Reviews
Fits: HONDA 400X, HONDA CB500F, HONDA CB500X, HONDA CB650R, HONDA CBR400R, HONDA CBR500R, HONDA CBR650R
Good matte feel.
I was looking for a good one to prevent scratches on the meter. I bought this one when I used to ride a CB250R and it was good, so I bought it again because I changed the model of my car. It comes in two types, glare and matte, but I personally prefer matte. (without Gloss) is my preference because it is easy to see with less reflection etc. It is relatively easy to apply because it comes with a tool, but I think there is a hang. It is the same as the protective film for cell phones. View detail
Fits: Others
Large durable even in the rain!
It was attached to an OEMCigar socket on a ninja650!
It's convenient because the insert glows Blue.
View detail
Fits: KAWASAKI H2 SX SE, KAWASAKI H2 SX, SUZUKI GSX-S1000GT, SUZUKI GSX-S1000GX
It's not cost effective
It is an old type that is difficult to put up for the price, and you have to pour water on it to remove the air. It is hard to see in the picture, but a lot of air remained. View detail
No discrepancy in design.
Easy to install, no design discrepancies
I use the double-sided tape provided. (Shown on the Right in the fourth photo) indicates disappointment for not having done what one wanted or intended to do
We used 3M's Ultra Strong Double-Sided Tape
The rest is drilled with a 4mm Drill and the material provided.:Fixed with PlasticPin and done.
Firmly attached and will not come off.
It is hard to tell the effect when it rains hard. (You will get soaked anyway.)
After a rain or when running in mountainous areas where water is flowing, there seems to be less splashing.
Well, if the price were a little lower, I'd give it 5 stars, but I'll give it -1 star for that.
View detail
Fits: HONDA CB1100RS, HONDA CB1100EX
It's hard to say...
The size is also a little small. The CB1100 meter is difficult to position because the part to apply the meter is deep....
View detail
Fits: HONDA SUPER CUB C125
Spherical Panel support?
The first one was a failure, it was full of wrinkles and I threw it away immediately. the second one I pressed down slowly and radially from the Center positioning, but the air bubbles remained hard to see. It was more difficult than with a smartphone. I thought about peeling it off, but it was a waste, so I left it as it was. Would it be better to stick it with soapy water? View detail
Fits: BMW RnineT, BMW RnineT, BMW RnineT /5, BMW RnineT Pure, BMW RnineT Scrambler, BMW RnineT Urban G/S
Satisfied
Purchased to prevent dirt inside Fender
I think it works personally.
View detail
Fits: ROYAL ENFIELD Himalayan, ROYAL ENFIELD Scram 411
This is a dangerous PARTS and you should definitely not do it.
This is a fairly appropriate spec. that uses a single tie band to secure it to the swing arm. To detach the Swing Arm, it is necessary to remove the Rear Tire, insert the Swing Arm between the Rear Tire and the Swing Arm, and tighten it with a single Tie Band.
I was concerned immediately after installation, but after touring I realized that it was even more dangerous.
(1) First of all, the Fender tilts about one centimeter toward the Tire side due to driving wind pressure. (2) The clearance between the Fender and the Tire becomes narrower, and in the worst case, the Fender is rolled into the Tire, resulting in a large risk of breakage.
No matter how tight you tighten it, it is only a tie band. It cannot be fixed tightly.
I was not convinced that it was worth the price.
Once I installed it and damaged it, I couldn't return it and lost a huge amount of money.
I would never recommend this product.
View detail
Fits: KAWASAKI H2 SX SE, KAWASAKI H2 SX, SUZUKI GSX-S1000GT, SUZUKI GSX-S1000GX
I could put it on Beauty!
Purchased to prevent Wound on Meter panel
Meter panel and film with water mixed with a small amount of neutral detergent.
Spray both and affix.
Air bleed with the included Card and you are done!
I'm happy with how it looks on Beauty.
View detail
In Mudguard.
Radiator guard is now less dirty.
Installation at a store is recommended.
View detail
Fit but not cosmetic.
It is for Tiger sport 660, so the size feeling is Exactly.
I don't use the plasticrivet that comes with the product because I am somewhat concerned about the protrusion of the plasticrivet on the inside.
I have only used the supplied double-sided tape for fastening, but if the tape is degreased and treated with a fire retardant before bonding, I think there will be no problem in my experience.
However, it is not guaranteed when a strong force is applied to it by any chance.
I have not yet run in the rain or on unpaved roads, so I have not tested it yet, but I bought it because I thought it might be useful for Triumph's recent bodies, which seem to have a lot of mud splatter due to their short mud guards.
However, it is too expensive for what it is, which is a drawback.
View detail
Fit but not cosmetic.
Same imprementation as for Front.
It is for Tiger sport 660, so the size feeling is Exactly.
I don't use the plasticrivet that comes with the product because I am somewhat concerned about the protrusion of the plasticrivet on the inside.
I have only used the supplied double-sided tape for fastening, but if the tape is degreased and treated with a fire retardant before bonding, I think there will be no problem in my experience.
However, it is not guaranteed when a strong force is applied to it by any chance.
I have not yet run in the rain or on unpaved roads, so I have not tested it yet, but I bought it because I thought it might be useful for Triumph's recent bodies, which seem to have a lot of mud splatter due to their short mud guards.
However, it is too expensive for what it is, which is a drawback.
View detail
This is a must have for Rebel 1100
I installed it on the Red one's body and it does not feel uncomfortable.
The REBEL 1100 is miserable around the Radiator when running in the rain or on watery areas.
I wanted to have a Long fender instead of Short as an OEMOption, but this product replaced it.
I was satisfied because it was easier to clean after driving and it didn't look bad.
Installation is also easy with double-sided tape.
As a precaution, it would be better to treat the joints inside the Fender with GORILLATape, etc. to prevent them from falling out.
View detail
Fits: SUZUKI V-Strom 1050, SUZUKI V-Strom 1050 XT, SUZUKI V-Strom1000
Reduced mud splashing on Engine.
I think the mud splatter from the direct hit to the Engine is gone, and I am satisfied with its function as a Mudguard. The texture of the product is not so good. I thought about painting it, but I had some Carbon Seat left over, so I put it on. The double-sided tape is just to reduce rattling and has no adhesive power. View detail
Hoping to prevent stains on the car body.
In the case of NT1100, mud splashes will contaminate the rear suspension and spring,
I resorted to this one.
I think there is a LARGE difference with and without.
P&A products seem to have good Coverability.
One of the mounting holes was slightly out of alignment.
Cracked.
There may be individual differences, but if it doesn't fit slightly when you install it, don't push too hard.
It is better to process the hole Small.
View detail
Fits: SUZUKI Hayabusa
Meter panel
The product requires the same level of skill as a PRO to affix, and even a slight breeze when working outdoors can cause dust to stick to the adhesive and create air bubbles. View detail
Fits: HONDA SUPER CUB C125
It's easy to paste. (^^)
Other postings say that it is hard to stick, but if you fill a spray can with water and add 2 or 3 drops of dishwashing detergent, spray the Meter and stick this film on it, handle it with the included cardboard for leveling, and let the water out, you can stick it on the Meter EXACTLY. Even if the blisters remain, they will be on the Meter after 2 or 3 days. View detail
As Radiator cover
I purchased this product to avoid dirt and foreign objects in Radiator!
The installation was done at the store.
He did it for several thousand yen.
It was quite a good purchase!
View detail
Extender Fender
The Radiator was dirty with mud and small pebbles etc. in the Radiator as OEM, but by installing this product on the FFender, the dirt was almost eliminated. I am satisfied with the installation of this product on my Rebel 1100T. View detail
Extended length of Rear Fender
It is difficult to see the effect compared to the Front side.
The price is higher than Front.
I feel like it could have been done without.
As with the front, double-sided tape is not used, but only the clip is used for mounting.
View detail