Reviews
I lost it, so...
22.I lost my ClampSpacer for 2mm, so I bought Repair Parts.
Only Repair Parts can be purchased for fragile parts, so they can be used for a long time.
View detail
Touch screen is slow to respond. Instruction Manual is too easy.
The instruction manual only describes it roughly, so you have to learn how to use it by hand. Except for disassembling the bike, wiring is not difficult with color-coded connectors. However, since the connectors for the front and rear cameras are the same color, it is recommended to temporarily turn on the power in the middle of the installation (since the rear camera has a reversing function). If you are concerned about the dark current, the instructions say to connect both ACC and constant power to ACC, but I connected ACC and constant separately because I was concerned about the inability to use the parking monitoring function and the time gap. If you use your motorcycle infrequently and are concerned about battery drain, it is better to use only the ACC connection for constant and ACC. As mentioned in the title, the response of the touch screen is sluggish. It is frustrating with gloves on. There is no automatic screen illumination adjustment (I always use max except at night). The smartphone app is supposed to be able to connect to the driver's recorder, but I don't know the password, so I still can't use it. The home button on the map screen is annoying. View detail
No functional problems, but ….
No functional problems, but the paint started cracking and peeling about a year after installation. There is a problem with the quality of the paint or the painting method. View detail
It slips and moves.
Used to attach the Smartphone Holder to the Pipe behind the Screen on the Honda 400X (2019) (with an additional Spacer that comes with the Smartphone Holder).
The size itself is just right, but the hard rubber makes it slippery, and even when the bolt is tightly tightened, it slips and moves. Therefore, I wrapped a thin double-sided tape around the pipe on the body side before installing the bolt, but it is not completely fixed because the outer side of the bolt also slides.
I'm considering replacing the Arm of the Holder with an aluminum spacer only for the type that is tightened with ZETA Bolt.
View detail
Higher height.
I bought this when the Autofocus on my previous iPhone 11Pro Camera broke.
Type VibrationControlDevice to be attached to existing Smartphone Holder3
Just Smartphone Holder3+ IH2100Rigid (25077) The pull-pull mechanism is about 20mm higher than that of the "M" and it shakes more when a smartphone is attached.
I think it can absorb a certain amount of vibration, but the increased height makes it look bad.
If I were to purchase an expensive SMARTMonitoretc. without a phone attached, I would be willing to purchase a used Android phone and use it with TetherRing.
View detail
Fits: HONDA CB400 SUPER BOL D'OR, HONDA CB400 SUPER BOL D'OR, HONDA CB1300 SUPER BOL D'OR, HONDA CB1300 SUPER BOL D'OR
Processing is necessary for installation
The bolt that came with the kit did not fit the screw holes, so I extended the holes in the bracket with a drill to M7, but could not install the bolt.
I installed it with an OEM bolt and it fits the screw hole. (I think the upper side of the OEMBolt was thicker, so it fit better and had a Screw hole.)
I put it at 2 because it needed processing even though it was an exclusive product.
2019 CB400SB (2BL-NC42) is
View detail
PC application compatibility complaint
I used to use CHINA.
There were a lot of glitches.
I am replacing it with Mistuba Sankowa product.
I am satisfied with the product, but
Data import to PC application is unsatisfactory.
About half of the data recorded on the SDCard cannot be imported.
I have contacted Manufacturer, but there has been no response, so I am dissatisfied.
View detail
DriveRecorder worn on the body
I bought this one because I didn't need to splice Wiring.
I hung it around my neck and used it with an automatic motorcycle. I dare call it an automatic motorcycle.
Fitted full face helmet
MotorcycleType Sports Type
The result of using the front Camera has an image, and the Rear Camera has no image. (Helmet is interfering with Camera.)
Battery is limited to about 3 hours.
In conclusion, a Motorcycle is a Motorcycle is a Motorcycle is a Bicycle!
Battery also may not be able to take pictures at critical moments in long touring.
If the battery runs out because it cannot run while charging, it would be dangerous because there would be a Damage to the neck if the equipment was worn around the neck and the person was falling.
Needs a little more evolution.
View detail
It works for now, but ….
I repurchased this product because my previous purchase of the same product broke.
As it turns out, the malfunction was probably caused by the midsummer heat. After the malfunction, we rebooted the system, but could not solve the problem.
As a Lap timer for the time being, it may have some Advantage in terms of price, availability, etc., but it may not be a product that can be with us for a long time.
It would be better to use Awning in the summer or take other measures.
I was disappointed because this is a Manufacturer that has provided us with a relatively good product.
View detail
Failed 1 year and 3 months after purchase.
One year and three months after purchase, after about 10 times of use, a series of errors occurred and measurement became impossible.
I contacted Manufacturer and was told that it could be a Short in the internal infrastructure.
Unfortunately, it broke slightly past the one year warranty period, so we were unable to replace it under warranty.
The price of the Lap timer is not high, but considering that it will break down in a little over a year, I can't say I recommend it.
View detail
Fragile Construction, bad quality plastic.
This item looks very promising in the pictures. I really liked the design. In reality It is very weak. It is made of a very weak type of plastic. I have seen cheap phone holders for 7usd that use better material. There are very important parts in this design that should be made of metal, but in this case those are made of thin plastic. From the outside It looks like the body is made of aluminum, but it is just a decorative sheet metal part. If I knew, I would not pay more than 12 usd for this product. On the other hand, the vibration damper doesn't seem to do much. The Handlebar clamp is made of aluminum, but because it is very thin, It looks like it will break if you tighten the screw too much. Don't use this holder on single cylinder bikes, because the damper is not effective enough. Be very careful when installing this product, because It is not made of strong material and it will break If you tighten the screws too much. It looks like It will not last much under the sun either. For 52usd I expected a sturdy well built phone holder. It doesn't look like it was made in japan because of the cheap quality. It is expensive, bulky and flimsy. Next time I will try with SP Connect. View detail
It's fine …
It's fine, but …I think it's going to have a Daytona Attachment Bar on the BURGMAN 200.
I have the impression that it is very expensive, and I regret that I should have bought the cheaper Universal.
The product itself is solid, so it's not a failure, but I can't shake the feeling that it's not quite right.
I think you can wait until the Other Brand Product comes out, or you can use the Universal Product that attaches to one of the Mirrors. Not recommended.
View detail
communicate by wire
It's a great product to use, but
Due to the failure of the wired Disconnection there is
If it's a broken wire near the Speaker
Speaker for Repair is available as a Single Item at a discount.
Wallet-friendly maintenance is possible.
However, the disconnection between Body to Jack
It was overwhelming and troubling.
To prevent wires from getting caught when removing and installing the full face.
Even if you take care of it, the disconnection will continue, even as a User.
I can't think of any more countermeasures.
I tried a wireless Earphone after 3 wires were broken.
When I take off the helmet, it falls off and I can't do anything about it.
After all, there are no other flat Speaker options.
I bought a fourth one.
Rather than adding FMRadio functionality
I wonder if you could take care of the disconnection near the Body exit of the line.
The disconnection near the Speaker is
Speaker inside HelmetPad cover
By putting it in, it's totally gone.
View detail
Not for use with Stainless Steel Hose
I have a Stainless Steel Hose from Swage line and could not use it due to interference.
I could have used it if it had been directly below without the odd Offset...
I think the OEMHose is SMART and easy to install.
View detail
Defective in protective rubber
When I tried to charge the battery, I removed the BlackRubber that is attached to protect the important parts of the Power Supply Cable etc. and bent it slightly, and the part connected to the Body was cut off. Since the body and the rubber part for protection are now separated, I have to be careful not to lose it when I charge the battery. I was disappointed with the quality of the product and was dissatisfied with the defects that occurred immediately after opening the package. Is it really JAPAN? View detail
Smartphone cannot be fixed properly
I chose the RAM Mount because I thought it must be a good product since many people use it and a large percentage of Len BarrelMotorcycle models are equipped with it. However, the holding of the X-shaped retainer is not so good, and the Smartphone gradually gapped on a motorcycle with a lot of vibration, and before I knew it, I had to press the SIDE button. Also, when the X-shaped retainer is expanded to hold the Smartphone, it rotates by the amount of the expanded angle and cannot be fixed. It was not easy to use, so I immediately replaced it with another product. View detail
If you can connect two BT devices, why didn't you make it possible to use A2DP for both?
Alternate from BTX2 PRO S.
The Button is Large and the projection is easily recognizable, so operability is not a problem.
The new installation method, attaching the Body to the Base is good, but the Button for removing the Body is too small and difficult to operate.
At least it is impossible with Gloves on. Even with bare hands, the Switch is hard and my fingers hurt.
Why should I have to go through the pain just to remove the Body from the Base?
Regarding functionality, there are two BT devices that can be connected, but the Profiles that can be used are
A2DP/HFP compatible Bluetooth devices can be connected to the?Button.
Bluetooth devices supporting HFP/HSP can be connected to the Button.
He said
Why not just make it possible to use A2DP for both the normal...
Speaker did not feel notably better.
However, it's not harder to hear than the HiFi version, but it's neither better nor worse, just normal.
Compared to the BTX2 PRO S, the only Merit is BT5.0 and RCF, so I don't think it's worth replacing it.
I honestly think I should have kept the BTX2 PRO S.
So I am less satisfied.
Honestly, I want to return it because it is so disappointing lol.
View detail
SizeSmallest
I installed the bolt on the front fork, which is supposed to support up to 54mm, but I think it is difficult to use the supplied bolt. I prepared a longer bolt and managed to install it by bending the receiving part. The quality is not good for the price, and the paint is also scratched.
It will probably rust after a while.
View detail
hmm
I guess it can't be helped because it is a combination product, but the pitch of the Bolt where the Number is mounted does not match. Also, in the case of ZX12R, depending on the angle of the Fender Eliminator, the camera mounting part may hit the rear cowl and there will be no space for the camera to be mounted. I had to cut here and there, so I painted it. View detail
Plastic Parts are too fragile.
Material:Plastic Parts are too fragile.
It is not that the Bolt was tightened with stupid force or that a hard object was slammed against it, but the Plastic snapped off in the order of the claw on the top side that holds the phone in place, the Body side that holds the middle claw in place, and the middle claw, making it unusable within one year of purchase.
The composition of the plastic seems to be hard and brittle, and if the phone is put on and off many times, it seems to get fatigued and go badrill.
I think that if the composition of plastic is changed to something more tenacious, or if it is made of gold, the durability will be improved by a large margin.
I would like to see DAYTONA improve on this.
View detail