Reviews
It was very good!
The price is low, but the quality is very high and I had no problems at all with the installation.
I am considering purchasing another bottle in Stock!
View detail
Getting the Center out is the hard part.
I was prepared for BALI and Small scratches, but I can't get the Center without modifying the Brake Panel side.
I also bought a 4mm Sprocket spacer but I think it will be useless.
Also, there is some distortion, so if you want to assemble it tightly, we recommend a reasonable price.
View detail
I guess it's okay…
Stud bolt pulls out….
Not recommended for high Engine Displacement Volume!
View detail
Recommended!
After the replacement, the ride changed!
The one below was RustRust….
View detail
Wheels
Wheels are as described. Very nice finish. Installed on my 1984 Honda z50r. I would recommend these wheels to anyone wanting a modern look to a z50 build. The tires look very good as well. Looking forward to riding! View detail
Fits: HONDA MONKEY, HONDA GORILLA
Best value
Best value for the money and everything you need to install 10in wheels.tires already installed made it easier with less time invested View detail
Perfect fitment
These wheel spacers was exactly what I was looking for when I went with the 10in 3.5j rim attached to the stock monkey hubs. Only issue is you will longer hub bolts if you use all the spacers at once. View detail
Used in MONKEY
It is NTN, so no satisfaction or complaints. It is an ordinary Bearing. View detail
Buy to Restore
Purchased because it was sticking?
I recommend it because once you change it, you won't change it often!
Better turnover!
View detail
Fits: HONDA MONKEY, HONDA GORILLA
Take it up with GORILLA!
I went with 10Inch, although Touring is fine.
Not so good for city driving?
Custom feeling is up!
View detail
Purchased as for Repair
The bolt on the front axle shaft was licked and could not be removed or retightened, so I purchased it for replacement. I bought it because I thought it was equivalent to OEM and installed and replaced it. It is a product that can be used like OEM from city driving to touring and has good cost performance. Of course, the low shipping cost was a plus. View detail
OEM Style has this
I recommend it because 4-hole thick Wheels are hard to find.
Gee Craft is discontinued
View detail
Sufficient for city driving
It should be sufficient for city driving.
Bearing is JAPAN
Might be safer than a 30 year old OEM used one. (as in a thing) to be taken care of
View detail
It's cheaper.
I replaced the Bearing on my Monkee 50's rear wheel, I had to buy a special tool to replace the Bearing, which cost about 3000-6000 yen, so I did it the old fashioned way. When you put it in, be careful to put it in straight, that's the hang I've been doing.
I'll be happy if this gets me a little better mileage!
The Bearing is the same part number as the OEM, but I think it is a little more expensive than the Home center, but the Home center near me didn't have it, so I bought it because it was too much trouble to look around. (Maybe cheaper than OEM Parts?).
Also, with the purchase of Bearing, the old Minimoto's Image is gone.
View detail
Almost no change from OEM
I used it for my MONKEY.
Nothing different from OEM. I have no complaints. If I had to say, I think the surface treatment is a little cheap, but I haven't seen any rust floating around after 6 months of use.
I was worried about the roughness of the accuracy made by Large land because it is cheap, but there was no problem with the screw thread and Beauty.
If I had to say something, I would say that it comes in a Vinyl bag, so distortion and scratches are a bit of a concern. However, if you are sensitive about it, you should look for a domestic manufacturer.
View detail
Commonly usable
Replaced because the screw thread of the mounting hole of OEMDrum became stupid
I was a little uneasy because it wasn't an OEM product, but the effect of Brake was much better than before the change is better (Maybe it's too much because I didn't change the Brake situation because it was left unattended for decades and I changed the Shoe at the same time )
But there was a little BALI in the holes and molding, so I had to remove the BALI before putting it on The rating is slightly lower due to the addition or subtraction of
I think the performance is adequate
View detail
Not that great
This axle is low priced, which is great. But the finishing on the head looks terrible, and because of that I will not put this axle on my bike. So for me this purchase was a waste of money. I'm normally very satisfied with parts from Minimoto. They have low prices and you usually get great value for the money. I very much like the brand, but sorry Minimoto, this axle was a big disappointment. View detail
Fits: HONDA dachshund, HONDA dachshund
For Tubelessization!
When Long touring on DAX, it was Puncture.
I can not think of going out with Puncture repair of the matching Wheel - - -
I considered Tubeless there, but I can not find a perfect Wheel.
As a result of various studies, we used this Wheel and converted it to 12inc and coped with it.
I checked the delivered Wheel, but it is better than I thought.
There are some somewhat somewhat complicated parts, such as the finishing of Edge, but it is enough to think about the price.
Tire selected by Set is Michelin's "POWER PURE SC 110 / It is 70-12..
Firstly, when weighing with Wheel with a bathroom scale, weigh 4. 6kg.
OEM+Tube+DunlopD307 (10inc) Is 4. 9kg - - - I did Inch Up
Weight reduced 300 g! This can be expected.
When braiding in the hub, baptism of Chinese quality immediately - - - Rear's hub and Wheel
I can not fit snugly. Hub and Wheel interfere about 1 mm.
Since it can not be helped, we cut off the side of Wheel with File, and at the end we joined with hub and Bolt by force technique.
The Front was able to be assembled smoothly without difficulty.
This time, Wheel is 3. I made it with 5J, but this size is NORMAL Front fork,
It seems to be a limit to combine with Swingarm.
Especially on the Front side, Clearance with Fender's Screw is only about 1 mm
It would be better if you could replace it with low head Bolt.
The outer diameter was about 20 mm as well, but it became Large, but STAND (Main, Sub) Both
I managed to use it as it was.
The impression of trying to run - - -
It became a modern ride like a light Truck turned into a passenger car!.
Especially the ride feeling has improved very much.
I do not know whether lightening has worked or whether changing Tire has worked,
Anyway, I think that it was good to exchange.
One note, I will write a note.
Since the thickness of the portion to be joined with the hub of this Wheel becomes much thicker than the OEM, it is necessary to prepare Bolt 5 mm long 30 mm.
Chinese Parts did not trust much, but this time Wheel was satisfied with Large.
But Valve is not talking about Naisho which replaced Wheel's accessories with domestic Valve!.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
It's less expensive.
The accuracy is the worst.. Since the hub does not become the center of Wheel, turning Wheel up and down about 1 cm.
In addition, Rim is also.
Try running and 80 km / Vibration comes out from about h.
I replaced it with GCraft.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
There is nothing you can not use
I was attaching this product and the same Manufacturer's hub at the same time
The hub was the worst
So I changed only the hub to domestic production
I thought that the suspension was wrong
It was a feeling that there was a problem with the accuracy of the foil itself
Because I am running with my own 100 kilograms in combination with domestic hub, this product
I think that there are no fatal defects in running
There are quite a few vibrations
The built-in Tire is not bad, but the inside Tube has leaked about 1 month or so
For the time being, I think that it is a good product in terms of cospar if it only converts to 10 Inch
I do not want to use it for too long term
In fact Wheel changed to a famous FOR JAPAN MODEL Manufacturer item
View detail