Reviews
Used as Bracket for Switch on Grip heater
The Bracket that was originally attached was too long and was bent at the Prank, breaking it off at the base.
This time, I don't think it will be tampered with because the base LARGE size and height of the base are just right and not uncomfortable.
View detail
Required Items for ETC Installation
I was concerned about the mounting position of the ETCAntennas and Indicator, so I purchased it. View detail
Is good
It is a solid Bracket with a high quality feel.
Double-sided tape is also included and the angle can be adjusted freely, making it easy to use.
View detail
Mistuba Sankowa EDR-21 for switch installation
I used Mistuba Sankowa DriveRecorder-EDR-21 for Switch.
The mirror is used in conjunction with the Mirror. The switch itself is installed with double-sided tape.
The process is quite simple.
Lamp lighting is easy to see and easy to use since there is a Drareco Switch by the Handlebar.
View detail
EDR-21G GPSAntennas
I used it to install GPS Antennas on my EDR-21G.
I used it to organize the various items I have installed around the Handlebar.
View detail
Fits: HONDA Rebel 250, HONDA Rebel 500, HONDA Rebel300
It is easy to install.
Installation is extremely easy.
If the ETC Wiring is done properly, it can be installed in 10 minutes.
The dissatisfaction point is a little rattling because there is some rattling in the body and the lid part of Case.
I put it on my wife's Rebel, and I put Tape in the gap at the Level that I don't mind at all while driving.
The price is right for this type of product.
View detail
It's not too obvious.
It's a Compact Bracket and it doesn't look so obtrusive.
I chose the Type that co-closes with the Mirror, and the Indicator is perfectly visible in this position.
I don't think the price is cheap, but it's less expensive than other products.
View detail
Best Position.
The ETCA Antennas can be fixed firmly by installing with the Bracket for Antennas Body made by DAYTONA. View detail
I decided on the quality of the product.
It's been installed together with a DAYTONA Mirror Holder Bracket from the same brand. You can adjust the angle freely and fix it firmly with the attached Double-sided Tape. View detail
A lightweight and durable bracket.
This bracket comes with a powerful double-sided tape and is an effective bracket for ETCAntennas installation. It can be adjusted to any angle to increase the reception of the Antennas. There are three different colors to choose from, so you can choose the one that best suits your motorcycle. View detail
It is useful for Repair.
I bought this to replace my old ETCAntennas because the base was getting rusty and the double-sided tape was included and the angle was freely adjustable. View detail
In addition to ETC Antennas.
There is a way to use it by devising other than the Antenna Mount.
I used it as a mount for the Lap timer to be installed when running Circuit.
Once assembled, the neck section can be angled to make it easier to see the Lap timer.
View detail
Fits: HARLEY-DAVIDSON FXDL, HARLEY-DAVIDSON FXDB 06-17, HARLEY-DAVIDSON FXDWG 06-17, HARLEY-DAVIDSON FXDF 08-17, HARLEY-DAVIDSON FXDB 06-17, HARLEY-DAVIDSON FXDWG 06-17, HARLEY-DAVIDSON FXDF 08-17
We're going to change the mounting location.
I changed the location of the ETC installation because I wanted to avoid too obvious and visible places. View detail
enough
Other ETC brackets were too expensive to buy, but they were reasonably priced I bought it, and it has been used with no problems, although I have co-tightened it to Mirror View detail
COSPA
The thickness of the board seems to be thin, which bothers me, but I can only say that it is excellent in terms of cost effectiveness
Luxury products may have their own good points, but people who just want to be able to get ETC on them I think it's the perfect product for
View detail
Completely clean
Perfect for JRM-11 made by Japan Radio.
Tighten to Clutch lever holder.
Just because it is too conspicuous, I'm considering moving it around Meter.
View detail
It is a good deal..
I think that the usability is good because it is lightweight and it can adjust the angle.
However, angle adjustment many times (Bending elongation) Then, the surface Anodized (?) It seems Crack is in.
The hole of M6 mm is empty because it is used for fastening with the Clutch lever holder, but if it is 8 mm it can be installed anywhere..
I am satisfied because it is inexpensive compared with similar products of other companies.
View detail
I attached ETC.
I attached it to Mirror Holder.
Easy to do it did not interfere with the car body even if you cut the Handlebar.
It is a little heavy with thick steel, but there seems to be no blur of Mirror.
View detail
Simple & high texture
I exchanged from ETC Bracket of Tanax.
I am satisfied because it is a simple and textured product.
However, one point. If you improve another angle so that it can be adjusted.
We installed it in MT 07, but we can not adjust the horizontal direction so we bent the mounting part slightly across Plate. Since I chose Black Plate, Crack entered a little in the painting where I bent, but I think I should paint it (Lol).
It is the best recommendation if you can install it where the level can be kept.
View detail
Structure and texture are satisfactory. This is although it is a problem of how to use me... In order that bending part might tune finely, when a little angle was changed by hand, the Anodized cracked. So big power was not necessarily put
Structure and texture are satisfactory.
This is although it is a problem of how to use me... In order that
bending part might tune finely, when a little angle was changed by hand, the
Anodized cracked.
So big power was not necessarily put and only a few is also changing the
angle.Is it a problem of the quality of the
Anodized?
For using it as it is, it is satisfactory.
View detail