Reviews
Hole plugging!
Regardless, it is just a Bonsai Parts to fill the Screw hole!
But, well, I wanted to add some Blue color to it, so I went out and spent it....
View detail
Bar End
It must be cheap, but this is how it is. View detail
If it is a bit cheaper
It is a must have product to replace a different handlebar diameter, but a lower price tag would be better.
Also, if you could include a thin double-sided tape, it would make positioning easier.
View detail
It was a little long.
Changed to Long cable due to change to Handlebar Up Type. It is a little long, but there is no problem in use. Conversely, the Handlebar can still be raised.
Installation was troublesome with the carburetor part.
View detail
Convenient.
I was looking for it because I got bent out of shape standing up.
Separate handle category only by car model, and not in the Separate handle supplemental parts category.
If it only appears in the Handlebar category, it won't be found.
in a hurry
According to HURRICANE officials, the effective length of the handlebar differs for each car model.
CBR250R that turned. (MC41) Effective length 205mm for
The one I bought this time is the Universal one from for Repair, 217mm.
The former is a bit helpful because the Handlebar length is quite short and the Switch box was also Limit.
Incidentally, I asked HURRICANE officially if there was anything longer than this, and they said this is the longest.
I would like to see the information properly posted by car model if possible, though.
It's not so friendly, though, because it's often out of stock, and the model number is not listed in the official HURRICANE website, and it's hard to find the official HURRICANE website in the first place,
The angle can be easily adjusted, the holder is strong, and as long as you have the holder, you can use it in any way you want.
View detail
I'm glad it's rust resistant!
I used it to replace Mirror on an AddressV125 that a friend gave me! It works normally!
It would be nice if the design was a little more unique or better made!
View detail
It was a little long for me.
[How is it used?
After six months of hanghang and Restore&Custom work on the LITTLE CUB, I thought I'd get comfortable with the next stage of the project. First, we need an external power source. I started looking for a USB power supply, but realized that there was no place to install them, so I looked for a Mount Bar in Webike's product introduction section and bought a Multi Bar from Made by HURRICANE, which had a safe design.
How did you like it?
Although I knew it existed until now Messy around the Handlebar. The Mount bar had never been used before because I had the impression that it was too heavy.
The fact that I had a safe length and design for my first Mount bar purchase and I was a teenager. Separate handle (Handlebar of Separate type)". Speaking of Other Brand Products of "HURRICANE It was an Image that I was not surprised to see. Finally, I too will buy HURRICANE products." I bought the Multi Bar at Tension...but the bar was a little too long for my use.
Please don't get me wrong, the product itself was a good product with good rigidity, but for my personal use, I would have preferred a shorter length, so after much thought, I replaced it with a Mount bar made by another company.
We wanted to use a Short Type Mount Bar to make it as Refreshing as possible, since we only need to be able to fix the USB power supply and Smartphone Holder.
How did it compare to other products?
If it is a MAJOR Manufacturer's product. "A damned glitchy piece of junk." I don't think there are any.
Before you buy Which car? of Which part? and there you want to install it in What do you want to install?" I think that Risk can be reduced if you take into account the following before making a purchase.
[Points to note]
This product is a type that is attached to the Mirror Holder by fastening it to the Mirror Holder, so it is easy to set the quantity to a position that is easy to use.:Once set, please tighten and secure each part firmly, otherwise you will be in a hurry if it loosens while driving... (This is a testimonial.)
Other items that would be helpful
The deciding factor in the purchase
As I mentioned above, I didn't even understand the difference between the Mount bar and I didn't think it through. HURRICANE Products I bought this product only because it was a very solid product with no fault of this product over and over again.
【Included Parts:presence or absence】.
Bracket for connecting Mount Bar Body and Mirror Holder, 2 Washers and Spring washerQuantity:1pc. and Nut included.
[ITEMS TO BUY TOGETHER
Products to be installed on Mount bar.
If you purchase the products you want to install at the same time, such as a power supply outlet, Smartphone Holder, Drink Holder, Camera Mounting Holders, etc., you can proceed with the work at a stretch.
Opinions and requests to Manufacturer.
It resonates with my father's generation. "HURRICANE BrandName, we look forward to continuing to serve you with a variety of custom parts at affordable prices.
View detail
Fits: YAMAHA SR500, KAWASAKI ZEPHYR750 RS, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, YAMAHA SR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR400χ
It makes you look pretty.
I think the price is reasonable and it is a good product for casual makeover. I think it looks cute.
Installation was a little difficult in positioning.
The drawback is that the LightBody of the car body gets small scratches at the installation pin if the positioning takes too much time and has to be redone.
Rather than putting it on and taking it off, it might be better to leave it on after putting it on.
View detail
Fits: HONDA APE 100, HONDA GB250 CLUBMAN, HONDA APE 50, HONDA APE 50, SUZUKI GRASS TRACKER Big Boy, YAMAHA SR500, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW225E, SUZUKI GRASS TRACKER, Others , YAMAHA SR400, HONDA MONKEY, YAMAHA TW200, HONDA FTR223, HONDA FTR223
Caution when installing
It is an inexpensive product, and since it is made by a long-established manufacturer, there should be no problem with the quality of the handlebar.
Two requests for improvement.
(1) The paint is too soft and just a slight touch will cause wounds. (2) Extreme care must be taken when installing this product.
I would like the center mark to be engraved instead of Sticker, because Sticker is too hard and peels off easily.
View detail
ticklish
When installed on a W650 external Handlebar, it feels like it has gone from brung to PullPull.
My wrists felt slightly ticklish throughout.
Better than painful, but I have some concern about what happens to people when this tickle builds up over long distances.
View detail
Fits: KAWASAKI BALIUS2, KAWASAKI BALIUS, KAWASAKI ESTRELLARS, KAWASAKI ESTRELLA
Not as good as OEMs
Even though I tightened it on the meter gear side, there was a small gap, so I installed it with an O-ring over it to prevent water from getting in.
I think OEM is the best choice for Speedometer unless you are concerned about Mesh.
View detail
Fits: KAWASAKI ER-6n, KAWASAKI NINJA400 (2014-), KAWASAKI Ninja 650
Fender Eliminator Kit
It arrived earlier than I expected, which was a big help. The instruction manual for installation is difficult to read … I thought it would be better to make it a little larger. I am very happy with the quality of the product and the price. View detail
Necessity for Handlebar replacement!
[How is it used?
Street Riding and Touring
I purchased this product because the OEMWire is no longer available due to the replacement of the Handlebar.
Used for FCR Carburetor Body.
Was the one you received as per Image?
It was just as Image.
Was the installation difficult?
Wire needs to be removed and adjusted. If you are familiar with maintenance, this will not be a problem.
How was your experience with it?
Accuracy and quality on par with OEM. The outer membrane is soft and easy to handle.
[Included Parts:were they on?
This product only.
[Was there anything that disappointed you?
None
Other items that would be helpful
important point
Please choose the corresponding Wire for your car model.
Opinions and requests to Manufacturer
I would like the length of the external membrane and Wire to be listed for each.
View detail
When was the last time you dropped out of a replenishment?
I bought these caps because the caps on my Handlebar Clamp Bolt had fallen off before I knew it, and the price is great for a pack of 12. View detail
BALIUS2Pillion Bar
Installation was easy and looks great!
However, the Seat is difficult to close and the Seat interferes with the Bracket of the Pillion Bar, causing the Seat to tear.
View detail
In truth, it may be royal to ride as Original….
I bought it to change the position. The actual difference is slight (3cm up, 3cm back, width −6cm), but the feeling has changed a lot. It had been half a year since delivery and I was just getting used to the lower position, but now that it is a little higher and in front of me, the pain in my palm from over 50 km has lessened.
I don't think the appearance has changed that much. I originally liked the cafe's style, so I was glad that the design did not change. It's subjective, but ….
I know, but I personally prefer the Matte Black color, which is the same as the OEM, because the color is shiny and shiny paint. (I guess I just don't know about them …)
Note - I purchased a part to widen the width, but it is undeniably ugly, as it would require structural modification.
Incidentally, when we asked the labor charge for bringing in the parts to our neighbor's shop, they told us that it would be 17,600 yen if the clutch wire is replaced (this is a telephone inquiry, so please keep it as a reference). (This is a telephone inquiry, so please keep it as a reference only.) I tried to do it by myself, but it took a long time because I am not used to it. I recommend that amateurs ask a motorcycle shop to do it.
Conclusion - I was accustomed to a low Position, so my impression is that it is just a taste change, but I think it fits the Japan human body type.
View detail
Is it no wonder it bends so easily….
I am using it on a HRC Grom jc92 and the Switch box interferes with the Shroud unless I add a Handlebar Stopper.
I use the 4th one because I prefer the Position I get with the Handlebar in Kochira. The reason why I use the fourth one is that it bends easily even after a light fall during a practice run. It would be nice to have a little more strength.
Well, I'm just saying, as long as you don't mock it up (laughs).
View detail
I would like to see an assortment in 5 cm increments.
Purchased to change the OEM Handlebar of a MONKEY125 to a Handlebar Up Type.
I bought a 200Millimeter long, but I really wanted a 150mm longer one.
No complaints about the feel of the product. 。 Sliding was good even without going through Oil.
View detail
subtle
No quality problems.
I think we have different tastes.
I have the Position set so far forward that it looks a bit Mischief, but this would be closer to my best preference if the Edge angle were just a bit shallower.
The wires are thinner than OEM, so they require additional parts, but only the clutch wire needs to be replaced. The rest was OK with OEM.
View detail
It was short
I found this item, new and unused with exterior pain, at a used Parts store and purchased it.
I tried to put it on a WR250X that I replaced with a Taper Handlebar, but it was too short for SSize.
I use only Clamp and use Shaft as POSH.
I did not feel any vibration reduction.
View detail