Reviews
I kinda like Gui Mick. (Lol)
It is pricey, but there is something about the giMick that is white in the face.
Well, not only is it good looking, but it is also easy to use.
There is a locking mechanism, but you might not want to trust it completely. To be honest, you never know what might happen.
Dropping a phone is the end of the world. Namu! (σpωp) σ
View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
SmartphoneFolder attached to SEROW250
Smartphone Holder is temporarily needed and installed.
The Front was taken out by sand and fell over to the Left once on Asphalt, but the phone did not come off or break and Large was sturdy.
View detail
Freedom from unplugging the charging cord!
[How is it used?
I had been using RamMount as a Smartphone Holder and had no complaints about the body itself, but the only thing that I always found troublesome was connecting the cord for charging.
Since I use my cell phone as a navigation device, the battery drains quickly, so I always have to charge it while riding. Therefore, I have to unplug and plug the cord every time I leave the motorcycle and every time I ride again.
Was the one you received as per Image?
In the picture, each of the parts looked large and bulky, and the image seemed to stand out, but the actual product is a very ordinary Smartphone Holder.
Was the installation difficult?
The act of removing the Cowl and tinkering with the electrical system was too much of a hurdle for an amateur riding specialist, so I asked Timing to install it with me at Motorcycle Shop, where I would install a driver's license.
How was your experience with it?
It is only a small step, but it is much easier now that I don't have to unplug and plug the cord! The charging speed seems to be the same as from the cord.
Manufacturer's description. The Slide arm on the top can be fixed by simply pushing up on the phone, and can be removed by simply pushing up. Smoothly attach and detach the mobile holder with one hand." I have been using two hands because it takes a lot of strength (perhaps men can easily take it on and off with one hand). (Men may be able to easily remove it with one hand.) Since it is held firmly, I am not worried about it falling off while driving.
Vibration absorption is also said to be Standard Equipment (I couldn't really tell when I ran with it), and although I have never been particularly concerned about vibration with the Ninja, I'm relieved to know that it's there.
[Included Parts:were they on?
The screw for attaching the parts connecting the body and the mounting part was not of a common type, but had a special tool.
[Was there anything that disappointed you?
The part of the claw that holds the phone Body is Red color. It may be good for those who choose Red as a color scheme, but it is not my favorite color and I wanted it to be Black. I want to repaint it.
View detail
The product was of satisfactory quality.
Fixed to the AttachmentBracket and mounted on REBEL250.
There is no vibration that makes it difficult to see the screen when driving around town, and it is very comfortable to use.
I haven't tried it at high speeds yet, but I'm mainly a city rider, so no inconvenience.
The product is also compact and can be used with as little disruption to its appearance as possible.
The product was made by DAYTONA, and although it was a bit pricey, I was satisfied with the product as the price was right.
View detail
It helps me when touring!
I bought this to use when touring.
It is able to cope with the vibration of SR400.
There was no particular vibration that made the screen difficult to see or loose or any other Smartphone malfunction.
View detail
Wireless charging allows charging in the rain
[How is it used?
If your phone supports Wireless charging, you can charge it even in the rain.
Was the one you received as per Image?
Charger section is thicker and weighs 544g (figures announced on the agency's website) and somewhat heavy.
How was your experience with it?
The battery charge catches up slowly while playing NAVITIME and music.
I also like that there is an OnOff switch to prevent overcharging.
[Points to note]
Quantity the phone:When set, it is difficult to notice that the Charging Indicator is off (not charging) because the Charging Indicator is not visible unless you look into it from the side.
The USB Connector is not waterproof but comes with a Rubber cover.
[Opinions and requests to Manufacturer
Charging Indicator Lamp should be on OnOff switch.
View detail
Simple
I wanted to put it in an inconspicuous place, so I chose the Stem Mount.
Anti-vibrationModule and Universal Interface were also purchased, so the price was just under 17,000 yen, which is very expensive for a Smartphone Holder.
Well, I guess I'll just have to focus on design...
Fits in diameters from 15mm and up.
I put it on Center for now.
But
If you attach the phone vertically in this condition, you can hardly see the Meter.
The phone is an old Android model AQUOS sense3 plus
I shifted it to the Right side.
Now the Meter is visible. Now we will run it and check it.
I've only been running for a little while, and it's not something I want to watch while running, so I hope I won't be inconvenienced.
View detail
Smartphone Fixed Band. poor quality.
This is a Single Item of Smartphone Fixing Band with RAM Mount.
I bought it because the first one I bought with Base and Mount was torn off.
Made of Elastomer, it stretches like a rubber and holds the Smartphone in place.
The band has a small tear like a slit at the edge of the band shape, perhaps due to a molding defect. When the band is pulled to secure the Smartphone, the tear is stretched and the slit gradually deepens. It is a consumable item, so this may be a device to make it wear out quickly.
If this is the case with OEM Products, I don't know if there are any, but maybe the Copy products are better.
If nothing is done, it will eventually tear off, so I heaped some Cemedine SUPERXBlack on hand in the cut for now to extend its life. Hopefully it works.
View detail
Used with KDR-M11C
It came with the KDR-M11C so I didn't have to buy it.
I will keep it as a spare.
View detail
Mounted on BWS125
Installed on BWS125.
I use it on my iPhone 13ProMax.
It is a good product for normal use.
View detail
With a 4-cylinder 4-stroke, vibration is virtually eliminated.
I use it on my FZr250 and SEROW250, the FZr has less vibration originally, so after installation the vibration is really gone.
Because the SEROW is a single cylinder, vibration remains slightly, but is reduced enough to be effective in preventing phone malfunctions.
The height of the holder part of the smartphone is raised by the earthquake-resistant spacer, so depending on the installation angle of the holder, the smartphone may come closer to the Rider, making it difficult to see the screen.
View detail
SIGN HOUSE
Good to adjust to the Size of the phone. View detail
I can lock it down tight.
The make is Well.
The Spring of the claw that pinches it is also quite strong, and once locked, it did not fall off.
Thick Smartphone cases (round shape, approx. 15mm thick) can be inserted without any problem.
The body can be rotated and used either vertically or horizontally, but right-rotation is recommended when rotating the body.
If you use Left rotation a lot, the screws that hold the body in place will loosen. You may notice that the screws are rattling to a certain degree, so you should retighten them periodically even if you do not rotate the body.
We recommend using the included Silicon band as an insurance policy.
View detail
SIGN HOUSE
I don't know as it has only been installed for a short time. View detail
Easy to use
Installed on CT125. I bought the vibration-proof type because I heard that vibration causes Camera to malfunction. I think the vibration of the Motorcycle is transmitted to my phone while driving, but … I will check the effect from now on. View detail
Installation on GB350
I am very satisfied with the quality of the product, which is well above the price. View detail
Stable and Flexible
I installed a UA smartphne universal holder and bulb mouting adapter on my Suzuki V-strom 1000. I went through a juorney of 1,000km last month, during my journey it is very stable anh can be rotated horizontally or vertically very easily. View detail
Mounted horizontally
I installed a Screen on my car, so I installed this Smartphone Holder on the mounting arm of the Screen. The phone is large and the Screen is too small, so I had to install it horizontally. My phone is Xperia 5 IV and I was able to fix it by replacing the included extension parts.
When installing, use Color on the bar.:It was easy to put in the Gray protective rubber parts and secure them with the Silver locking parts. However, during the test run, the fixation was not tight enough and it came loose. It needs to be fixed a little tighter. Fixing the phone is also easy.:Pair (for Left and Right) The frame is fitted into the frame of the "I" and secured with a White Rubber Band, which provides a sense of security.
After a while of use, the upper and lower Quantities:Pair (for Left and Right) The lever becomes hard and does not move well, releasing the fixed frame of the Blowing lubricating oil revived it.
View detail
Opening Ritual
It is quite good.
The RamMount you are looking for in the Mount at 1InchBall is
I can't deny that it already feels old-fashioned nowadays, like dropping your phone.
Ka Edia was selected.
CaEdia has many different types in terms of shape, but other models are not so good.
It didn't feel right and I chose this one.
View detail
It seems to be effective.
Sadly, the Autofocus function of my Smartphone's Camera has broken. Since I mount my smartphone to my motorcycle every day, the vibration of the motorcycle is almost always the cause of the breakdown. Therefore, I installed a Vibration Absorbing Device.
The installed feeling is still different from that of SolidMount. Blah, blah, blah. The screen shakes when the screen is Large. If I were staring at the screen, I would be a little concerned about this vibration, but I never stare at the screen while driving, and if I were to glance at Navigation, I would say that the visibility is sufficient. As for the vibration absorption performance, the fine and hard vibration that may affect the Autofocus mechanism when touching the smartphone while driving seems to have been reduced to a Large size, so it seems to be effective.
Also, the size of the Vibration Absorbing Device is quite large, and if it is installed as it is, it will stick out in front of the Smartphone Holder by less than 4CM. Quantity of Vibration Absorbing Device and Smartphone Holder with reduced protrusion:If it is a Set product, the overhang seems to be within 2 cm, but it is very subtle.
I made some adjustments to the mounting and combined it with an adapter that converts the mounting angle to 90-degrees, which was included with the Miknowla Mount that I had left over at home, to optimize the mounting position and make the position and distance very easy to see.
In the meantime, I hope that the Autofocus function will not be broken.
View detail