Reviews
Fits: KAWASAKI Z250, KAWASAKI Ninja400, KAWASAKI Z400, KAWASAKI Ninja250
Higher than BABY FACE
Except for the footpeg and heel plate (and color), it is the same as BABY FACE. The cost is about 12,300 yen higher than BABY FACE, so the cost performance is not good. I am satisfied with the color and position.
The car Both SidesChange arm uses the original OEM Product, but of the 9 companies I checked, only BABY FACE and YOSHIMURA did not make a dedicated change arm. I was concerned that the shift rod was leaning, so I installed Striker's Change arm and adjusted it by 2mm with a washer, and it became almost parallel to the car body.
Well, I don't think there is anything wrong with it being tilted, but I am concerned about the way it looks.
Footpeg is made by JagerLauftK.M.T. I like it, so I changed it. Also, the Brake Switch Bulb on the Right Side looks like an afterthought.
I wrote what it is, but I like it a lot.
View detail
Beautiful Yoshimura parts
Parcel received in France very quickly, barely a week. The package is very well packaged and protected by Webike. The Yoshimura box is well made and the pieces inside are protected so as not to scratch each other. For the pieces themselves, well the Yoshimura quality is there, the pieces are gorgeous, the finishes perfect, the logo detail discreet. I am very happy with my purchase, I can't wait to install them. View detail
Attention ??
Brake switch recommends hydraulic pressure.
Also, the mounting bolt interferes with the chain slider, so countermeasures are needed.
View detail
For GSX1300R HAYABUSA
[How is it used?
Installed on GSX1300R HAYABUSA
With OEM, the angle was not adjustable, so my knees often hurt when I rode long distances.
This one is very convenient because it can be adjusted to various angles.
Was the one you received as per Image?
Yes, exactly as pictured.
The box design is perfect.
As expected of YOSHIMURA.
Was the installation difficult?
Instruction Manual is included, so if you can replace the oil to some extent, this one should not be too difficult.
How was your experience with it?
YOSHIMURA is the best
feel well
[Included Parts:were they on?
Instruction Manual、Sticker
[Was there anything that disappointed you?
It's a bit expensive
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Not particularly.
View detail
Fits: KAWASAKI Z250, KAWASAKI Ninja400, KAWASAKI Z400, KAWASAKI Ninja250
The product itself is 4 stars.
I have few complaints about the product itself, but I do have a complaint about WEBIKE.
*In the unlikely event that a footpeg is damaged due to a fall or other accident, Product Contents can be purchased as Repair Parts.
is stated in the product information section, but since the products purchased from WEBIKE could not be registered with YOSHIMURA OnLine, we cannot purchase the main parts that might break when the product stumbles. If it stumbles, we will have to repurchase the entire product.
As for the product, I am concerned about the poor return spring on the Brake lever and the price is high for a BABY FACEBrand. I am satisfied with 4 stars for the product only.
The only differences from BABY FACEBrand are color, footpeg shape, and heel plate shape.
I would recommend BABY FACE to those who are not particular, but I am satisfied with my purchase because I adore YOSHIMURABrand, even if it is expensive.
View detail
Detailed design in all aspects and smooth gear pedal operations
About quality and texture, I can confirm the quality great and the material used is aluminum that is CNC machined to shape and finished with an all dark gray anodized coating.About the feeling of use, Detailed design in all aspects and smooth gear pedal operations are a massive improvement over the original Honda footpeg parts.Products to buy together, Yoshimura make a limited range of high quality parts for the Monkey 125 and the addition of their fender eliminator bracket would be ideal to also add to your cart to further refine the Monkey 125.Difficulty of installation, I can say the fitment of the footpeg kit for my installation was easy due to the ease of access to all the mounting bolts and included instuctions on how to assemble the kit.Cost performance and comparison with other products, The pricing of this product is good, you receive parts made from high quality materials and with a higher quality finish them most others offer. There are cheaper and higher priced options but I find the Yoshimura product the best compromise.About shipping and packaging, My order was shipped within 24 hours of the product being in stock and I received a few emails advising me of the status up until the order was dispatched. The order arrived within the estimated date range and was extremely well packaged. I found the link supplied to track my order very useful while I was waiting for the order to land in the country. Any concerns, cautions, or advice when purchasing, I have no concerns or cautions when purchasing from Webike. I cannot recommend Webike enough for the majority of your biking needs. They not only sell aftermarket parts and bike gear but also OEM parts for your repairs and servicing needs. View detail
Pretty good
Pros: - Provide better riding position. - Does not poking at my calf when I stop the bike and stand up right. Cons: - a little hard to install with OEM exhaust. View detail
I use it while making adjustments.
The appearance Parenthesis is excellent.
When the Stop-lamp was turned on perfectly, the Rear brake became too sweet, so I adjusted it with ChocolateChocolate.
The GEAR is in perfect condition.
The footpeg is firmly processed to prevent slipping, but the cutting on the part facing the ground is sharp, so care should be taken not to cut your hand when installing it.
View detail
product
Excellent product. Fit with my mt07, fast shipping.. Fit with my yoshimura r11 exhaust. Very enjoy with this purchase. View detail
To HAYABUSA.
Good without exaggeration! Satisfied overall.
However, when operating the clutch, the soles of the shoes and the side stand (when lowering the footpeg) hit each other, depending on the position of the footpeg, etc.
Thick-soled shoes will be tough.
View detail
OEM-like natural look and feel
Purchased because I replaced it with Yoshimura cyclone.
I was originally going to purchase the Exhaust System from here, but the quotation said it was not available. I bought the Exhaust SystemBody from the manufacturer and the Off-set Plate from webike.
The bolt tightening was done by the shop with each Exhaust System replacement because there was a specified Torque.
I like the finish, it is so natural that you can't tell unless you are told.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI KATANA, SUZUKI KATANA
Quintessential YOSHIMURAQuality
Handlebar is low-positioned and footpeg position is introduced uncomfortably.
In any case, it is highly flexible, and any body type will be able to obtain a satisfactory Position.
However, when installing the footpeg, be careful to remove the OEM footpeg, as the screw lock may be sticking around the footpeg.
I had a bolt on the Right Side that was almost licked off, and I had to use a shock driver to get it to come off. If you do not have the tools or confidence, it is safer to ask the shop to install it for you.
The effect is immensely Large.
It is very easy to maneuver and turn.
Riding has become so much fun that I wish I had introduced it earlier.
View detail
Improved operability
Installed to improve the operating feel rather than to change the position.
The rattle-free Pedal and biting Footpeg provide a good feel for the operation.
The Position is quite high, so my 178cm height, combined with the low Seat, made it a bit cramped.
Spare parts are set for all of them, so they are safe even in case of breakage.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
YOSHIMURA of the world
[How is it used?
Mainly touring
Was the one you received as per Image?
Better than I imagined.
Was the installation difficult?
First time replacing the steps and it wasn't easy for me, but the installation went almost smoothly.
How was your experience with it?
Was good
[Included Parts:were they on?
It was there.
[Was there anything that disappointed you?
Instruction Manual is difficult to understand
View detail
YOSHIMURARear Sets
Anyway, it's so cool!
I managed to install the Shift side, but could not install the Brake Side by myself, so I asked a Motorcycle shop to do it for me.
I would like to try various things about the Riding position, which is highly effective in preventing footpeg slippage.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI KATANA, SUZUKI KATANA
YOSHIMURA Footpeg Kit X-TREAD KATANA
It had been out of stock for a while, but we got it with a BackOrder at Weig.
Installation, while simple and DIY possible, requires some tools, so those without tools are recommended to install at the Shop.
The shift rod has become thicker and the entry of GEAR has become very smooth.
After all, YOSHIMURABrand.
The details are well made and yet beautiful.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Interference with Exhaust System
It interferes with the Exhaust System and leaves the Brake pedal with almost no adjustment range.
CSR Full Exhaust System Up type
I think it's OK if it's YOSHIMURAExhaust System, but you can use the Back Order at ・・・・・
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Z900RSStep Kit X-TREAD
That's Yoshimura for you.
I am satisfied with the appearance and operability.
Riding position was also obtained with precise movement.
Large Satisfied
View detail
Misprinted instruction manual?
I had it installed at the Shop and they had a few Bolt dimensions that were wrong in the instruction manual!
If you rely on the instruction manual for installation, you may have a hard time.
View detail
More cohesive than OEM
I have never had good memories with Rear Sets, so I have always been an OEM footpeg supremacist. The GSX1300R HAYABUSA footpeg has rubber on the top of the footpeg for long distance travel. I'm glad I bought it.
I used to ride on the OEM footpeg in a pseudo-Rear Sets position, but after the replacement, I can ride normally, so I can operate the Shift and Rear brake normally, and the feel of the Shift change and Rear brake is very good, and I am very satisfied with it. The price is high, but this tight feeling is a recommendation because it is a place that is always used in motorcycle driving. The color is also good, and if you look at it from a little distance, it is very well put together and visually satisfying. By the way, the Pillow ball part is exposed, but you can remove the OEM rubber cover and reuse it as it is, so it is a recommendation.
View detail