Reviews
sharp (blade)
Unlike cheap Scraper, it is sharp.
Gasket removal is Exactly for Gasket removal is very efficient because it can be removed pleasantly.
View detail
Essential tool for tightening Torque management
[How is it used?
Torque control for tightening the Rear Axle Nut when adjusting the chain, etc., and for relatively large torques.
Was the one you received as per Image?
It was just as Image.
I had another KTC Torque wrench with a lower Torque value, so I made it a Large wrench as it is.
How was your experience with it?
Easy to use
The scale is also easy to readQuantity:It is easy to Set.
It is also easy to understand the Click feeling when the setting Torque is reached.
[Points to note]
Naturally, a larger Torque setting requires more force for tightening.
That said, if tightening is done with too much force all at once, it will result in overtorque, so care should be taken.
How did it compare to other products?
I have not compared it with other products.
Other items that would be helpful
12.Purchasing an Adapter from 7sq to 9.5sq is also a convenient way to increase the number of available Sockets.
View detail
Easy to use
This tool is ideal for gripping Snap rings.
The Grip is also easy to hold and non-slip, making it easy to work with.
It is easy to use and indispensable for maintenance.
View detail
Required for Deer Bell Oil replacement.
It is essential to remove the DucatiOEMOil Filter from Deer Bell. I bought another manufacturer's filter of the same large size, but the shape of the corners did not fit and it became waste. View detail
Ratchet is easy to use
It is easy to use because it does not need to be replaced when working in a confined space.
The quality is very good and the Ratchet works efficiently.
It is sturdy and will not break even if a certain amount of Torque is applied.
View detail
excellence
This is indeed KTC's exclusive tool.
It is safe to loosen the lock nut of the tie rod.
It is useful because it is easy to apply force and can be worked safely without slipping.
View detail
It's solid
I use it to transfer tools when I carry them around.
It is convenient because it is easy to hold and has a solid capacity to fit what you need.
The solid construction makes it safe to put heavy tools in it.
View detail
It is quite easy to use.
It is a little expensive, but quite easy to use.
The bite is different from Home center's cheap products.
I have been using it for about 2 years and even the Screws that seem to lick it don't lick it.
View detail
Hard texture.
As mentioned in the Title, it has a hard feel.
It is difficult to use on subtly curved objects such as Cowl, though.
Like Cylinder gasket, good for flat surfaces.
View detail
easy to hold
It is indeed KTC.
Compared to a regular Hexagonal Wrench, it is easier to grip and apply force, so it is possible to apply Torque firmly and turn the Bolt reliably.
Long and easy to reach Bolt in tight places to increase serviceability.
View detail
Handlebar feels good with 90-degrees rotation
I bought it because it can be tightened and seems to be able to be turned quickly at the clamping place.
It has replaced the ordinary Ratchet wrench and is now one of the Main tools.
About 55 Nm (Axle Shaft) is the upper Torque value I have used, but
We have been able to use the system without any problems.
I guess the fact that the handlebar turns more than 180 degrees is the selling point.
The handlebar swings in both directions even when it is straightened for fast turning, so it is difficult to turn the handlebar during fast turning.
The ratchet part can be maintained (parts are available), so it can be used for a long time.
It is good for those who are looking for a Ratchet wrench in the future.
View detail
Can use
It's a small turnaround, and it's
All required Sizes are in Quantity:It is convenient because it is a Set.
We can work in places that Socket's Bit can't get into.
It is more convenient to have it.
Since it is made by KTC, it is well made.
It was also accurate and did not tarnish.
Good tool.
View detail
Convenient to have
I bought it because it picks up Bolt, etc. dropped in the crevices.
It has sufficient magnetic force and is Flexible and bendable to pick up objects even in tight spaces.
The texture is also solid as it is made by KTC.
It doesn't feel like it will break while in use.
If you do your own maintenance, especially around the Engine
I think it is essential to have it.
However, the price is high.
The evaluation may differ depending on what you think of this price.
View detail
Surprisingly difficult
I bought it because I thought it would be convenient.
Since it is a KTC, the texture is solid and not easily broken.
The grip is also processed to prevent slipping.
It does not slip when turned with greasy hands and is functionally up to par.
Just my opinion after using it.
I'm not sure if it would be dramatically more convenient, but it's quite a hassle to put it on and take it off.
Always use a quantity on the Ratchet Handlebar rather than a Single Body.:Set and then use the
I feel that it will be used by turning it around when it is loose.
I don't suddenly loosen the bolt on the Ratchet Handlebar, and the Ratchet Head is too big to fit in tight places.
The situations in which they are used are currently limited.
Usage may need to be considered.
View detail
It is cheap and good
It was cheap, so I bought it to try it out.
(Cheaper than KNIPEX)
It was surprisingly easy to grip and use.
The teeth Edge is nice and sharp, with few rattles.
It can grab things firmly.
The soft grip also has subtle unevenness, so it does not slip when held by an oil hand.
I think the cost performance is outstanding.
If you are not concerned about foreign brands, I can recommend this Pliers.
View detail
A parallel two-cylinder 2Cycle can reach it!
I purchased this product to use for R1-Z.
So far, I have not had to replace the plugs on the road, but I have a set of plugs and this Wrench tucked under the Seat.
Please note that if you have a parallel TWIN 2Cycle, it has a shape that can be used donpically, but if you have a 4Cycle or other Plug in a secluded location, it is almost impossible to use it.
In this case, we recommend a SocketType Plug wrench with Rubber inside to keep it from falling off.
This Wrench has a notch that allows the Plug Cable to be inserted even in tight spaces.
It is convenient to have one because it is not hexagonal and can be tightened little by little.
View detail
Good accuracy
These tools may not be accurate, or they may not come off in anticipation, or they may not be able to come off.
Licking can cause scratches.
This product is so precise, it fits perfectly.
Loosening and tightening can be done very Smoothly.
It is a reliable Brand and will be used for a long time.
View detail
Easy to use
I bought it to do an Oil exchange.
It is useful as a parts tray for cleaning and disassembling parts, and for a variety of other uses.
It's well made, so it doesn't dent easily.
It will last a long time.
I think the Large capacity ones are easier to use.
Large doubles as Small.
View detail
Lightweight and easy to use
[How is it used?
Purchased because I could not find OEM supplied tools.
There is a Rubber inside, and when the tool is pulled out of the Plug hole, the Plug can be pulled out together.
The same is true when installing the plug, which allows the plug to be dropped deep into the hole to minimize the risk of damaging the electrode.
Was the one you received as per Image?
Yes
How was your experience with it?
Easy to use
[Points to note]
None
How did it compare to other products?
Lighter than OEM
▼ Other items that would be helpful include
Is the unit production cost 10 yen?
View detail
Easy to use
[How is it used?
The size of the Fixing Screw of the Generator Cover is Large, so I purchased the No.3 number because the normal Phillips Screwdriver was almost tarnished.
Was the one you received as per Image?
As shown in the picture, it was bigger than I expected, but it was just right for my use.
How was your experience with it?
As described as a firm Fit to Mt. Screw, it was Firmly engaged and did not feel like it was going to lick at all.
I thought it was comfortable to hold and very easy to turn.
The hexagonal shaft makes it easy to apply Torque, and it is also used as a penetrating driver, so it is likely to be used more often in the future for maintenance of old cars.
[Points to note]
It is difficult to get a sense of size, but for the 1st pc Penetrating Driver, No.1 or No.2 is good.
I chose No.3 because the Screw mountain I use is a bit deep and wide.
How did it compare to other products?
I only had a Phillips Screwdriver, which I didn't know well at Homsen, but it is incomparably better than that.
The ease of use, such as the feeling of fitting snugly to Screw Mountain and the ease of gripping, is good for the price.
【Review】
It was easy to use, as it is a highly rated Driver.
For light maintenance, an inexpensive one would be fine, but for those who do heavy maintenance, it would be worthwhile to have one pc.
View detail