Reviews
![Fitting for Monorack [5137FZ]](https://img.webike-cdn.net/catalogue/images/91664/21033_01_TS.jpg)
RearCarrierQuantity:Pair (for Left and Right) The bracket does not align with the base mounting holes on the top case.
I purchased this product to install GIVI's Mono-lock case 47 on my F900XR. I would like to comment on the installation process and the state of use.
(1) RearCarrier's Bracket is LeftOnly Right and Quantity:Pair (for Left and Right) Since there is no Bracket to link the Quantity:Pair (for Left and Right) There is some difficulty in determining the horizontal state of the Bracket.
The ?Instruction Manual is somewhat confusing.Quantity:Pair (for Left and Right) It would be good if the distinction between Bracket and the reverse side is clearly indicated.
(3) Base plate hole and quantity on the bottom of Top case:Pair (for Left and Right) Bracket holes are FrontQuantity:Pair (for Left and Right) Two of them fit, but not the Rear. However, the Rear hole was not inserted, and since the Bolt hole was shifted from the normal position, I am not sure about its strength.
Also, the position cannot be adjusted back and forth.
?There are no strength or other problems so far in using Top case, but the position of Top case is quite high.
I would like to see the Bracket extending to the rear of the vehicle reshaped so that it is lower. Also, the Top case is slightly further rearward than the rear wheels.
View detail
![[Repair Parts] Screw Set](https://img.webike-cdn.net/catalogue/12366/65884_1_l_TS.jpg)
For fixing Base plate
I bought this to put a base plate on another Motorcycle.
It was very helpful that you sell them as Repair Parts, since they contain special Washers, etc.
View detail
![Rear Box [E30RN]](https://img.webike-cdn.net/catalogue/images/75563/16976_TS.jpg)
I think the structure that allows the key to lock even when it is not completely closed is defective.
I have used several types of LargeSmall cases for GIVI products, but this is the first time for me to use the MonoLock type.
The old locking mechanism of early products, where the lock would get caught on something and prevent the door from opening, has been eliminated, but the fact that the door is locked even when it is not locked is a large drawback. Of course, the root cause is that the user does not check the well, but when I was in a hurry, I ran thinking that I had closed the door and was in a hurry to see if I had lost something after arriving at the destination.
It would be nice if the structure of the key could not be turned if it is not locked as in other companies' products, but I wonder Large why such a structure was chosen.
View detail
Good as a stop lamp, although contact failure occurred at the open/close contact point.
Purchased as a retrofit for GIVIMonokeyV47.
(Please keep that in mind as you read this, as it may just be a problem with the one I purchased.)
The evaluation was lowered due to incomplete contact of the contacts in the BOX open/close section, which did not function or not function.
As a result, this open/close contact is discarded and the original Stop lamp function is usable by direct connection with a cord.
Is there a need to put a contact Switch on the opening and closing part of the Box in the first place? I would like to ask the development team.
I hope you understand how long it took me to figure out the phenomenon of the Stop lamp not coming on even though the power is on and solve the problem by directly connecting it by my own work.
As for installation, I think it is better to ask PRO to do it because it requires some skill.
Failures may occur that cannot be handled by amateurs.
Detailed impressions below
0 Installation
LED Lamp Installation:Easy
Wiring:The inside of V47 is uneven, making it troublesome to put together (wiring fixture must be purchased separately).
Open/close contacts:As mentioned above, we believe that when the BOX open/close part is completely closed, the contact is just a little bit bad and the power will not be energized.
Carrier side contact point:It is a hard work to make a hole on the box side and the carrier base side, but it is no problem if BALI is handled.
Wire connection with MotorcycleBody:I purchased a coupler separately and connected it.
0Stop lamp function
Safety is our top priority, and since Chest is willing to invest in safety even if it costs gold, we really wanted a stop lamp for the box.
If it's this expensive, I'd like to add a Blinker function.
We have a GIVIUniversalBaseplate installed on a HondaFORZA250 OEM carrier, and the box is close to the stop lamp, so it is difficult to check the stop lamp from a higher vehicle such as a truck.
0Others
Since the Gold amount is high, it is still better to eliminate the open/close contacts and reduce in cost by using direct wiring.
The open/close contact point may be good for parenthesis, but it eats up space inside the box, and depending on the cargo inside, there is a risk of damaging the box by applying force when opening and closing it.
I can recommend it to my friend if I am supposed to accompany my friend to install it.
I really want a Box retrofit for the Stop lamp, but I don't have the sukill experience to make it completely myself, so overall I am glad I bought this product, which is sold as a GIVIOEMKit.
View detail
![MONOLOCK Base [M5M] for FZ Series](https://img.webike-cdn.net/catalogue/11160/60145_1_TS.jpg)
Fits: HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CB1000R, HONDA CBF1000 06, HONDA CBF1000 07, HONDA CBF1000 08, HONDA CBF1000 09, HONDA CBF1000 10, HONDA CBF1000 11, HONDA CBF1000 12, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500, HONDA CBF500
Exclusive goods
I feel that it does not have to be a dedicated product. View detail
![Optional Lamp Kit (LED Type) [E126]](https://img.webike-cdn.net/catalogue/12366/21178835_all_1_2_TS.jpg)
Wiring is too small.
The wiring to be installed in the box made by Manufacturer was broken during the second opening and closing.
The wire was torn out from where it was fastened with Nut.
I reconnected it myself.
Also, the contact with the Body is poor, so it flashes with vibration
I can't use this.
The build quality is lousy for the price.
I'd like to improve on that.
I have no choice but to connect it directly and use it somehow.
I'm not sure if I would recommend it to others.
View detail
We can't expect much.
It looks larger than OEM, but I put this product because the one I installed before was too large and was agitated by the wind. I use the metropolitan highway well, but if I do not lie down, the aerodynamic Advantage is the impression that is not different from OEM. On the other hand, on the day of the tailwind, I feel that I receive the wind more than OEM, and I feel some influence on Handling. View detail
![[Repair Parts] MONOKEY Base Single [Z230]](https://global.webike-cdn.net/photo/impression/90/90ea3232648f95d06c7d6064d10c5c63L.jpg)
Processing is a prerequisite product. There is no accessory parts, so it is necessary to purchase separately.
Top case of GIVI "Monkeysystem" Purchase to use multiple bikes. Product is only plastic base, it is necessary to separately purchase clamp attachment, mounting bolt etc. Since accessories etc. are not contained at all, attention is necessary. Since the only thing that fixes the product and the motorcycle is only two bolts, a rugged carrier is necessary for installation. Moreover, processing such as opening a bolt hole for attachment is necessary also for that carrier. I built and installed auxiliary carriers with bolt holes opened by welding. Processing is a prerequisite product (The one of the monolock system can be fixed with four bolts, so it seems that it can be installed without processing). Once installed, there is no rattling between the box and the base and it can be fixed firmly. In addition, a guide line for attaching an optional stop lamp is also molded on the back side of the base. However, although it is a plastic one, this price is too expensive. View detail
![Metal Rack [E96B]](https://global.webike-cdn.net/photo/impression/69/69324e4c3f5b553c42dbb2405bd4a446L.jpg)
GIVI box Custom
It is Carrier which pierces and installs GIVI box.
Drill is required for installation, and Sea Ring is required as Waterproof, so it takes time and effort.
After installing it seems that the Custom feeling has come out quite a lot, but I like it, but actually, since Hook does not hang, it is worth paying a high Gold.
View detail
![Mono Lock Case [E30TN2]](https://img.webike-cdn.net/catalogue/images/15075/94145_O01_TS.jpg)
Cheesy
The price is expensive and not very good qualitatively!
Because it looks cheap, it is better to buy Box at Home center and install it by your own work! I think that it is making it sold in the end after all!
It was in the box, but the Box was too dirty and it was the worst!
View detail
I tried installing it - - - I immediately removed it.
I liked Design and Large Kimono, I was pleased that I could buy cheaply Large, but I could not firmly fix the installation of UniversalBase and Body firmly.
Also, with installation of Case and Base, I do not know what state the semi-lock state is.
Falling of Body becomes an uneasy material at high speed driving
As I understand later, it is necessary for our car body to have its own Base. This will be close to 30,000 yen.
In that case, the person who attached the top case of the OEM abandoned the installation thinking whether it was easy to look and was safe even at high speed driving.
If you have a car body fitted with Flat Carrier I think you can secure it firmly even on UniversalBase.
For low-speed mopeds orScooter? I want to display the corresponding speed.
View detail
I am thankful that there are many Repair Parts
Mounting Bracket of Box I bought in second hand was rusted, so I replaced it for this item. Both come rusty but new items are pleasant.
However, it is difficult to install - - -
In order not to bend Base, Spacer is compulsory, so that those who are installing without using this product can also see.
It is better to overlay the 6 mm thick Washer into a Spacer or to add scratches and rubbing to gold items with Gap prevention.
View detail
The Clip attachment portion is omitted, Large strange shame !!
I think that product creation is done very well. The position of the Screw hole is properly shaped and perforated properly, so I think that the installation work can be done easily with Bolt - on.
However, in NORMAL, since the Clip part fixing the Front cowl part is omitted in GIVIScreen, the mounting part of Cowl can not be firmly fixed. In products of other companies, there is a product with a Clip part, so if you omit it for Cost reduction, I feel lame strange regrettable. At the time of installation, I did not know why the Clip part could not be fixed, I was worrying. I do not mind the price getting higher so I'd like to sell Screen with Clip part.
View detail
Fits: Others E370, Others E108
The electric lamp Type arrived. I wanted LED Type ...
The electric lamp Type arrived.
I wanted
LED Type ...
View detail
Contact with a box thinks that it is one more. although play has a box a little, it is a relation of this play and switch on the light -- and -- sufficient -- it is .
Contact with a box thinks that it is one more.
although play has a box a little, it is a relation of this play and switch on the light -- and -- sufficient -- it is .
View detail
![Fitting For Mono Rack [359FZ]](https://global.webike-cdn.net/photo/article/30/1285509662530L.jpg)
Although the cut of a rear cowl is required to attach to a phasor, Every one right and left, 2 cm x about (it goes out simply with nippers) 4 cm, Since it appears in the instruction manual and the perforated line is contained also in the cowl side
Although the cut of a rear cowl is required to attach to a phasor,
Every one right and left, 2 cm x about (it goes out simply with nippers) 4 cm,
Since it appears in the instruction manual and the perforated line is contained also in the cowl side from the beginning perfectly, the place to cut for true -, [ easy ]
That there are two stars (although looked in, to the extent that it does not understand) which are not known by any means if it does not look in from the bottom even if cutting [ which wages had as I have you attach in a store / which is not ] temporarily goes wrong,
Although the drilling accuracy of the attached parts made from aluminum having been open at the place bad shifted for a while and these parts become a form inserted in the frame by the side of a car body, it is the point which only a few had to correct with the stick file greatly (it is aluminum, it deletes immediately and can correct).
View detail
He will be Colet if it is called the posterior matter lamp of GIVI. But a thing with much loose connection is a difficulty. He is Massey rather than there is nothing.
He will be Colet if it is called the posterior matter lamp of GIVI.
But a thing with much loose connection is a difficulty.
He is Massey rather than there is nothing.
View detail
It is simply attached only by making two holes as an attached paper pattern. However, although it is written in Italian and is [ other case and common sake ] a little unclear, a paper pattern has no problem, if it sees well. Probably because a lid
It is simply attached only by making two holes as an attached paper pattern.
However, although it is written in Italian and is [ other case and common sake ] a little unclear, a paper pattern has no problem, if it sees well.
Probably because a lid becomes heavy, in Tokoro with a large vibration, the Katha Katha sound comes out from a lid.
View detail
Pains were taken just for a moment not to write the description not much in detail, and not know a hang, but remove the top shell of V46. Although it was the used comment, when it was neither the time dark in the neighborhood, nor the inside of the tu
Pains were taken just for a moment not to write the description not much in detail, and not know a hang, but remove the top shell of V46.
Although it was the used comment, when it was neither the time dark in the neighborhood, nor the inside of the tunnel, even if it had switched on the light, I hardly understand.
(Lighting is known if this portion of the top case is seen carefully) They are two stars in the badness of this visibility.
probably, it was brighter if the ball was LED -- ~
View detail
Regrettable The goods were returned to Webike. I am glad! Although the photograph was taken, the trifling defect was found in goods. As for the left-hand side pannier, the emblem of GIVI has floated. Although the end is stuck, middle is vacant
Regrettable The goods were returned to Webike.
I am glad! Although the photograph was taken, the trifling defect was found in goods.
As for the left-hand side pannier, the emblem of GIVI has floated.
Although the end is stuck, middle is vacant as for it.
push and adhere -- although like, it does not adhere.
Into the end portion of the parts of right-hand side satin silver, although it may be a small thing, paint application unevenness (probably air bubbles) is discovered.
Since the left-hand side pannier was perfect paint application, even if compared, it thinks it is distorted.
Since it was a product made from an italy, he thought that it was unavoidable, but when it often sees, there is a crack which is attached to a red plastic part only by the very small needle ? and something.
Although the depth was measured at the point of the nail, did it attach during the work at the time of italy packing? In the quality level of an italy, it may be to there.
Although the fault of Mr. Webike of a vendor thinks zero, I was allowed to return the goods.
Since the GIVI V35N right-and-left set deer of yearning was also due to make stay by a one-off, it is dramatically regrettable.
since it paid on the point for about ten 10,000 yen by the point of the affiliate this time, he thought whether I could sell by Yahoo! Auctions as it is, but the purchased person judged that he was too much pitiful.
The state which is waiting for a deed point to come returned-goods work on the contrary promptly.
Although I am sorry at the work for the check mistake of people specializing in Webike of an importing agency, it is a store of the best products offered in Japan, and sense of security.
I was allowed to consider it as returned goods this time.
View detail