Reviews
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Refreshing.
I am happy to be able to install the DriveRecorder-Body without having to worry about where to place it.
It is Stage of Exactly on Body.
View detail
Used as Bracket for Switch on Grip heater
The Bracket that was originally attached was too long and was bent at the Prank, breaking it off at the base.
This time, I don't think it will be tampered with because the base LARGE size and height of the base are just right and not uncomfortable.
View detail
MITSUBA Dora Recording Essentials
The REMOTE CONTROLLER installation of the MITSUBA DRA RECORDER is the only choice, and the Fit feeling is unquestionable, but the price is high. View detail
Only for car model-specific
I had a DOREMI Emblem, but when I installed the DriveRecorder, I bought this and replaced it with a PMC Emblem.
The mounting position and angle of the Emblem and Camera were also to my liking.
Quantity of Bolts required to install the Emblem and Camera in the car model Exclusive Design.:I appreciate the fact that it is a Set.
View detail
I would recommend it.
I had always wanted to install PMC's Stem Steel Emblem, but I had given up because I had installed a DriveRecorder when I took delivery of the car.
I found this product and bought it immediately, Camera position was fine, easy to install, and I am satisfied with the large change.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Performance as expected.
The OEM Handlebar of the Z900RS does not need such a Mount Bracket bar, but a separate handle, etc,
This is necessary when the product becomes an Other Brand Product, such as when the handlebar is replaced.
If it is installed as shown in the photo, it is too close to the Tank, so it is better to install it in the opposite direction from the photo.
View detail
It interferes with the Fender Eliminator and is unusable.
In the picture it looked like it was attached to a Fender Eliminator on a Z900RS, so I bought it thinking I could attach it without any problem.
However, in reality, as shown in the photo, the angles do not match and there is too much interference, making it unusable.
There are a wide variety of Fender Eliminators for the Z900RS, but mine is an Active product.
Active's Fender Eliminator differs from other Manufacturers in the number angle and the distance between the Lamp and Number.
I think it's because of the proximity. But Active's Fender Eliminator is the most beautiful because there are no weird gaps.
I'm not sure if I should return it.
If you are a Fender Eliminator and the Lamp and License Plate are close to each other, please be careful.
View detail
Not for use with Stainless Steel Hose
I have a Stainless Steel Hose from Swage line and could not use it due to interference.
I could have used it if it had been directly below without the odd Offset...
I think the OEMHose is SMART and easy to install.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
this one option
Without much choice, this will be the one.
HolderQuantity:2pc. It is so long and convenient that USB is also attached to the Set.
It is being used with SP CONECTO and DAYTONA USB-A.
View detail
Would you prefer a little further back?
I have no problem with the overall construction, but when I put it on, the Emblem looks a little far away from the Fork, so I would have liked it to be a little shorter. View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 400 (2014-), KAWASAKI Ninja 250, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
Interference between meters and smartphone navigation is eliminated and eye movement is reduced, making it more comfortable.
I use a Smartphone for navigation. In the past, the Holder was attached to the Handlebar by touch, but when the screen was positioned for easy viewing, it inevitably overlapped with the Meter. By attaching this product to the Mirror Hall, I was able to adjust both the Meter and the screen to a position that was easy to see, and by reducing the amount of eye movement, I think it has contributed to improved safety. The product did not rattle when driving on paved surfaces, and the bolts did not loosen, but just to be safe, we used screw locks to prevent them from loosening after the location was decided. View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
I can't wait to use it in Touring.
[How is it used?
Mainly to attach a Smartphone Holder for navigation when touring. In the future, we plan to attach a go PRO and a power supply.
Was the one you received as per Image?
Stable as per Image.
How was your experience with it?
I haven't run it yet, but it is easy to see and Firmly fixed in the middle.
Previously, it was attached directly to the handlebar, so it was difficult to adjust the angle, but now it is easy to adjust.
[Points to note]
Since it is attached with a Handlebar Fixing Screw, it is basic but important to tighten the Screw from the front and to lay down a Towel to prevent the Tank from getting Wound during the work. It is not difficult if you have the right tools.
How did it compare to other products?
Not compared to other companies, but the longer width makes it easier to use.
Incidentally, the Smartphone Holder is made by DAYTONA.
View detail
The handlebar area is beautiful and looks great!
The fit is so good that it could be handled as an OEM product by Mistuba Sankowa, a manufacturer of digital camera systems.
The handlebar area is beautiful and looks great!
By the way, my mounting position is on the Clutch Side because the Button is only used for manual recording of the EDR-22G (one press for 20 seconds of manual recording) and also for emergency Brake operation.
View detail
Change from Front fork installation Type
This is a change from the Front fork installation Type. The appearance is also refreshed. However, the bracket of ForkEmblem and this bracket partially overlap, so it is necessary to install the driver's recorder first. The angle could be adjusted after installation. It might be easier to install without the additional Type. View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Installation is easy
There is nothing difficult about the installation.
Before the work, the tank is cured with a thick toweletc. to prevent wounds.
(It's just a small step to avoid the extra time, effort, and expense.)
1.Temporarily assemble the Mount Bar and Mount Bracket.
2.BoltQuantity near the tank of the Handlebar Holder:Remove 2pcs.
3.Assembled the collar, temporarily assembled Mount Bar + Mount Bracket, Flat Washer, and M8x45Cap bolt to the car body in this order.
4.Temporarily tighten Bolt on each part
5.Bolt tightening in each part
This completes the process, but there is one point to note.
Tightening torque for M8x45 cap bolt. The specified tightening torque in the Instruction Manual for the product is 30 N・m, and the same value is given in the Service Manual. However, do not tighten the bolt all at once, but tighten it while observing the situation.
The tank-side joint surface of the upper handlebar holder has a gap with the tank-side joint surface of the lower holder. Since the upper holder is cast aluminum, it may break when tightened in overtorque.
The appropriate tightening torque varies depending on the bolt material, strength, material to be fastened, required fastening force (axial force), etc. Of course, there are standard tightening torques. Of course, there is a standard torque for fastening.
Since this is an important part of the steering, we recommend the use of proper fastening tools and not relying on intuition as much as possible.
The same situation may not apply to other vehicles of the same model and year.
To be sure, we checked the torque of the Handlebar Holder Fixing Bolt on the actual vehicle before disassembling.
All four were 20 N・m without lubrication. The target for Torque tightening was 20 Nm.
In the photo, both the cap bolt and button cap bolt are black.
This is because we changed the color when we changed to the same material as the OEM Handlebar Holder Fixed Bolt.
The OEM Bolt is SCM435 (10.9T) trivalent ChromateWhite.
The Bolt in the photo is SCM435 (10.9T) trivalent ChromateBlack.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 250, KAWASAKI Ninja 400 (2014-), KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
Color and shape are both GOOD!
NINJA2 Helmet50R (Kawasaki Ninja series) is the best part of Parenthesis.
The top bridge and meter area are cut out.
I didn't want to hide it with Mount Bracket or my phone.
In addition to the Top Bridge, it can be attached to the side of the Separate Handle.
I was looking for something like the Short Bar and found this one.
I wanted to unify the Handlebar area with Red, so it was nice to have the Red color option.
I installed the ETC sensor (?) at the clutch lever. I tightened it to the bracket where the ETC sensor (?) is installed.
It was difficult to adjust the angle.
The first time I cut the Handlebar all the way to the Right with the phone attached, I damaged the Screen.
I was careless.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 250, KAWASAKI Ninja 400 (2014-), KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
When attaching a Bracket to a Motorcycle with a Separate handle
[How is it used?
Used to mount the Smartphone Mount on the Separate Handlebars of Ninja 400.
Was the installation difficult?
On the Ninja 400, there is an unused screw hole in the clutch lever that can be fitted in a matter of seconds if you have a Hexagonal Wrench.
How was your experience with it?
This is the only bracket that requires a screw hole conversion adapter.
I think it is good to be able to choose your favorite color because there is a color development.
[Was there anything that disappointed you?
The Handlebar area is a bit cluttered, as is the rest of the Bracket and the Multi Bar, and it's quite noticeable when you're trying to mount your phone from the Bracket.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 400 (2014-), KAWASAKI Ninja 250, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
Mmm.
I put it on my current NINJA400, but the angle is not level because it is installed in the mirror hall of Handlebar, and the inside is facing up, so when I install a smartphone or Beeline Moto, the screen is facing outward and I can't see it unless I look into it. The design and color are good, but from a functional standpoint, I'm not happy with it. View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Very good!
Installation is easy
The texture is not bad either.
If the phone is mounted in the middle, it will be in the way when inserting the Gasoline. (Lol)
As long as the phone is on its side, I don't see a problem...
Overall, I'm satisfied.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 400 (2014-), KAWASAKI Ninja 250, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
for little things
I chose this product to add to my Handlebar Par because I couldn't add anything else to it.
I love the size and the shape!
View detail