Reviews
arrangement
Quality and Texture Information Plastic Products It's neat to look at the feeling of use Products to purchase together TANAX: Off-set Holder 30 [SA-23] It's easy to install Cost performance and comparison to other products TANAX M10 Mirror Bolt WeBike packaging is always great, arriving in a week for delivery and packaging Concerns about purchase TANAX: If you purchase Off-set Holder, you can neatly organize the purchase together View detail
Rearward visibility increases, but ….
The Good
Good about quality and texture.
The mirror surface is easy to see due to its reduced glare and large area.
[Not so good].
Too concerned with Design, it looks lumpy and sharp.
Anyway, it is heavy.
The angle adjustment of the Body section is subtle and difficult.
I have now returned to NORMAL because of the heavy handlebar area, but I would recommend it to anyone who wants a wider rearward view.
View detail
Yamaha's Opposite Thread Screw A must-have for cars
I purchased this product when I switched to Napoleon OnMirror because my OEMMirror was rusting.
The Mirror position is slightly higher, but it was successfully installed.
View detail
There's a lot of freedom
I liked the flexibility of the angle etc.
The mirror surface color is also cool. The weight is a little heavy, but I guess it can't be helped to make it firm.
View detail
Mirror was rusty.
The OEM Mirror was rusty and I was worried about it, so I replaced it with this one. View detail
XSR155 installation
Installed on XSR155.
Set Back Spacer and HURRICANEBMConti2 type Handlebar and Tanax NapoleonMirrorStingray are installed.
Mirror protrudes considerably from the handlebar when the photo is fixed.
If you are going to slip through, Offset45 might be a better choice?
Mirror、Adapter (Opposite Thread Screw) Offset, all to Plating.
If Adapter had been Black, Offset would have been Black.
Adapter→Holder→MirrorIt may be a bit tedious if everything is plating.
However, I don't think it would be a bad idea to have everything in Plating.
View detail
Easy to install and looks completely different, so it's good.
The price may be a little high, but the quality is high, so I am very satisfied.
Since it was all black, I bought Green Light for VehicleLine tape to match the color of the car body and applied it.
The 3mm width is a little short, but it is easy to apply and I applied it along the underside, so it doesn't bother me that much.
I was rather thinking that this would be better since Tape was thicker and could not be applied properly if it was 5mm wide.
View detail
I wanted to lower the overall height.
Mirror requires a lot of tools for adjustment. View detail
It is a product that fits very naturally.
Since it hasn't been installed yet, I'll replace it with a photo of a club member. It matches as if it was originally installed by the manufacturer. Both build quality and materials are excellent. I first heard from a club member who installed it that rust does not form even without the bolt cap. It is heavy and feels solid. Very satisfied.
-------------------------------------------------- -------- It is still installed, so it is replaced by a member of the club members. It suits the manufacturer as if it was originally mounted. Both builds and materials are great. First of all, I listened to the members of the club. The weight is too heavy, so I feel hard. Very satisfactory. Powered by Google Translator
View detail
Fits: KAWASAKI Ninja1000SX, KAWASAKI Ninja1000SX, KAWASAKI Ninja1000, KAWASAKI Ninja1000, KAWASAKI Ninja650, KAWASAKI Ninja650, KAWASAKI Ninja650, KAWASAKI ER-6f, KAWASAKI ER-6f, KAWASAKI ZX-6R, KAWASAKI ER-6f, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-25R, KAWASAKI Ninja250SL, KAWASAKI Ninja250, KAWASAKI Ninja250, SUZUKI GSX-R1000, SUZUKI GSX-R1000
Installation is not quite right
I didn't like the OEM's tactile Mirror so I replaced it. As a result, I am satisfied with the new Mirror because it is easier to see the back of the car and looks better than the OEM Mirror. The installation was not so easy to understand. View detail
Easy to use
I ordered this Mirror because it was difficult to see the OEM Mirror, and after looking around on Youtube and other reviews, I found that this Mirror had a good reputation. As a result, I found that the Mirror has a wide range of installation options, including the ability to be offset to the back of the room, not to mention the ability to operate normally. View detail
OEM Parts Flavor
[How is it used?
In conjunction with the conversion of the Mirror on the 390DUKE to an Other Brand Product, we decided to use the Tanax Off-set Holder 45 (product number:SA-25) to improve the Mirror's visibility, I installed this product to prevent water from collecting in the hexagonal holes of the bolt and rusting.
Was the one you received as per Image?
Material:It is a Plastic Cap. If you handle it roughly, it looks like it will be damaged soon.
Was the installation difficult?
There are no claws attached to prevent it from falling off, but it is a little tight-fitting so that it will not come off immediately. I tried to remove it once as a test, but it was quite difficult, so I don't think it will come off without permission while driving.
How was your experience with it?
I am satisfied with the finish as if it were OEM Parts.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Point or hang for installation:If the cap is pushed in at an angle, it will break. if the inside of the hexagonal hole is already rusted, it is better to remove the rust first before installation.
Instruction Manual:There is no Instruction Manual, but as you can see, it is a simple structure, so you just need to push it gently into the hexagonal hole of Bolt.
View detail
Style is very good, but...
I fell in love with Style and bought it!
The handlebar area looks very sharp and good, but the narrower width of the upper and lower sections makes it harder to see than the OEM.
In my BOULEVARD, the vibration causes the rear vehicle to shake when the speed exceeds 70 km/h.
Blue lens is quite good.
View detail
It was not sold at Home center.
[How is it used?
KTM Motorcycle's Right SideMirror is Opposite Thread ScrewSpec. just like Yamaha's. I decided to use the Tanax Off-set Holder 45 (product number:SA-25) to install the Mirror on my 390DUKE as an Other Brand Product, so I needed an M10 Reverse Screw bolt to install it.
Was the one you received as per Image?
It is very helpful that M10 reverse screw bolt is not sold at ordinary home centers.
Was the installation difficult?
To prevent the bolt from loosening, Screw lock fluid was used to install the bolt. Also, to prevent water from accumulating in the bolt's hexagonal hole and rusting, a TANA-X M10 Mirror Bolt Cap (product number:BCM-10) was installed as a waterproof measure.
How was your experience with it?
I installed Off-set Holder 45 with this Bolt, which improved Mirror visibility.
[Included Parts:were they on?
One Nylon washer is included but was not used this time.
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Items to buy together:Screw lock fluid, M10 Mirror Bolt Cap
View detail
Fits: YAMAHA XSR900, YAMAHA XSR700, YAMAHA MT-10SP, YAMAHA MT-10, YAMAHA MT-09SR, YAMAHA MT-09, YAMAHA MT-07, SUZUKI ST250E, SUZUKI KATANA, SUZUKI GSX-S750, SUZUKI GSX-S1000, SUZUKI GSR250, KAWASAKI Z900RS, KAWASAKI Z900, KAWASAKI Z800, KAWASAKI Z650, KAWASAKI Z250SL, KAWASAKI Z250, KAWASAKI Z125PRO, HUSQVARNA Vittopilen 701
Yes.
The OEM was replaced with something like ”arinko”.
This is the only bar end mirror that has a range of motion inside and outside 。 One choice!
Mounted face down. 。 Therefore, it is a little difficult to see.
Although the position is somewhat less visible than the OEM, there is no substitute for the feeling of openness with nothing in front of you.
Ball joints will not move when coated with liquid rubber.
The screws of the restrainer will not loosen due to vibration if they are handled with Screw Lock.
The supplied in-bar mounting parts are not used. The original OEMRubber parts are the most well-fixed.
The car passed inspection without any problems.
View detail
Texture
The quality is excellent. As other reviewers have said, the weight of the Single Item ensures visibility and does not shake due to vibration. Of course, the Mirror section is smaller than the OEM section, so visibility is lower. However, this is not a problem for me, as I can adjust the size of the Mirror section to my preference. View detail
textured good feeling
I am satisfied with the texture and design. The adjustment can be set in detail. It would be even better if the Mirror section could be moved up and down, even if only a little. View detail
The product is as expected.
I am satisfied with the quality and design, and I think it is worth the price, especially with features such as the Turner. [Color] If you can Clear, I have no complaints. View detail
Blue Mirror is cool.
I really like the Blue Mirror.
The Mirror does not blur while driving and is comfortable.
I think Tanax is a reliable Brand.
They answered my inquiries in a friendly and courteous manner.
View detail
Blue color is eye-catching
This is a replacement for REBEL250 from OEM Product.
I tried to remove and attach OEMMirror, but it would not fit.
Manufacturer was instructed to remove the Mirror mounting base (silver color) attached to the telephone handlebar on the spot. It was safely attached.
The gap between the Brake fluidCase and the RightSide Mirror Base is a little small, making it difficult to turn the 17mm Spanner when installing the RightSide Mirror Base.
I am also satisfied with no blurring or loosening while driving. No loosening etc. I am satisfied.
It turned out very cool.
View detail