Reviews
I would choose the phone.
I bought it because it is famous. I am not worried about it falling because it is firmly fixed.
However, due to its shape, there is a possibility that the button on the phone may hit the device, and while the Xperia5 had no problem, the AQUOS WISH had a button problem. Before purchasing, please pay attention to the position of the button on your phone.
View detail
Intuitive operation is not possible (i.e., must be learned).
I had been using a Chinese product for a long time, but when I joined a new touring group, I couldn't connect with them and was forced to choose JapanBrand for peace of mind.
Still, the price is lower than SENNA and B+COM.
While we have not yet used GroupTalk with other important models, we were able to confirm the quality of the sound when using BT connection with a smartphone.
It is also good that the base and body (harnessassy) can be separated and that the harness is not plasticky.
However, as the Title says, it is not easy to use and cannot be understood without an instruction manual. It is difficult to understand the roles of each button, perhaps because of the emphasis on design.
As you said, the MButton is hard to press, and it seems to be a bit difficult to press while wearing Gloves and driving.
Since the motivation for the purchase is GroupTalk with other models, it is enough to confirm the rest.
If I can't do it, I will change my rating.
View detail
Surprisingly time consuming to install.
The car model is Exclusive Design, so it can be installed without interference.
Ideally, I would have liked to install it a little lower, but that was unavoidable.
I'm replacing the OEM Handlebar Clamp Bolt with the supplied Bolt.
It would be appreciated if the Instruction Manual could include the tightening Torque of Bolt. (OEMBolt is 25N?m)
I have read other people's (J.P.P.'s) review of the Large odd useful installation instructions.
I had a hard time tightening it as shown in the third photo because the Hexagon socket I had was too short.
View detail
DAYTONADT-E1
It is also excellent for pairing with other Incomes, and is ideal for touring with up to 4 people, but the charge seems to be low. View detail
Fits: HONDA VTR250, YAMAHA MT03, HONDA Forza300, HONDA CB500X, HONDA CB500F, HONDA CB150R, YAMAHA XSR900, YAMAHA MT-25, YAMAHA MT-09, SUZUKI Gixxer 150., SUZUKI Gixxer 250, SUZUKI DL1000 V-STROM250, HONDA HORNET250, HONDA FORZA Si, HONDA FORZA Si, HONDA JADE, HONDA glom, HONDA CROSSCUB110, HONDA APE 50, HONDA XR100MOTARD
NAKED has this
This is used for NAKED cars because it is convenient.
It was not compatible with NAKED, but can be attached to NAKED with Large body.
View detail
Even with the phone Cover installed, I managed to get it to work.
I am replacing a Daytona MiKnowla OEM. When I changed my phone to Sharp AQUOSR6 and installed the Cover, the vertical side became 17cm, so I had to remove the Cover and install it when wearing Motorcycle for a while. It became more and more troublesome, so I purchased this product and it LimitClear even with the Cover installed. Personally, I think it is a good idea. Smartphone Holder I don't like the chunky Aluminum because I don't want the machine feel of the Aluminum, but the convenience is much improved. I don't feel like my phone is going to fly away when I use it, so I think it's up to par. If you have similar problems, I think you will not regret buying this product. View detail
Sensor installation is troublesome
[How is it used?
Circuit
Was the one you received as per Image?
Image Street
Was the installation difficult?
I want to remove the sensor when driving on the street, so I need to devise a way to install it.
How was your experience with it?
Sensor installation is troublesome
View detail
I use it on my iPad Air5.
Purchased for use on a tabletop or in a car, not for mounting on a Motorcycle. I use it with other Suction Cup type, Clamp, Arm and other Ram Mounting systems.
I usually carry around my iPad Air 5 with a Case that can also be used as a STAND, but I don't like to remove this Case and attach it to the Holder every time, so I was looking for a Holder that can be used with the Case still attached. RAM MOUNTS RamMount TabTight for iPad (1st-4th Gen) I decided to try the As a result, it can be used normally with the Case installed. Charging in this state is also “somehow”possible.
The product is not used in Motorcycle, but in daily life Level, and there has been no drop in this state so far.
View detail
Smartphone Holder that looks SMART
Purchased to attach Smartphone to Motorcycle.
Apart from this, a UniversalSmartphone Case from SP CONECTO is used.
Removing and attaching the Smartphone is fairly easy and only requires a 90° turn. It is the fastest way to attach and detach a Smartphone.
There are similar products, but Advantage is the Large size in terms of quality and ease of removal and attachment with one hand.
It can be detached by simply rotating it, but there is no locking mechanism such as a turnstile, so some people may be concerned about it falling off. However, the
If it is firmly secured, it is unlikely to fall.
View detail
Installation to Gixxer
I can only upload a few pictures, so here is the installation section.
Adjust the Screw→ of the Bracket to match the Phone.
I've seen a lot of Amazon Reviews. I tightened the screws and the plastic part broke off! The quality is too bad!"
but, well, I don't think so if you do it with normal additions and subtractions.
The upper part of the Body and the Bracket are joined by a grooved disk. If this is too tight, the Body cannot rotate freely horizontally or vertically. If it is too loose, the phone cannot be rotated freely.:When it is not set, will the Bolt come off and drop out due to vibration? Just right is Torque 3.6Nm, they say. Anaerobic adhesive (Screw looseness stop) I'll even use it …
I've closed this one too many times. I rotated the Holder and the whole disc cracked. or something like that (Lol)
I tried closing it by hand and got a good feeling, but there was no guarantee that it would not fall off even if I closed it with Torque 3.6Nm, so I decided to put rubber packing on it. It felt really good!
Cure with Tape, cut and fit the enclosed CushionRing.
Beyond this point, frame along the groove of the Ring. Tuning Screw." I just add or subtract the "+" or "-" to a good degree, snap it in place, and that's it. I don't even plan to remove it. Tuning Screw." to squeeze in Wrench.
Tilt angle adjustment with Screw above it
Cool!!! I couldn't post a picture of it. (Lol)
View detail
Mounted on ZX6R Tank Fixed Bolt
[How is it used?
ZX6R G type for creating a phone mount.
Was the installation difficult?
Simply remove and replace Bolt.
A separate M6 bolt of about 50mm is required.
The OEM fixed Bolt is M6 30mm.
How was your experience with it?
I used it to create a pedestal to hold the phone in place with Rec Mount.
Generally, I think that Multi Bar is often installed on ZX6R, but I chose this product because I wanted to make the steering area as refreshing as possible and did not want to put a large and conspicuous Multi Bar or Smartphone Holder on the ZX6R.
The Smartphone lock can be removed from the Arm when not in use, leaving only the ball joint. When not in use, the entire Arm can be removed from the Smartphone lock, leaving only the Ball joint.
[Disappointment.
The texture of the resin is poor and looks cheap.
It is fine for use, but it has a "Made in USA" feel to it.
[Notes]
Ball diameters may differ between Ram Mount and Rec Mount, so it is best to check for compatibility before purchasing. Some products are compatible.
After installation, Quantity:Pair (for Left and Right) The only thing that needs to be checked is that there is no interference with the Top Bridge when the Handlebar is cut to
View detail
Before your iPhone breaks
Many of my Motorcycle friends have broken their iPhones due to vibration. The new iPhone model has no fingerprint recognition and only face recognition, so it is very inconvenient if the Camera breaks. Since the iPhone New Model has no fingerprint recognition and only face recognition, it is very inconvenient if the Camera is broken.
Is the Holder itself dangling? It seems that there is a difference between the wobbling and the slight vibration from the handlebar, which is similar to the iPhone, and the vibration absorbing unit is as large as a 500 yen coin. (Lol) This would work well. It looks like it can be installed without the Vibration Absorbing Unit, but the height of the integrated unit is not the same.
Plate is plastic, but brackets are material.:Aluminum
The claws on the Defferential Gearo are deep enough to hold the iPhone 11-13, but only the claws on the moving parts are enclosed in a deep size.
Made in Japan tickles
I don't think the aluminum parts will break, and the quality is not too bad, but the claws are plastic, so I wonder how long they will last… I wonder how long they will break if I put a lot of pressure on them as they age.
So the quality star is 4
I wondered, but all PartsRepair Parts are out there, so I guess to some extent it's wear and tear Parts. (SlideBase set is 528 yen)
I think the thought that if you fix it, you can keep using it is Large cut. That's a very favorable attitude.
The reason why the Cost performance is 5 is because the price of SYGN HOUSE is from 28,000 yen like this, so it is cheap even if you replace the consumables. (Lol)
View detail
A little more room for maintenance would be a no-brainer.
We have had a malfunction that prevents us from recording and have contacted the Manufacturer.
Cause. Disconnection This was due to the
I have not disassembled it myself, so this is just a fantasy world.
If you repair it yourself, even though the joint is protected with Resinetc.
Since there is a vibration problem, we would appreciate it if you could design a system that places the highest priority on maintenance.
I believe it was a design issue with Balance for Noise and Weight for vibration response.
We are satisfied with the response of After Service as a Manufacturer.
Not only did I have no complaints, but the Large change was wonderful.
View detail
Tightly fixed
I originally used DAYTONA's old Type.
However, with this, the SIDEButton on the phone was pressed, and it was hard to use, so we changed it to this one.
It is easy to use because it locks securely, and the fact that it can be rotated is also a good point, although this is a matter of taste for different people.
View detail
Fits: KAWASAKI ZX-14R, KAWASAKI ZZR1400 (ZX-14), KAWASAKI ZX-14R
It's exclusive to the car model and EXACTLY!
I purchased this for the installation of a Smartphone Holder and USB power supply.
Compatible with ZZr1400, ZX-14, and ZX-14R, with a common bar thickness of 22φ.
In my case, I already had a HandlebarUPSpacer installed.
I thought the supplied Bolt was not long enough, so I prepared it separately.
Impressions were that it was a good size and looked nice and refreshing.
However, the instruction manual was for a Honda Africa Twin, which may have been a mistake.
I didn't have any problems with it because it never fails to install.
View detail
I think it's good
It's no longer available on Web!ke, but you can buy it on Amzon as of 1/19/2023.
I am satisfied with the operability, picture quality, etc. 4Inch is just right for the handlebar area of a large car.
The durability of the product is 1 because it has not been used that much yet, but that does not mean it is bad.
At first I thought Monitor was unnecessary, but one Review
I never notice if there's an error or Cable disconnection." when seeing that Indeed!" I chose the Monitor type because I thought it would be easier to use. Also, we chose this product because the touch panel would reflect the body and we did not need to worry about the durability of the button.
I am more satisfied with the monitor than anything else, as it increases the number of devices displayed. It can also be used as a back monitor, although it is sometimes difficult to see due to the light. When I twist my body and look back to check the back of the vehicle when turning a corner, I tend to lose my balance, so I can see the situation directly behind me while looking at the front, especially with a heavy motorcycle.
The installation was done by a motorcycle shop. I don't know the details of the labor cost, but I guess it would have been about 20,000 yen for a single body. After all, I had to redo the detailed camera position and wiring by myself.... If you have confidence in electrical components, I think you can do it all from the beginning.
Body, Camera, Sensor, REMOTE CONTROLLER, etc. are color-coded for easy identification of Cable connections.
However, Camera is the same color for both front and rear, so don't make a mistake. I installed it incorrectly and did not notice it until I tweaked the BackMonitor display. I didn't realize it until I installed it incorrectly and fiddled with the BackMonitor display.
I did not want to drill holes in the Motorcycle or put sticky double-sided tape on the Motorcycle, so I used the supplied Camera Bracket from DAYTONA and fixed it via the existing bolt on the Motorcycle. The inner diameter of the DAYTONABracket was a little wide, so I cut a rubber plate into strips and inserted it between the bracket and fixed it in place. As a result, I think it also prevented slipping and vibration.
This product is available in a range of Quantities:The set is set, but the mount for fixing the Body is no good and unusable.
Even though the body has a beautiful appearance, it will probably be scratched or damaged by the direct contact with the gold part of the mount. The mounting area on the motorcycle side is also likely to be scratched. Therefore, I decided to fix it with RAM Mount, and the additional expense was a little painful.
The Instruction Manual is translated (please enter your input here), but it is a strange translation and phrasing that is common in CHINA products, so if you really look at it, it will make you feel uncomfortable. However, the operation can be done intuitively, so there is no problem.
The GPS Sensor was placed upside down right under the Headlight, but it is functioning without any problems.
The color of my Motorcycle looks like OEM parts, and I don't feel any discomfort.
You can also view videos on Body, but it is convenient to download KYCAM2 (successor to KYCAM in the Instruction Manual?) from the play store and view it on your smartphone. (the successor to KYCAM in the Instruction Manual?) downloaded from the play store and viewed on a smartphone, it is convenient to view images, the road (map) on which the vehicle is traveling, and the speed at that time all at once. The sound is also recorded reasonably well via REMOTE CONTROLLER. However, the sound of the Motorcycle's engine is louder.
KYCAM2 was kicked at first because my phone has anti-virus software, but after I allowed it and downloaded it, I am able to use it without any problem.
Side note:The
On my first touring after installation, I had a near miss with a car (elderly BBA) that ran a red light. Fortunately, it didn't turn into an accident.
Incidentally, the Number of that jaywalking car was also clearly visible.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-6R
I installed it for another car model.
I installed the ZX-12R with the Handlebar Up Type in TouringSpec. The mounting hole was made a long hole and the point where it contacts Napoleon-on-Mirror was shaved off. At first, the front camera was fixed under the ram air duct, but it felt uncomfortable, so we purchased a different model this time with the assumption that it would be modified. The size of the bracket is too large to be noticeable, but I personally like the design. The camera is made in China, so the camera mounting holes were also modified.
Well, it's like Parenthesis is good (laughs), it's self-satisfying.
View detail
Rigidity is high and functionality is fine. Resin texture is a little poor and has a lot of BALI.
[How is it used?
CameraMount for Smartphone and Circuit driving.
Was the installation difficult?
It is not difficult, but it is a little unfriendly because it arrives in RoseRose without any Instruction Manual or anything. American in that area.
How was your experience with it?
The rigidity is high, and as long as you use a well-fitted ball joint, there is no rattle or wobble at all.
The surface finish of the resin is rough and there are still some BALI and cut marks from the manufacturing process. I was concerned about it, so I used File to break it in. I feel American in this area as well.
[Included Parts:were they on?
All included.
No Instruction Manual.
[Was there anything that disappointed you?
Roughness of resin surface finish.
Point and hang of installation
If the ball diameter is not a good fit, it will wobble.
Some similar looking products may or may not be Ram Mount compatible, so it is best to check for compatibility when purchasing.
View detail
If your phone is Waterproof Type, this is the one. (Spring & Autumn)
There are many different products available, but I feel safer with a physical full Hold. Furthermore, in spring and summer, I am concerned about my phone running out of heat, so I feel that the Type with wind exposure is better. I use it with the Option product for vibration protection. View detail
Fits: HONDA MSX125SF, HONDA CRF250RALLY, HONDA GROM, HONDA MSX, HONDA PCX150, HONDA PCX160, YAMAHA NMAX125, KAWASAKI Z125PRO, KAWASAKI D-TRACKER125, HONDA CRF250L, HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA Dunk, HONDA MAGNA50, KAWASAKI KSR110PRO, HONDA SUPER CUBC125, YAMAHA XTZ125, YAMAHA SEROW250, HONDA SUPER CUB110, HONDA LEAD125
Good work.
The texture is good.
It is very good compared to the Chinese products on Amazon.
A little expensive, but I can recommend it!
View detail