Reviews
Fits: YAMAHA SR250, SUZUKI 250SB, HONDA 250T LACustom, HONDA AX-1, HONDA CL135, HONDA CL350, HONDA CL72, HONDA CL77, HONDA CM250T, HONDA CM400T, HONDA CRM250AR, HONDA CRM250R, HONDA FTR223D, HONDA FTR250, HONDA GB250 CLUBMAN, HONDA GB400TT, HONDA GB500TT, HONDA MT250ELSINORE, HONDA MTX125R, HONDA MTX200R
Does not fit the KL250 Sherpa.
The Manufacturer's list of compatible models says it is compatible with KL250 Sherpa, but that's too long.
If installed normally, there will be excess
The quality of the product itself is not bad, so I think it will be fine for cars with longer forks.
KL250 Sherpa's Fork outerTop to bottom of trident is 240mm
Catalogue value WheelTravel is 230mm
100mm remains above the Outer even when shrunk the most without processing.
This would make Stroke about 130mm.
If it was just for Inner Tube protection purposes, it would be fine, but I don't think it is, so I cut it off, even though it will look very ugly lol.
In hindsight, I lightly regret that using the top half wouldn't have made it so ugly.
However, even in this state, the Stroke will be reduced by about 50mm
Boots itself becomes Bump rubber.
Even other companies' products that say they are compatible with KL250 Sherpa are quite long.
Would it be better to just use a shorter product with more extension?
Maybe I'm losing my mind, but I'd like to find a good product!
I bought it + even processed it so I'll be using it for a while lol.
View detail
Recommended
Easy to replace, cheap!
Recommended!
View detail
Fits: HONDA GORILLA, HONDA MONKEY
Recommended!
Purchased to fit 12-inches.
Well made, Caliper is the same as ksr, so you can change Caliper!
Stems were cut down to the largest size and lowered.
It was a little soft, so I changed the Oil!
View detail
This is an OEM type, so it fits just right, the construction is solid, and I think it's very durable It is
The cheap ones made in foreign countries have a thin bellows part that tears easily It was This is a low price, but the build quality is very solid The look and feel of the bike has been refreshed and I am more than happy to enjoy riding it it has become 。 View detail
Fits: HONDA GORILLA, HONDA MONKEY
Goring
Until now, when I was looking for Front fork to make 10 inc in Size up, it was FTire 8 inch, so I happened to purchase for 10-inchesInverted Front Fork, so I bought it. If you have experience of disassembling and maintaining a little bit of Mongoli, I think that we can incorporate it in about half a day, I think we can put together in Steering adjustment, retightening etc. in one day. (Depending on embedded experience as well)
Looking at the installation method such as Net, everyone was written that Fork oil was dirty and dirty, Fork seal was deformed and Fork itself was bent, so I tried all the way for the time being However, Fork oil was beautiful, there was no deformation of Fork seal, and there was no distortion of Fork Body.
Fork oil was exchanged because it was drained when Rose. Although it runs with built-in installation for the time being, since Caster angle and wheel diameter also change, straight running performance is good
Becoming not to pick up Gap, it is said that it got better looking, the disgusting place is better if the total length of Fork is a little more short, the disc is attached to the Left Side so Brake hose is strange to be harvested I will change it later when I exchange Mesh hose.
I think that it is a product that can be convinced if this equipment at this price, if it says that this product is disgusting, we recommend a product with a price 5 times to 10 times or more.
View detail
Let's use it properly
In order to change the height and angle of Rear suspension, I tried using it although the model is different, but after all it did not go well.
Some people attached it with a similar feeling.
I think that it is a good Parts that can be used quite well if the car models fit and use properly.
View detail