Reviews
For additional Helmet mounting location
Purchased Helmet to attach it to places other than Mirror.
Installation is very easy.
Simply remove the Bolt from the Number and attach the PlateHolder together with the Bolt.
There is no need to add any other Bolt or Screw.
Anyone can install it in 5 minutes.
This time, I installed it on YOSHIMURA's Fender Eliminator Kit instead of OEM Fender,
No glitches or problems at all.
Also, I installed it with the supplied bolt, but other License Plate Bolt should be no problem.
I think
The construction was quite solid, thicker than I expected and Firmly.
The surface finish is also Beauty.
Helmet holder is Quantity:Pair (for Left and Right) Either can be attached.
Easy to remove and install.
The key part is a bit weak due to pushing, but that's about it.
It's not so much to prevent theft as it is to keep the Helmet on when you leave the Motorcycle for a while.
I personally don't care about it because it is the thing of the
I also installed a Holder on the SIDE of the car, but when the Exhaust System hits the car and it is immediately after running, the Holder is not installed.
It was a little difficult to use, so it is nice to be able to put it on without hitting the Exhaust System.
However, it does hit the Tire a bit, so those who are concerned about sogginess may need to take some measures.
Also, if you are in a windy place, the Exhaust System will sway quite a bit and hit the Exhaust System, so be careful there as well.
The supplies do not stand out as a Custom in appearance.
But the installation is easy and useful.
On the other hand, because it is inconspicuous in appearance, it is not so conspicuous in Styling and Silhouette.
It's good for people who don't want to change.
If the price were a little lower, the cosmetics would be perfect.
View detail
I'd rather not use it if at all possible...
There is nothing wrong with not using it!
Many people say that racing sliders are conversely dangerous on public roads because they slide when they fall over.
View detail
Surprisingly good.
I thought it would be halfway to Colorful if I changed only the lid, but I changed it to try it out. View detail
Fallen cannibals
This part protects the engine in case of a fall, and I think it looks good as a parenthesis. View detail
Fallen cannibals
The price is double that of the same racing slider, but we chose this product because there is no need to drill holes in the curl, and because some people have had their frames bent when they fall over when directly attached to a frame, although this is a different type of car.
The product is easy to install, but it takes some skill to remove and install the curl.
View detail
The installation was a little Large weird!
I bought it because I like the way it looks.
I first replaced only the top bridge cover, but I wanted to replace the handlebar as well, so I later added the handlebar as well.
I'm very satisfied with the product!
The Bolt has a Screw Lock, so it's a little weird to remove the OEM first time.
Changing the Position makes it easier! but a slight change in position does not make it easier! (Lol) The brake hose interferes with the Meter area, although it was stated that it is OK to install.
View detail
Funnel Type, so Parenthesis is good!
I think the price is high for what it is, but I like the look of the Funnel Type!
It is easy to install., to One point!
Happy with the results!
View detail
It depends on how you view the fact that the Position does not change to Large width.
I couldn't find any photos of the Black Anodized Aluminum version on the ManufacturerHP, etc., so I'll expose them for your reference.
[Functional aspects.
At the grip end position, the bar is lowered by about 1 pc.
The hanging angle will make hang-off a little easier, but will it be worth the price?
To put it bluntly, I would like to lower the angle of attack and squeeze it even more.
Other than the angle, the NORMAL sturdy-looking Casting IronHandlebar is unusually heavy, so
There is a Merit that can be significantly lightened by changing to an Aluminum Handlebar.
Finish, color
The finish of the thing itself is good.
I chose Black Anodized Aluminum because I don't like the customized look.
If you don't know it, you may think it is STD Handlebar. It looks cool.
Anodized will fade more or less over time, so I think it will eventually color Gap.
Installation
I know many people are concerned about this, but it requires drilling. However, since it is aluminum, it is surprisingly easy.
Replacing the Universal iron bar handle is much more troublesome. The procedure is as follows
1) Remove the clutch side grips and clean the remaining bond with a scraper or parked grips.
2) Loosen the screws on the Left Switch Box and ClutchHolder.
3) Remove the Handlebar from the Top Bridge and pull out the ClutchHolder and Switch Box.
4) New handlebar is temporarily attached, and the switch box is positioned.
5) Measure the distance of the hole from the end side of the old Handlebar, drill a 5φ hole at the same distance, and install the Handlebar.
6) The Brake Side is basically the same work, but the Brake Side is easier because you don't have to remove the grip rubber.
Switch box is not something you touch all the time while driving, so you don't have to be nervous about the hole drilling position.
One thing to note about the work is that Gixxer has a strange structure with a non-split ClutchHolder, so the glue is glued to the Grip.
If there is any left, it will get stuck and be very hard to pull out. 1) I recommend cleaning it with Beauty instead of lying on the floor (self-discipline).
View detail
Fits: SUZUKI GSX-R1000R, SUZUKI GSX-R1000, SUZUKI GSX-R125
If you can afford it, buy it.
I bought it because I missed the part where I removed Mirror from the Circuit run.
It should take less than 10 minutes to remove the Mirror and install it.
Anyone with tools can do it.
Bolt is included, but Nut uses the original.
It is a little expensive. If you are dexterous, you may be able to make it yourself.
View detail
Appearance will change.
I couldn't do it myself, so I used PitService for the installation.
OEM Casting Sense." I don't like to use the handlebar, but I don't want to drive aggressively, so I replaced only the handlebar. Rear Sets are already installed and the position can be ridden without any problem.
(Not in the product description, but drilling is required.
It was difficult to find the replacement image of only Handlebar with their own Initial Adjuster and Bar End on the Manufacturer's website.
View detail
Funnel Type and looks good!
I had a different Manufacturer, but I decided to go with AGRAS this time.
Funnel Type is my personal favorite!
I didn't find a color I liked, so I'll have to paint it, but it's aluminum and has a nice texture! Looks good!
View detail
Satisfies
About quality and texture: I wanted one with a logo, but I am satisfied except for the one without a logo.
About the feeling of use: It looks solid and is reliable. I'm talking about the price.
Products to buy together: The front slide was fitted with Yoshimura, and this slider was used to protect the rear muffler.
Difficulty of installation : There is no difficult part ------------------------------------------ ---------------- About Quality and Texture: I wanted to have a logo, but I am satisfied except that there is no logo About the Feeling of Use: It looks solid and reliable. Products to Buy Together: The front slide is equipped with Yoshimura and used this slider to protect the rear muffler. Difficulty of Installation: There is no difficult part Powered by Google Translator
View detail
Requires T30 Torque for installation
The texture is quintessential AGRAS, it's Beauty and especially effective when standing up (I just hope I don't have to take care of this Slider). The only thing to do is to remove the OEM TorqueT30 and put on the supplied Bolt. But it's still expensive… View detail
Fallen cannibals
There are various sliders available from various companies to protect the Pulsar Cover side of NINJA, but I decided to purchase AGRAS's slider because it looks Parenthesis and it was reasonably priced.
I will drive safely so as not to be indebted to this.
View detail
AGRASSlider
It is good for installation without Cowling's modification. View detail
The things are good, but I wonder if they are too expensive.
I bought it because of the way it looks, but I wonder if the price is too high. I think so.
It was easy to install with just a simple push-on. Looks good!
View detail
It looks great?
We purchased it because we also wanted Accent for the front wheel of our Motorcycle.
To be honest, I put it on just for looks, but I am satisfied with the Large size, and I have added a cap to the gold POSH bolt for the M6 bolt for installation.
It is also a recommendation for those who want to add an "Accent" to their Motorcycle.
View detail
Slider
The product is quite good, the Rear is better than the Front to fit the Large size car body. View detail
Design Fine
The design is good, but the price is high. I wish the price could be a little lower. View detail
Parenthesis OK
Parenthesis is nice because it is a little short and not very noticeable. I like the fact that it has the AGRAS with Logo. It would be better if it were a little cheaper. View detail