Reviews
![Pro Wireless Remote Control [for AIO-5Lite]](https://img.webike-cdn.net/catalogue/images/128410/SRS-006_01_TS.jpg)
Very convenient
I have been using AIO-5 Lite for 6 months.
I thought I could do without it, but in my use Situation, I use CarPlay and Rear Camera quite a bit differently.
I have many Cases and purchased this one, which can be operated without taking my hand off the Handlebar.
When the Handlebar is turned all the way to the Left, the REMOTE CONTROLLERBody and the Inner of the Cowl are slightly in contact with each other.
Coped by sticking Sponge tape on the corner of the REMOTE CONTROLLER.
View detail
REMOTE CONTROLLER installed.
It is good to be able to operate it with REMOTE CONTROLLER without having to Touch the screen, although it is operated while the car is stopped. View detail
ETC Antenna BracketTYPE 3
Can be installed by co-tightening with Mirror Bracket.
Installation should be completed in 15 minutes.
The product is not very thick, so you can slightly adjust the direction of the ETCAntennas etc. by hand.
View detail
![[FreedConn][For R1-PLUS]TapeClip](https://img.webike-cdn.net/catalogue/images/111819/r1-tape-clip_TS.jpg)
I have several Helmets, so that helps.
[FreedConn For R1-PLUS I have several Helmets, so I bought the Speaker kit separately, and here is the Plate for when I run out of Income attached to the Helmet!
It's the one and only. (Lol)
View detail
With a sense of security.
If you are looking for a bar mount, this is it.
Bar mount at 1 inch This is a safe bet.
View detail
Well done.
Purchased for THRUXTONRS FE with KaEdia
The cheap ones will drop the phone, so this must be it.
The joint between the ball and the body is a little loose.
It comes out a little bit when you push it in.
It doesn't matter because I stop at Screw, but it bothers me a little.
View detail
Fits: KAWASAKI Ninja ZX-4R SE
M820WDController CT110 HUNTER CUB Brake folder Exactly for mounting
[How is it used?
MiVue M820WD Drareco Controller mounted in the Right SideBrake folder of the CT110 HUNTER CUB2BJ-JA55.
Although the name of the folder is Clutch folder, as shown in the product description photo, the folder can be attached to the Right Side Brake folder as well, effectively and securely.
Was the one you received as per Image?
Yes
Was the installation difficult?
It is easy. The angle of the brake lever changes when the brake folder fixing screw is loosened for installation. If you mark the current position before loosening the screw, you will not have to readjust it when assembling.
How was your experience with it?
It can be mounted securely, making it easy to work with Switch operation.
[Included Parts:were they on?
Yes. Matching mounting Bolt and collar are included and ready to install.
[Was there anything that disappointed you?
There is none. As expected.
▼ Requests
It would be easier to find a Brake folder if the name of the product listed is "Clutch holder...".
View detail
Good visibility
It is easy to see and use even during the day. It is also good that USB can be used for power supply. View detail
It's secure
[How is it used?
Used for FrontCamera installation of the MiVue M820WD driver recorder.
CT110 HUNTER CUBFrontCarrier mounting bolt was co-tightened to the Bolt. Although this is not where it was originally intended to be used, it was securely installed.
Was the one you received as per Image?
Yes
Was the installation difficult?
Easy!
How was your experience with it?
I am satisfied with the image and no shaking.
[Was there anything that disappointed you?
Expected
View detail
STREET TRIPLE2023 KDR-D21 installation
I had already installed it on March 16,
This is an Impression after using it for a while and doing various settings since it did not come with a proper Instruction Manual.
First of all, installation is a simple matter of connecting the Attachment power supply, Battery power supply, and Earth.
If you know how to get power, you can DIY it. The other thing to do is to install Wiring.
In this respect, it would be good without the Instruction Manual.
It is a Camera, but I like the fact that the length of the Wiring is different for the rear and the front. However,
Why are the terminals at the connection points the same color! I don't know which way to connect...
Also, as others have mentioned, the Cap for the Air Pressure Sensor had the F and R reversed. Also, I had to disconnect the battery and reconnect it to connect to the Body.
Well, so far, it's the usual Trouble in doing DIY, so I'll leave it at that.
I'd rather have nothing. What? Nothing?" I think.
From here on, it is a feeling of use. However, since there is no Instruction Manual, it is difficult to set up the system.
Touch panel is a bit dull. I guess this area can't be helped because of the low price.
I am an iPhone and it is CARPLAY, but it takes a long time to connect.
Do you want to connect to CARPLAY 60 seconds after turning it on? appears about 2 times after turning on the power.
I can't wait, so I'm running slowly and warming up until the connection is made.
As for the connection, it's like this, so if you CHOINORI and turn the key Off
It is a hassle to reconnect each time.
The Touch panel is dull, so smooth navigation is possible when using the iPhone to search for routes.
I feel like my iPhone battery runs out faster since I started connecting to this.
All of these electrical systems are the same, but the length of the connection terminals coming out of the Body is the same.
If the terminal part is the same length, only the terminal part will swell up when it is put together...
If possible, I would like them to be connected with one wire because they are bulky, or if there are four wires coming out, I would like them to have two different lengths for each wire.
Finally, the
The good part
No need to worry about battery level since it is connected to the vehicle.
I heard that people who connect to Income can operate it by voice,
It can be operated without using the Touch panel. (I do not use Income).
This price includes Air Pressure Sensor and Front and Rear Camera.
The bad part
The iPhone battery runs out fast. (I think this is the same with all machines)
Touch panel is dull.
No Instruction Manual.
BallMount, so lower Quantity:Cannot Set. (I used SP CONNECTO)
The hardness of the Camera's feet makes it difficult to wear on round surfaces.
Is this how it is?
Frankly, I don't recommend this for those who already have a driver's license.
The price is low, so it is good for new installations.
View detail
ease of use
I purchased this for mounting a Camera on my Motorcycle using Ram Mount Parts.
The mounting is no problem, but it is troublesome to adjust the position and angle of the Camera for attaching and detaching the Camera because of the screw tightening only, so a quick release mounting is attached to the CameraAdapter.
View detail
Cospa best
It is easy to lock and the mounting strength is Firmly fixed, unmatched by other companies. View detail
good
I installed it on my current Ninja 400.
There is no detailed year information on the webike, but it can be installed on a '23 model.
I had a hard time deciding between DAYTONA and WorldWalk's Mount bar, but I had used WorldWalk's Mount bar on my GSX250R before, so I decided to go with it again this time.
Installation is very easy as all you have to do is remove the screw at the handlebar and install it. (about 5 minutes)
I just put it on, so I don't know how durable it is, but it is a good product and well made, so I am recommending it.
View detail
Fits: KAWASAKI Ninja ZX-4R SE, KAWASAKI Ninja ZX-4RR, KAWASAKI ZX-25R SE, KAWASAKI ZX-25R
Good vibes
I thought it would be more rugged.
It's not so bad.
View detail
Purchased due to malfunction
It has been about 2 years since I purchased Income. I bought it to try it out because I was the only one who was having trouble with Noise when I was using it.
I was hoping that it was not a malfunction of the Body, but when I tried to use it, I was able to hear it properly.
I think the cause of the failure is that Helmet was used with the speaker left inside even when Income is not in use. Considering the heat during the summer, it may have been a state of considerable overuse.
So you might want to leave it off when not in use.
View detail
Fits: HONDA CBR1000RR FIRE BLADE, HONDA CBR1100XX SUPERBLACKBIRD
Suitable for Separate Handlebars
I purchased this for a new installation of SENA's MESHAntennas. I re-installed the Antennas on the Multi Bar that previously had the Smartphone Holder and the Smartphone Holder on BPYamato's AluminumMount Bar. It is a product for CBRetc. SS. View detail
Nice detail but good ??
I like it because it's easy to dress up and immeChain ??
However, it sometimes hurts that most of the colors are out of stock….
View detail
Fits: SUZUKI GSX1300 HAYABUSA, HONDA CBR400R (2013-), HONDA CBR500R, HONDA CBR500R
Multi Bar with USB power supply for convenience
Quantity of Smartphone Holder:If set, the USB power supply can be conveniently located nearby. The installation can be safely used in conjunction with the key by connecting it to ACC.
Connected to DAYTONA Attachment Power Supply Unit D-UNIT.
View detail
Size selection with room to spare is recommended.
I had been using DEGNER's Porch, which is compatible with P.A.S. Mount, and purchased it to install it in a vertical position in combination with Meter and other equipment due to a change of vehicles.
Back provided for Camera [Color] It is a Clear window, but it also has a secondary use through which you can see the meters on the other side of the Porch.
The size of the iPhone I am using can fit in the Smallest Type of the same series, but this size was the best for me because it allows for more room when considering Cable's handling.
View detail
Fits: KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI Ninja 1000SX
For Smartphone Holder installation
I bought it for Navigation and Smartphone Holder installation. View detail