Reviews
The quality is good for the price.
Purchased for appearance improvement rather than effectiveness.
As a result, I am glad I bought it.
The appearance is as expected, the quality is very good for the price, and the effect is a little less slippery. The effect is a little less slippery.
If you want to do the work yourself, we recommend working with Tucker for a few thousand dollars.
The $800 Tucker I had at home did not stick deep enough.
View detail
For processing
Used for processing as Seat is too low for my height of 178cm.
Sponge is placed on top of OEMSeat and wrapped with this product.
Tucker is Large sturdy if you use a 100-unit item and hit it with a Hammer in places.
The seat surface is textured with a grippy material that is hard to slip on.
Minus is short and Limit in length in the front and back of the center.
View detail
This is for those who would prefer to change the Front but also want to stick to the Tandem seat.
I installed the Tandem seat because I wanted to be particular about the Tandem seat along with the Front Seat.
Stitch and stab color can be selected from four types [Red, Green, Black, Blue].
For the KRTEdition of the ZX-25R 22 MODEL, I chose the Red color because the Red color line extends on the body.
There are some people who have uploaded their front seat installation on YouTube, but I don't think there are many people who have changed the tandem seat as well.
[Regarding installation]
Tucker (like a commercial Stapler) is required.
As for Tucker, there are some 100-yen ones, but the ones that cost several thousand yen with Power are better.
Still, it is better to leave the installation of Seat to a contractor if possible, since it is difficult to stick in Seat Plastic.
[About the feeling of use]
It is a Tandem seat, so I don't know if it is hard to slip when sitting on it.
Tandem seatBelt comes with the same Stitch color as the one you ordered.
The Seat does not feel thicker when covered and can be used as usual.
I think most people who change to this Seat cover want to be different or to improve the appearance of their Parenthesis.
I think the product responds well enough to that.
LUIMOTO's seat covers are available for many manufacturers and motorcycles, so if you are interested, why not check them out?
Please note that since this is almost a made-to-order product, it will take one to two months after ordering as it is not likely to be in stock. (´・ω・`) b
View detail
If you want to make a difference and improve your parenthesis, by all means, go for it!
Stitch and stab color can be selected from four types [Red, Green, Black, Blue].
For the KRTEdition of the ZX-25R 22 MODEL, I chose the Red color because the Red color line extends on the body.
I have seen other people on YouTube who have had it (I have seen two KRTEdition people on YouTube who have had it, although the year is different). selected the color Green.
Well, that is my preference.
[Regarding installation]
Tucker (like a commercial Stapler) is required.
As for Tucker, there are some 100-yen ones, but the ones that cost several thousand yen with Power are better.
Still, it is better to leave the installation of Seat to a contractor if possible, since it is difficult to stick in Seat Plastic.
[About the feeling of use]
It feels slippery when you sit on it, but not that much to experience it.
The Seat does not feel thicker when covered and can be used as usual.
I think most people who change to this Seat cover want to be different or to improve the appearance of their Parenthesis.
I think the product responds well enough to that.
LUIMOTO's seat covers are available for many manufacturers and motorcycles, so if you are interested, why not check them out?
Please note that since this is almost a made-to-order product, it will take one to two months after ordering as it is not likely to be in stock. (´・ω・`) b
View detail
You can just cover it up.
The edge is Rubber, so you can use it just by covering it.
I used the Tucker because I wanted to fix it completely, and in that case, I removed the OEMCover because the crease on the edge of the OEMCover was in the way.
I'm worried that the rubber will loosen up when the seat is stretched.
Unlike the smooth OEMRear Sets, it is good to have detailing with different surface skin and Stitch.
View detail
DIY Installation
It was DIY enough to install, I used a Tucker from Daiso, 6mm replacement needles, Hammer and Pliers.
If you only use a Tucker, it won't stick deep enough, so you have to hit it with a Hammer, and sometimes it bends, so you have to pull it out with Pliers and start over.
It's easy to put it up because it has a lot of tension just by covering it.
However, I gave up trying to get a perfect fit because of the tight bend and almost no edge at the back edge.
If it stretches moderately, it does not become Wrinkle and the outline becomes uniform, so I fixed it in a good-looking position and finished it.
The seat has an uneven surface that gives it a luxurious grip.
The part that touches the inner thigh when the car is stopped is slippery Material:It is also good that it is made of Carbon Style fabric and has both design and function.
View detail
DIY Installation
It could be installed by DIY.
I used Tucker from Daiso, 6mm replacement needles, Hammer, and Pliers.
It is easy to put up because it has a lot of tension even if it is just covered.
If you only use a Tucker, it won't stick deep enough, so use a Hammer.
I couldn't stretch it perfectly at the hollow at the back end because the edge is too tight and there is hardly any edge.
However, if it is stretched moderately, it does not become Wrinkle and Line becomes uniform, so I fixed it in a position that looks good and finished it.
There is a sense of luxury, and the seat surface has a moderate uneven surface, so the grip feeling has been improved.
Material with a slippery outer layer on the inner thighs when the car is stopped.:It has Carbon Style, and it is good that design and function are compatible.
View detail