Reviews
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Refreshing.
I am happy to be able to install the DriveRecorder-Body without having to worry about where to place it.
It is Stage of Exactly on Body.
View detail
Used as Bracket for Switch on Grip heater
The Bracket that was originally attached was too long and was bent at the Prank, breaking it off at the base.
This time, I don't think it will be tampered with because the base LARGE size and height of the base are just right and not uncomfortable.
View detail
Compact Cargo Hook
It does not protrude more than the Clubba and fits better. The Net Hook should be more compact to fit in the case of the Clubba. I used the same Posh face color SpoolM8x30mm and Stainless boltM8x105mm. View detail
MITSUBA Dora Recording Essentials
The REMOTE CONTROLLER installation of the MITSUBA DRA RECORDER is the only choice, and the Fit feeling is unquestionable, but the price is high. View detail
Loading Hook
A Loading Hook has been added for easy use of the Net to supplement the capacity of the Small TypeTank Bag. On the back side, a Loop is threaded through the Club bar.
I used the same Posh face colored Spool M8x30mm and Stainless bolt M8x120mm as the Loading Hook without any modification. I think a M8 x 25mm colored spool or a 1cm short Loading Hook would have been fine. However, in the case of the Short Hook, the inner diameter is too large to interfere with the Club bar, and a thin Hook made of gold might be better suited for this purpose.
View detail
Only for car model-specific
I had a DOREMI Emblem, but when I installed the DriveRecorder, I bought this and replaced it with a PMC Emblem.
The mounting position and angle of the Emblem and Camera were also to my liking.
Quantity of Bolts required to install the Emblem and Camera in the car model Exclusive Design.:I appreciate the fact that it is a Set.
View detail
Used as anchor bolt for REBEL250
It was used as an anchor bolt for REBEL250.
Recent Motorcycle has no Loading Hook because of CostCut.
It will be installed as a retrofit, but the car-specific products are quite expensive,
We think it is a good idea to use such a Universal Product.
This product comes with a 30mm Bolt, but with a slightly shorter exit allowance,
A separate 35mm Bolt will provide the same amount of output as the OEMBolt.
(Even Bolt with "Included Parts:" can be used as long as it is firmly tightened.)
One note on installation.
For OEMBolt, after removing one part, temporarily fasten this product and then remove the next part.
If you remove the Bolt holes in two places at the same time, the Bolt holes will shift, making it difficult to install and licking the Screw holes.
Also, the OEMBolt is tightened at a ridiculously high Torque, so it is hard to loosen the Bolt.
If you find it difficult, you should honestly ask Shop for help.
View detail
I would recommend it.
I had always wanted to install PMC's Stem Steel Emblem, but I had given up because I had installed a DriveRecorder when I took delivery of the car.
I found this product and bought it immediately, Camera position was fine, easy to install, and I am satisfied with the large change.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Performance as expected.
The OEM Handlebar of the Z900RS does not need such a Mount Bracket bar, but a separate handle, etc,
This is necessary when the product becomes an Other Brand Product, such as when the handlebar is replaced.
If it is installed as shown in the photo, it is too close to the Tank, so it is better to install it in the opposite direction from the photo.
View detail
I am concerned about Bolt's Size.
Here are my impressions after installing on a Triumph SpeedTWIN1200.
Since there was no place where a Net could be attached, it was installed in the form of replacing the Bolt on the Rear suspension.
The work was easy and securely installed, and the Net is now ready for use.
Also, the texture is adequate for the price.
I bought Black, and if I wanted, I would be happy if the center Bolt was also Black.
Bolt size was a concern during installation.
The length was fine, but the diameter was slightly smaller than M8, and I was a bit concerned about the possibility of the mountains licking if I tightened the screws too hard.
(It may be correct to say that the Frame side may be just slightly larger than the M8, so it is not an outstanding match when installed on SpeedTWIN.)
I'm generally satisfied.
View detail
It interferes with the Fender Eliminator and is unusable.
In the picture it looked like it was attached to a Fender Eliminator on a Z900RS, so I bought it thinking I could attach it without any problem.
However, in reality, as shown in the photo, the angles do not match and there is too much interference, making it unusable.
There are a wide variety of Fender Eliminators for the Z900RS, but mine is an Active product.
Active's Fender Eliminator differs from other Manufacturers in the number angle and the distance between the Lamp and Number.
I think it's because of the proximity. But Active's Fender Eliminator is the most beautiful because there are no weird gaps.
I'm not sure if I should return it.
If you are a Fender Eliminator and the Lamp and License Plate are close to each other, please be careful.
View detail
Not for use with Stainless Steel Hose
I have a Stainless Steel Hose from Swage line and could not use it due to interference.
I could have used it if it had been directly below without the odd Offset...
I think the OEMHose is SMART and easy to install.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
this one option
Without much choice, this will be the one.
HolderQuantity:2pc. It is so long and convenient that USB is also attached to the Set.
It is being used with SP CONECTO and DAYTONA USB-A.
View detail
Would you prefer a little further back?
I have no problem with the overall construction, but when I put it on, the Emblem looks a little far away from the Fork, so I would have liked it to be a little shorter. View detail
Mounted on KTM 250 ADVENTURE
Replaced with Inner fixed Bolt by Tail Cowl.
Since the KTM 250 ADVENTURE does not have any kind of Loader Hook, we will use the MOTOFIZZPlate hook3 and the DAYTONATouring hook as a loader point to be used together.
The 25?Cap bolt that came with it was usable as is with no length issues.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 400 (2014-), KAWASAKI Ninja 250, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
Interference between meters and smartphone navigation is eliminated and eye movement is reduced, making it more comfortable.
I use a Smartphone for navigation. In the past, the Holder was attached to the Handlebar by touch, but when the screen was positioned for easy viewing, it inevitably overlapped with the Meter. By attaching this product to the Mirror Hall, I was able to adjust both the Meter and the screen to a position that was easy to see, and by reducing the amount of eye movement, I think it has contributed to improved safety. The product did not rattle when driving on paved surfaces, and the bolts did not loosen, but just to be safe, we used screw locks to prevent them from loosening after the location was decided. View detail
PoshNet Anchor
I bought it because I like the color. The paint has not peeled off so far. View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
I can't wait to use it in Touring.
[How is it used?
Mainly to attach a Smartphone Holder for navigation when touring. In the future, we plan to attach a go PRO and a power supply.
Was the one you received as per Image?
Stable as per Image.
How was your experience with it?
I haven't run it yet, but it is easy to see and Firmly fixed in the middle.
Previously, it was attached directly to the handlebar, so it was difficult to adjust the angle, but now it is easy to adjust.
[Points to note]
Since it is attached with a Handlebar Fixing Screw, it is basic but important to tighten the Screw from the front and to lay down a Towel to prevent the Tank from getting Wound during the work. It is not difficult if you have the right tools.
How did it compare to other products?
Not compared to other companies, but the longer width makes it easier to use.
Incidentally, the Smartphone Holder is made by DAYTONA.
View detail
The handlebar area is beautiful and looks great!
The fit is so good that it could be handled as an OEM product by Mistuba Sankowa, a manufacturer of digital camera systems.
The handlebar area is beautiful and looks great!
By the way, my mounting position is on the Clutch Side because the Button is only used for manual recording of the EDR-22G (one press for 20 seconds of manual recording) and also for emergency Brake operation.
View detail
Change from Front fork installation Type
This is a change from the Front fork installation Type. The appearance is also refreshed. However, the bracket of ForkEmblem and this bracket partially overlap, so it is necessary to install the driver's recorder first. The angle could be adjusted after installation. It might be easier to install without the additional Type. View detail