Reviews
Different products
I selected t2Type and received the wrong item. I emailed the contact and got no response. I don't know how to return it.
What is going on?
View detail
Brake hose
Because the dimensions of the product were not written, it was written for Eliminator 400se but did not meet.
Please fill in dimensions, OEM Product No., etc. I bought the wrong product.
View detail
Instruction Manual is first of all a liar.
The Instruction Manual says that the torque for tightening the included banjo bolt is 18 to 20, but in reality, the bolt is twisted off when tightened at that torque.
Buyers should take note.
View detail
I really, really want my time back.
I purchased this for my HORNET 250.
Overhaul MASTER and Caliper both front and rear while replacing.
I started with the Rear, and when I tightened the Bolt, the Aluminum Washer was ripped off and was useless.
I changed to Copper Washer and tightened it again, but this time the Aluminum Banjo Bolt shredded.
As for the banjo bolt, I guess it's my lack of Torque management.
As for Washer, it is clearly not strong enough.
If you are purchasing this item, we recommend using the Copper Washer instead of the included Aluminum Washer.
Both MASTER and Caliper sides used OEMBanjo bolt and Copper Washer, and only Hose used purchased products.
The problem is Front.
MASTER, I assembled it after the Caliper overhaul.
When Air stopped coming out, there was no pressure on Lever, and Piston did not come out at all.
The conclusion is that this mesh hose is behaving badly and
I have been disassembling and reassembling MASTERs and Calipers over and over again.
I've tried all kinds of things, like switching to Copper Washer and then to an OEM banjo bolt.
When I switched back to OEMHose, it was easily cured.
It did not heal after many attempts, so I gave up halfway through and after a month or two, it was completely healed.
Since I installed from Rear first, I didn't think that Hose itself was not good enough.
I really want this time back.
Well, I can't say that strongly because I am partly to blame for not realizing that the Hose itself was flawed....
Quality and texture (Looks.) I give it 3 stars because it is good in itself.
For Controlability, we evaluated Rear's Brake's Touch.
It was neither good nor bad. I didn't feel that it was particularly different from the OEM.
In the end, only the Rear mesh brake hose was used in the Front and Rear Set purchased this time.
I paid 12,000 yen for Rear's Hose only.
To be honest, I thought this price was cheap for Front and Rear Set, but I am soooo sad.
I will never buy a mesh hose from here again.
I can't do it because I am using it, but I want Level to return the full amount of Gold.
But this may have happened because I did all the work for this Brake hose replacement.
I think it is best to leave these matters to Motorcycle shops now.
This time, too, it might not have happened if we had asked Motorcycle Shop to help us.
I hope this Review is helpful.
View detail
Fits: HONDA NSR80, HONDA NSR80, HONDA NSR50, HONDA NSR50
Different lengths.
I had a hard time putting it on because it's longer than the OEM brake hose even though it says it's for a specific model. I haven't run brake fluid through it yet, but I'm worried. It looks good, but I wouldn't buy it again. View detail
Fits: YAMAHA Cygnus X, YAMAHA Cygnus X SR
Please describe the corresponding model
There was no problem with the item but I bought what I searched for in SE44J but what I received was DUGOUT Support + for BREMBO Caliper.
Product information - Suitable models include CYGNUS X 07-15 (SE44J / It is only described as 28S series).
Confirmation is required at ACTIVE before purchase.
View detail
I can not translate OEM at all
Although it is an OEM replacement type, when you install a Bracket that fixes Caliper and Hose, Hose breaks considerably.
Since the position and the length of the crimping portion are different from the OEM, OEMBracket can not mount it unless it bends Hose considerably unreasonably.
I am worried about HoseCrack so I can not install OEM's Bracket, but if it says by car type and singing, I can understand this area by vehicle installation check ??
It is better to think that it is the same length as OEM, Hose with the same Banjo angle only.
I will make a Bracket before Fose Guard rubs Hose and becomes severe.
View detail
RG250γ ('83) I bought it for
We purchased an item with RG 250 γ 83-84 for GJ 21 A 111 - 00 ***. Although the installation method is described as wDirect, how to connect with wDirect is about 5-10 cm Length is insufficient. Since it can not be returned goods because it can not be returned, I used it as it is from the Master cylinder to the junction of the OEM, and connected from junction to Caliper with this product.
Thanks Brake hose is tremendously surplus.
View detail
By car model ??? Bolt-on ???
Because the angle of Banjo bolt is different from OEM, installation on MASTERCylinder side is bad Parenthesis - - -
On the Caliper side, unlike the OEM, it is a straight type, but it interferes with the Fender.
It is necessary to process Fender or purchase Banjo bolt separately.
For the time being, I applied pressure to the Fender and attached it by deforming it.
There is no doubt that it is bad for Hose.
I wonder if this is a Bolt-on by car model ???
Although I exchanged and tried running, Brake 's Touch felt improved, but worked with Caliper' s Overhaul at the same time, it was originally better to replace the old car 's OEMRubber hose, better?
View detail
Delivered goods cannot use die length, being short. I cannot think the goods according to vehicle type. He never buys this manufacturer's goods.
Delivered goods cannot use die length, being short.
I cannot think the goods according to vehicle type.
He never buys this manufacturer's goods.
View detail