Reviews
To hide the hexagonal hole
Plating was peeling and falling apart, so the
Purchased to replace
It looks pretty shiny.
View detail
I lost it, so...
The push rivet that stops the side cowl of YZF-R1 was lost, so I bought it.
SizeExactly.
I looked at the Touring and a little bit of the Circuit and had no problems at all.
View detail
Exactly
SPGrade in Motorcycle MODEL owned by Reserver tank [Color] I thought it looked good in Smoke. I thought about replacing it with standard White since mine is a Standard Grade, but once I did this Cover, I thought I would never know. I thought about replacing it with a standard white one, but I decided that I wouldn't know if I did!
I was worried about the color of the base, whether I should choose Black or Blue with YAMAHA color embroidery, but the color of the base is Color.:Gray, I bought it because it was inexpensive and I thought I could change it if it was a failure. It's a very rudimentary customization, but I'm sure I'll grow to love it.
View detail
Copper Packing
I want to use copper packing for drain bolt when changing oil.
It was thinner and smaller than I expected.
There doesn't seem to be any oil leaks and the Seal is done, so that's good.
Quantity:1pc., cheap in terms of selling price? I wonder.
View detail
It is usable enough. Soft but not tight enough to lick.
It is often written that the six corners become rounded, but when I tightened them with the torque wrench by pressing the tool firmly, the corners were indeed slightly deformed, but not to the extent that they became impossible to tighten.
If you say you can't install it, it's probably because of poor workmanship.
If you discount it as a cheap product, it's not bad at all.
View detail
In Repair.
Installation was easy and problem free! View detail
I like the stuff, but I didn't need it for crf250rally….
Purchased when replacing crf250rallyBlinker
Rear blinkerMinus side connector is not the same shape as the light blue or Orange one, so I thought I could use it on the Plus side,
The Minus side is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used when replacing crf250rallyRear blinker
Used when replacing crf250rallyBlinker
LeftBlinker is Orange.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used for crf250rallyRear blinker
Used when replacing crf250rallyBlinker
RightBlinker is Blue.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Convenient
It is useful when you are not comfortable with drilling a hole to fasten a bolt or directly affixing with double-sided tape.
Examples of use include Income's Fix and Paste Type's Add Meter.
Especially when additional Meteretc. are attached with this, it is quite easy to attach and detach when something happens to Wiring-related.
View detail
Fantastic...
These small spacers are fantastic! The finish on the anodising and precision of the maching is perfect and they come in these wonderful little packages that are a joy to look at. They were great value too, compared to other options I looked at. Would highly recommend these if you are looking for spacers. View detail
Flashing installation
Purchased as a Spacer because the Blinker turns up
It might have been a safe win, but it turned out to be in front.
View detail
I've heard that OEMs are concerned about Rust.
When I replaced the master cylinder cap, I was concerned about the Rust on the pure Normal Thread Screw, so I purchased this one.
The delivery was fast and Large satisfactory, and after the exchange it is very cool without any discomfort.
Thank you very much!
View detail
It's beautifully made.
I purchased this for my Yamaha SEROW which has a round external Silencer installed.
I made my own back guard to be attached to the silencer to protect the back for long touring. I have been using this product for a long touring, but I have to replace my round silencer band with an oval silencer band because the stainless steel is very hard and it is difficult to use it for other shapes. In my experience, it takes a long time to bend stainless steel by hand or to form it into an oval shape, and the result is not good. Unfortunately, the round Silencer band has been put into temporary storage.
The product itself is fine and well made; it is made of 1mm Stainless steel flat plate machined to 110 pie inside diameter. The bracket is raised vertically from the circular shape and is hammered to hold a right angle. The cap bolt is 25mm long, 7.7mm in diameter, and only needs an 8mm mounting hole. The Elastic band is not just a black flat rubber band, but is made with a horizontal gap to prevent it from moving. The bottom of the engraved Bracket is clearly marked 110 Pi. This kind of workmanship is very helpful when you own several similar parts.
It is relatively easy to make round-shaped bands made of gold where there are machine tools, and other manufacturers also offer a variety of bands. KITACO is a good company that sells at a cost like ConveniencePartsSeries.
View detail
It was used for the production of the preliminary Tank.
I made a spare tank and used it to take out the Fuel Hose. m6Tap was cut and welded because I was afraid of leakage. View detail
It's kind of expensive.
I used to buy Vinyl tape for around 100 yen and used it for wiring, but after a few years the surface became sticky and I didn't like it, so I bought Harness tape, which is a little more expensive, and rewound it. I am looking forward to the future. View detail
for RepairWiring
Great cosmetics I wanted a Wiring like this and it was just what I needed. View detail
I wanted a Stopper in the middle.
I used it on a Gasoline sub tank, it's useful for connecting hoses together, but it's a bit unreliable plastic, so you don't want to use pliers or anything like that when installing it.
A stopper in the middle would have made it easier to use. I'd rather have an aluminum one or something.
View detail
KITACO Needle SIMM set 3×6×0.3/0.6
Used to improve Kyanopi's mid-range speed.
I think it is good because it is cheap and effective.
View detail
It's good.
It is available at most motorcycle supply stores.
Parts replacement, etc.
I replace them when the dimensions change, etc.
View detail