Reviews
It is quite good.
Although it takes 60 seconds to establish the connection due to the Radio Law, this product uses a soft power supply that shuts down 5 seconds after the ACC power is disconnected, so even if your car model shuts down the ACC power at the time of cell start, as seen in BMW etc., the power will not be turned off when the engine starts. Therefore, if you put on the Helmet and Gloves after turning on the key first, you will be connected to your smartphone by the time you step over and turn on the Cell, and you will not feel the stress of waiting for the connection.
If your vehicle is equipped with a 12~16mm GPS Mount Bracket, the Tanax AIO-5 Mounting Bracket can be used without modification.
The cost performance is great, but the screen size of 4.5-inches is a little insufficient.
View detail
Large sturdy even on Motorcycle as it is firmly fixed.
I use it on my Insta360 X3. (I'm planning to buy Ace soon, so I'll use it there as well.)
With X3, the position is so delicate that it just hits the chin of the full face, so I think other ActionCamera would have no problem at all,
The Camera is easy to put on and take off, and since it has two clasps, the Camera will not be upside down as is often the case with products that hang from the neck.
The fact that it is an official Insta360 product is also a reassuring factor.
It can be used for walking around town or in the mountains, except for motorcycle, and since the price is only 3,000 yen, one can be used for various situations and is very cost effective.
View detail
It can be used with a turnstile.
I bought this to attach my old Porch and Smartphone Case to my Scooter.
As others have stated in their reviews, it rotates when installing the Porch and other parts.
I solved the problem by adding a Nut to stop the loosening.
Because of its high quality, the appearance of the product without Porch and other products is not bad.
View detail
For the use of Income.
I have been using a btx2 pro s with a SZ-RAM4 and bought it with Speaker so that I could use it with my new SHOEI Z-8. I was so attached to the SZ-RAM4 that I couldn't bear to retire it, and since I would likely want to use Jet in the hotter months, I decided to keep it too. I decided to keep it, and the question arose as to what to do with Income.
When using Income, the Microphone is available in Included Parts:for full face, and it is sufficient to use the unused one in Included Parts:for the mounting Clamp, but the Speaker and SlideMount need to be replaced or newly prepared each time they are used. However, the Speaker and SlideMount need to be replaced or newly prepared each time they are used.
I thought about changing the Speaker and SlideMount for each season, but I decided to purchase the Speaker and SlideMount because it is troublesome to take off the interior and put on and off each time, and if I just attach the Body, I can use different Helmets depending on my mood. I decided to purchase a Speaker and a SlideMount.
For installation, we decided to use double-sided tape to attach the outside of the clamp, which was not used in the Included Parts:section, to the helmet, but the SlideMount, which we purchased additionally, does not come with two screws to fasten it to the clamp, We had to think of a way to fix it to the Clamp. At first, I was thinking of using one screw for each SZ-RAM4 and Z-8, but I didn't want to damage the screws by applying excessive force, so I decided to prepare screws. However, this was not the Size sold around the corner. I had to buy a clamp to attach the screws, and it cost about 2,000 yen for two small screws. I had no choice but to use the regular screws for the Z-8, and for the SZ-RAM4, which is likely to be used less frequently, I removed the Clamp once, removed the Screw holder from the Clamp, and fixed the SlideMount to the Clamp with 2.5mm diameter Screws and Nut to make it ready to be used. The Clamp was removed and the Screw holder was removed from the Clamp.
As for the wiring, in the SZ-RAM4, the wires were placed inside the helmet, crossing the edge of the helmet, so it was necessary to protect the wiring from damage when the helmet was placed on the ground, etc. In the Z-8, the wiring could be pulled inside the helmet without passing through the point where it hits the ground, etc., so no protection was needed. However, with the Z-8, it was possible to pull the wiring inward without passing through the point where it hits the ground, so no protection was needed, and the wiring was well concealed, making it look very refreshing.
After installation, it works fine and I can now use Income on my Z-8. For this gold price, I would like to see at least a Screw included in the kit.
View detail
Difficult to understand the settings
It does not include a detailed instruction manual, which is a problem when it is not connected to a smartphone.
I set it up while emailing Manufacturer.
Since the Instruction Manual is the same as the Instruction Manual that comes with the DriveRecorder, it is difficult to understand whether it is not displayed due to a defect or whether it was not displayed in the first place.
View detail
SP connect Anti-vibrationModule
I use an iPhone 12 and bought the anti-vibration because my Camera broke. It's been installed for about a week so it's not accurate yet,
I don't know, but for now Camera is usable.
It says it reduces vibration by 60%, but I don't know how much this is.
View detail
Effects not known.
I installed it to prevent my phone from malfunctioning.
The installation itself is easy, but so far the effect is unknown.
It would be nice to have three different hardnesses.
View detail
Neither good nor bad
The Rain Cover does not have much to say about it, but I think it accomplishes its purpose of protecting the user from the rain.
It can't be helped, but it feels difficult to operate Touch when it is attached.
It is too hard to keep it on everyday, so it is for rain only, but when it rains while driving, I have to stop the Motorcycle and put it on.
I wish it had a waterproof cover for daily use.
View detail
The installation is Large strange
When I put it on a Full Cowl Motorcycle, I had to remove most of the covers, which was quite Large and strange.
It took 2 days to install the body and position the Camera (including breaks).
BackMonitor was surprisingly usable...I don't think you can overstate the functionality of the BSD!
The Instruction Manual is too unfriendly. It seems to be telling you to learn by touch.
I hesitate to buy Option because it is over 100,000
I guess I was too quick to buy when I thought I could have gotten something comparable for less if I had waited a little longer...
View detail
KaEdia SafetyBand
The band was shredded after about a year of use. I thought it would be better to make the rubber a little thicker or a little softer. View detail
Mounting and Wiring are
[How is it used?
Camera faces the front properly.
Was the one you received as per Image?
As pictured
Was the installation difficult?
Since you cannot access the Mirror Nut without removing the Meter panel, you will have to do a lot of killing, but you can do it if you follow the Installation Instruction Manual.
How was your experience with it?
No problem
[Included Parts:were they on?
Bolt for fixing Camera is included but not Nut
It was used for mounting Camera of AIO-5, but the hole of Camera was too small to be used.
[Was there anything that disappointed you?
Wiring Cord bare
Installation Point or hang
Meter panel is ScrewQuantity:I was able to remove 2pcs and pull out the rest by force and work without removing MeterWiring.
View detail
Unfortunately, the length was good but the shaking while driving was not calculated.
Since the Meter on MT-07 is directly above the Handlebar, I wanted to place my phone and Car Play Monitor on the upper side of the Meter, so I chose this product with a longer bar length.
The length was good, but the Mirror mount bracket was not able to support the weight of the phone and CarPlay Monitor due to the Bolt1 pc fastening, causing it to shake considerably while riding. As a result, I moved the length of the bar to a shorter length so that it would be closer to the fulcrum. Since it still shakes, I am planning to change to a Bolt2-Bolt Type of Master CylinderClamp from DAYTONA and others.
View detail
It was a little long for me.
[How is it used?
After six months of hanghang and Restore&Custom work on the LITTLE CUB, I thought I'd get comfortable with the next stage of the project. First, we need an external power source. I started looking for a USB power supply, but realized that there was no place to install them, so I looked for a Mount Bar in Webike's product introduction section and bought a Multi Bar from Made by HURRICANE, which had a safe design.
How did you like it?
Although I knew it existed until now Messy around the Handlebar. The Mount bar had never been used before because I had the impression that it was too heavy.
The fact that I had a safe length and design for my first Mount bar purchase and I was a teenager. Separate handle (Handlebar of Separate type)". Speaking of Other Brand Products of "HURRICANE It was an Image that I was not surprised to see. Finally, I too will buy HURRICANE products." I bought the Multi Bar at Tension...but the bar was a little too long for my use.
Please don't get me wrong, the product itself was a good product with good rigidity, but for my personal use, I would have preferred a shorter length, so after much thought, I replaced it with a Mount bar made by another company.
We wanted to use a Short Type Mount Bar to make it as Refreshing as possible, since we only need to be able to fix the USB power supply and Smartphone Holder.
How did it compare to other products?
If it is a MAJOR Manufacturer's product. "A damned glitchy piece of junk." I don't think there are any.
Before you buy Which car? of Which part? and there you want to install it in What do you want to install?" I think that Risk can be reduced if you take into account the following before making a purchase.
[Points to note]
This product is a type that is attached to the Mirror Holder by fastening it to the Mirror Holder, so it is easy to set the quantity to a position that is easy to use.:Once set, please tighten and secure each part firmly, otherwise you will be in a hurry if it loosens while driving... (This is a testimonial.)
Other items that would be helpful
The deciding factor in the purchase
As I mentioned above, I didn't even understand the difference between the Mount bar and I didn't think it through. HURRICANE Products I bought this product only because it was a very solid product with no fault of this product over and over again.
【Included Parts:presence or absence】.
Bracket for connecting Mount Bar Body and Mirror Holder, 2 Washers and Spring washerQuantity:1pc. and Nut included.
[ITEMS TO BUY TOGETHER
Products to be installed on Mount bar.
If you purchase the products you want to install at the same time, such as a power supply outlet, Smartphone Holder, Drink Holder, Camera Mounting Holders, etc., you can proceed with the work at a stretch.
Opinions and requests to Manufacturer.
It resonates with my father's generation. "HURRICANE BrandName, we look forward to continuing to serve you with a variety of custom parts at affordable prices.
View detail
Your Edia Sun visor
Purchased as a countermeasure against thermal runaway in the summer and against not being able to see when the sun shines.
Since the purchase was made in December, I guess we will have to wait until next year to see the effect.
View detail
Fits: Others AIO-5 Lite
Neither good nor bad
Installed at the same time as SMARTRideMonitorSRS-001.
Or rather, it is a product with Monitor.
To install, simply screw it into the Valve cap.
There is nothing difficult to do.
The Monitor displays Tire air pressure and temperature.
A warning will be displayed if the pressure is less than the set pressure value/Large.
To be honest, the TPMS I used to use has more functionality than that, such as being able to set air pressure in the front and rear Tire and check it on my phone.
Well, since we have SMARTRideMonitor, I will use this one.
View detail
Bolt hole
Since the Bolt hole position was different by about 5mm and could not be installed, it was installed by making a long hole with File. Forced installation may damage the screw holes. View detail
It was saved.
I purchased a new Helmet.
I think it is LiNori that I don't have to buy the whole IncomeBody, but I felt it was a bit pricey.
View detail
It was saved.
I purchased a new Helmet.
It was quite helpful not to have to buy the entire IncomeBody.
View detail
It's a bit expensive
I want to mount my phone in a position where I can see it easily on my Racer9GT, so I have a FairingBracket installed.
However, the bar to mount is 12mm, which is considerably slimmer than a handlebar, so I had to use a regular mount base with a Gon Seat or something like that, but I found a product that is perfect.
It was originally designed to be attached to the bar portion of Mirror, but the size was JUST right. Spacer also comes with several sizes to fit various sizes, so it can be used for other purposes.
The Base that originally came with the RamMount was ported to the other Motorcycle, so the Arm and Body can be used.
Still, this price seems high for Base alone, but...,
View detail
Easy
[How is it used?
For Touring's smartphone Navigation.
Was the one you received as per Image?
Almost as per Image.
Was the installation difficult?
The tools required are also Quantities:Set so anyone can do it.
How was your experience with it?
As long as the Holder part does not interfere with the Meter, it is a good thing because it is easy to attach and detach the phone, and it is also cosmetically pleasing.
[Included Parts:were they on?
Yes.
[Was there anything that disappointed you?
Holder is plattic, so deterioration over time may be inevitable.
View detail