Reviews
Recommendation for those who are anxious to draw a Maintenance Stand alone!
Although an instruction manual is included, it does not explain the details of how to assemble the unit, which was confusing at first. I would have liked to have a guide to the screw holes to be used for the approximate number of inch tiers.
There was a product video on how to use and assemble the product, so I checked it out and assembled it. The video was very helpful.
The NINJA1000's front tire (120/70Zr17) was firmly secured and stood on its own. It also felt stable when lowering the bike.
I used to do maintenance only with the Rear STAND, but when I lifted up the bike by myself, I didn't hang it properly and it fell over. I wish I had bought it before I stumbled...I would like to recommend this product especially to those who work alone to avoid damaging a large motorcycle.
View detail
Feeling of security
I always had a hard time hanging the Maintenance Stand on the Swing Arm, but by fixing the front tire to the ClampSTAND, the stability is increased and the Maintenance Stand can be used with ease. View detail
Rear stand hanging is easy
I found the product by chance, searched for it on Webic and bought it. It is super easy to hang Rear stand especially in Garage. I wish I had bought it from the beginning. I highly recommend it. View detail
If it were a little cheaper, there would be a reason to choose it.
[How is it used?
Purchased for storage and maintenance of Dual PurPass vehicles.
I already have a Lift Stand made by DRC, but I bought an additional one because I use it for storage of another vehicle in my garage. I'd like to compare it with the DRC one.
Was the one you received as per Image?
I don't know which Manufacturer was the first to market this type of product, but I think DRC is the MAJOR MANUFACTURER in the STAND of LiftType with Damper? I think so.
PROTOOLS' Lift Stand is a "DRC+AstroPRO Ducts÷2" The product is functional and just like the Image, although there are some parts where the system is a bit....
Was the installation difficult?
The body and lever part, which is lifted by the principle of leverage, arrive in the box in a pre-installed state, so after opening the box, the body is assembled with two Bolts & Nuts.:Pair (for Left and Right) Bolt did not go into Smooth due to a subtle Gap in the
I used a round bar File to slightly enlarge the hole, but I think this is an individual difference, so I don't think all products have gapped holes.
How was your experience with it?
The vehicle is almost vertical and stable after lift up with less rattling at the props than with DRC products.
Since it has only been a short time since we purchased it, we have not experienced any Damper gas loss, and there is no functional inferiority compared to DRC products, and we hope that the performance will be maintained for as long as possible.
The rubber mats on the ceiling, which are grounded to the vehicle, are fixed to the top panel with thicker Rivet, but in terms of visual quality, they are inferior to those made by DRC.
[Was there anything that disappointed you?
I don't think it is a disappointment, but the paint on the lever part of the leverage is easily peeled off, so it might be better to handle it carefully, apply protective tape, or repaint it, as the base is exposed when it is raised and lowered roughly.
Other items that would be helpful
Point and hang of installation
If each moving part is thoroughly greased up before use, wear and force on moving parts can be reduced, so it is a good practice.
Quantities like the one I purchased:Pair (for Left and Right) Even if there is a gap in the screw hole of a screw, it is easy to rework it, so do not panic and check each part after temporary assembly.
[Availability and clarity of the Instruction Manual
It contains only a very simple installation instruction manual like a memo, but I think it is an easy-to-understand product for its intended use.
[Notes]
When lifting up, use the carBoth Sides of the car where the ground surface is as flat as possible.
Lifting up on an uneven surface can cause the vehicle to become unstable and fall over, damaging or injuring the motorcycle.
Also, be sure to lock the lock lever after lifting up.
Please make sure to check the lock to avoid the risk of accidentally touching the lever of the leverage part and causing the motorcycle to come down.
[ITEMS TO BUY TOGETHER
If you do not have Grease as a maintenance tool, purchase cheap Grease and apply it to the moving parts during assembly.
[Opinions and requests to Manufacturer
To be honest, there is not much price difference between this product and the one made by DRC. "Sell" If you pay a little more Gold, a real (?) DRC will replace it. If you pay a little more Gold, you can replace your DRC with a real (?) DRC.
I would not say half the price, but a price about 4,000 yen lower than that of the DRC product would be attractive enough.
View detail
Convenient for both ChainMaintenance and Wheel cleaning
These are the useful items that impressed us the most after we started to ride motorcycles. Especially for those of us who started our motorcycle life with Belt-driven motorcycles such as Buell and Harley, Chain maintenance has been a great hassle since we started to ride Chain-driven motorcycles.
I was very impressed when I found this maintenance stand, and it made it very easy to clean the wheels and check for nails and other foreign objects after driving. Moreover, even with a Harley Ultra weighing nearly 400 kg, it was not particularly difficult to put it on the stand, and it is a supreme product that is very easy to put on and take off.
View detail
Front Wheel Stand
Until now, I have been doing maintenance in the garage using only the jTrip Rear Stand, but now I can easily raise the Rear Stand with one hand after fixing it with the Front Wheel Stand.
It is very convenient and quite stable in the upright position.
Someday in Transporter …
I have all kinds of fantasies, such as.
It takes some force to push and pull, but once you get used to it, I don't see what the problem is.
I should have bought it from the beginning.
View detail
Easily Chain Cleanable! But there are better products out there.
As the title says, a motorcycle novice I want to clean Chain!" then it occurred to me
It is good to buy and use.
However, once you gain some experience and know the existence of various products, you will stop using them;
Specifically typhoon-proof and portable. Unit." products and
If you want to use it for more serious maintenance, you should purchase MaintenanceSTAND.
In terms of the first step of maintenance, this product can be recommendation.
View detail
If you use the Rear stand alone, it's a must!
I use several of the same STAND, but Large is convenient.
Can also be used for 21-inch Wheels if forced.
The slender Tire falls over, so a rearward Jack-up or Lift-up is immediately necessary, but if you understand the precautions, it is a Large-change convenient Clamp.
The CHINA packaging arrived with the STAND exposed upon delivery.
Points will be deducted for numerous scratches and color peeling.
View detail
Convenient
Convenient for cleaning the rear wheel and maintenance of the drive chain.
Chain can be cleaned very easily without Center Stand.
View detail
Triangle section is long and Motorcycle is not slanted.
Because the Triangle section is long, the Motorcycle is not slanted and will fall to the opposite side when the wind blows.
It is completely useless for both 18-inches and 19-inchesTire Racer.
I had to repurchase another product.
The Triangle seems to be about 1cm longer than the normal one that was repurchased.
View detail
It can be used, but only in Large size.
Cost performance is sufficient. However, care should be taken when using it on heavy motorcycles. The clearance of the support part is large, so it will be slightly slanted. We own an NSR250R and an NSR50, and it can be used for both. Both vehicles are lightweight, so even if it is skewed by hand, it can be corrected. View detail
For motorcycles that don't have a center stand.
Useful for cleaning the rear wheel and Drive chain, reducing chain cleaning and grease up maintenance time, and is a must-have item for any motorcycle without a center stand. View detail
I've been using it for a while, but...
It is good for ChainMaintenance and so on, but the drawback is that it is heavy, and the adjustment is necessary because the Gap comes gradually as the tire is turned, and it is troublesome to put the tire on every single time.
Also, it takes a bit of effort to rotate the Tire.
It's not bad, though.
Right now I'm using a lightweight Compact and easy Unit.
View detail
Good stuff
I bought this to maintain my motorcycle's front and rear wheels It should be lifted up with front and rear STAND, but I did not have to remove the Tire It is inexpensive and effective enough for cleaning purposes
However, if you don't let the Roller have Tire orthogonal to the Rollers, the Gap is gradually reduced as you rotate it You need to be careful when you put the Tire on it
View detail
ChainMaintenance is on its way!
The other day I used it for maintenance of the undercarriage, and the Tire rotates smoothly I was able to work efficiently with the
Because the body of the car is at an angle, the Tire is the Quantity:Pair (for Left and Right) There was no particular inconvenience to Slide to
I wish I'd bought one sooner, because up until now I've had to move the body back and forth to work on it!
I have no problems with the texture and quality
View detail
It is useful unexpectedly
It is C650 GT, but Rear is good because there is a Center Stand, but Front
When washing, I found something good with internal medicine
It is unknown whether it can be used at 120 - 70 - 15 at the inquiry stage
Although it was thing, it was easy to say
In addition I could also use MONKEY w
If it says strongly, the bottom Rubber shifted soon, but I do not mind it
It does not get in the way of it, it is better to use something quite useful
View detail
Speaking of easy handy
I usually use Maintenace Stand, but since I made it damaged from a slight carelessness, I tried purchasing this item I was curious as before as a connection until I repurchase.
According to the conclusion, it is like the price is suitable.
I think how to compare it with Maintenace Stand, but again it is very heavy to turn the Tire and the workability is not very good.
Also, as the other people say, the position shifts while turning the Tire, so stand up the car etc etc. We need some kind of countermeasure.
However, it does not take up space for storage and does not Lift Motorcycle, so there is almost no Risk to overturn accidentally, and Merit says that prices are cheaper than anything.
However, if it was not discounted and sold at fixed price, I think that you should buy Maintenace Stand from here ...
If you are ChainMaintenance who moves the body forward and backward, I think that it may be good to try purchasing it once.
This time, only rear. I used it for Front, but I would like to use it later.
View detail
It was good not to be STAND
I was worried about Rear stand in Maintenance of Chain but I bought it because the price is cheap.
Although it is not possible to turn around the corner, it turned around more lightly than I thought.
It seems that the cost effectiveness is high.
It did not have to be an expensive Rear stand!
View detail
Easy ChainMaintenance
ChainMaintenance of lifting and moving Motorcycle is bothersome because it is troublesome. It was very easy to turn Tire if Motorcycle weighing less than 200 kg. You can use it even with the car of Lock tie's Off. Even if things are small, it is light so you do not have to get in the way.
The price is also reasonable.
Because I am concerned about durability because it is Made in China -1 ☆
View detail
After moving out the apartment, the place was narrow also for maintaining and purchased for the Chain Maintenance to also maintain. Comment used for a 250-cc Motorcycle. Although it is troublesome too compared with the Maintenance using the
After moving out the apartment, the place was narrow also for maintaining and purchased for the Chain Maintenance to also maintain.
Comment used for a 250-cc Motorcycle.
Although it is troublesome too compared with the Maintenance using the
Maintenance stands, I think that he buys it and there is no loss if it is a direction of the same environment.
Compared with the Maintenance stands, a price is also handy.
View detail