycle, so I think it should be considered.
However, if you put the included (also available at Repair Parts) silicon band on it, you will probably be spared from sudden drops, which is a must for this Smartphone Holder.
It's a popular product, but I personally didn't like it.
View detail
After contacting the distributor
I installed it because of the high ratings on reviews here and there, but it was disappointing.
It's still a Compact, grippy and good looking Holder, but the vibration of the phone when it's running makes it feel like a Quantity:Pair (for Left and Right) to rotate and slant.
I tried it on a sample from a mass merchant to see if there was any difference in quantity:Pair (for Left and Right) It turns into a
I contacted PLOT, the distributor, and I knew that
If you don't have an object in the XGrip, it won't work, but if you have an object in the XGrip, such as a smartphone, it will not work.:Pair (for Left and Right) The answer is that it is the original product spec. that goes around to
What do you think? Do the people who are giving it high marks here and there just not care?
I've never seen a Spec. smartphone holder that rotates and tilts the phone at an angle due to vibration.
I don't think it's possible as a product.
View detail
At first I thought it was a good idea, but then...
It may be individual difference, but the non-slip Silicon of the foundation was not covered firmly, and a part of the bottom aluminum plate was exposed.
It's not a cheap product, and that alone is uncomfortable.
Also, the manufacturer and purchaser were very unresponsive and I ended up using them as is.
On the iPhone 7, if you pinch it with the XGrip, it will interfere with the volume buttons, so the fixing position is limited.
Also a stick that's gripping even when fixed? It is quite wobbly. Even if I try various things, it does not improve.
If this is another individual, I think they sold me a defective product.
I'm disappointed in this product, as it doesn't have a bad reputation.
View detail
Fits: YAMAHA YZF-R3, SUZUKI GSX250R, YAMAHA YZF-R25, KAWASAKI Ninja250SL, HONDA CBR650F, KAWASAKI Ninja250, HONDA CBR250R, HONDA CBR400R, HONDA CBR150R, HONDA CBR500R, YAMAHA YZF-R3
You don't look as pretty as your picture.
When I arrived, I was surprised to see that his appearance is different from the photo. It's dirty, to say the least.
It became the appearance of the picture if it was processed by Paper processing for the first time from File hanging and polished by PIKAL.
The problem with this is that the smartphone holder cannot be tightened with a tool even though it has 10mm screw, and even if it is tightened with a finger, the smartphone holder starts to turn by vibration. It will fall off before it is stolen.
The solution is either machining it so that it can be turned with a tool or gluing it in place that won't come off forever. I'm the former.
I recommend it because it makes effective use of the Mirror Hall, which was only blocked up until now.
processing plan
? I'm going to punch a hole in it like I did.
Because the diameter of the root of the screw has become Large, shave 2 sides with File so that the Spanner may enter.
Firmly grab and turn it with ?Pliers. You need to be prepared to get a lot of scratches on the shaft.
? Solidify with high strength screw lock agent
View detail
I used it and it wasn't much.
Quantity:I bought this set because I thought it would be convenient, but it is not a good idea to use it to attach the mobile phone to the body of the Since the part is not fixed, the angle can change easily. I thought it was a bad idea to use it with it on. If it's another type, you can fasten the body and arm part with bolts. If you're going to use it on a Motorcycle or bike, buy the Type sold at RoseRose. Recommendation. View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
I think it's something like this
I purchased this to install my phone
I was able to install it without any problems, but the part that attaches to the multi-bar The Center of the PenetratingBolt receiver is confusing! There are such things as
I understand the same color Black, but I can change it
View detail
It's not ideal
As a product, I don't have any problems with it at all I feel that the product is a bit cumbersome to put on and take off the phone because it does not come off easily The product is stable and in good condition when installed View detail