Reviews
Fits: HONDA Today, HONDA Today, HONDA DIO(4Cycle), HONDA DIO(4Cycle)
Repair is completed at a low cost!
Installed on ThirdMotorcycle's Today that goes to the nearby Convenience, replacing an OEM OEMRear Suspension that had been scuffed up and deteriorated. The price is very low, but I have had no problems with it! I am Large satisfied with the low price and the refresh! View detail
neither good nor bad
I purchased this for my RC42. However, I could not install it as it is because it was a driving school spec. I modified it and installed it. However, it became Fixed Type which cannot be folded. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA
APE100 footpeg replacement
I used it to replace the footpeg on my APE100. It looks much better now. The screws that hold it in place seemed to come off easily, so I applied Screw lock and installed it. Installation was easy. View detail
Cost-effective product
CUB100 THAI style rear suspension.
Full Plating, Simple and beautiful.
This is quite a Recommendation.
good point
Simple design.
Cheap as outside of the company.
● Solid, so no problems with Tandem, loading, etc.
Corner is also easy.
A bad point
Rust is easy to find.
Rust is easy to get out, but it can be removed quickly with an abrasive or something similar, so it is easy to clean. I think it is better than YSS.
View detail
Fits: HONDA Today, HONDA Today, HONDA DIO(4Cycle), HONDA DIO(4Cycle)
Exchange from OEM
OEMSuspension by DioFit.
After 24 years, he must have passed away;
So I chose this as an inexpensive replacement part.
Just remove the Air cleaner and SeatBox and you're good to go.
There will be a slight rattle on the lower mounting part.
I think the Point is to bite one Washer.
View detail
Fits: HONDA Ape 100, HONDA Ape 50, HONDA Super Cub 90, HONDA Super Cub 90, HONDA Super Cub 90, HONDA wallaroo, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB70, HONDA SUPER CUB70, HONDA solo, HONDA DAX70, HONDA DAX, HONDA BENLY50, HONDA BENLY50, HONDA APE 50, HONDA APE 100
Installed on TOWN MATE 90
It's for the CUB, but it can be attached to the TOWN MATE 90.
Just paint G17 Bond and put it on
It is recommended to stop it with Bond because it moves when you stand and ride on the ground though it is large and strong even if you do not use Bond.
View detail
Fits: HONDA Ape 100, HONDA Ape 50, HONDA Super Cub 90, HONDA Super Cub 90, HONDA Super Cub 90, HONDA wallaroo, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB70, HONDA SUPER CUB70, HONDA solo, HONDA DAX70, HONDA DAX, HONDA BENLY50, HONDA BENLY50, HONDA APE 50, HONDA APE 100
Set of rubber footrests
I put a set of rubber footrests on a Yamaha YB-1 Four, rated it 4 due to the fact that this product has a lot of plastic and because of this it is too rigid. I put a set of rubber feet on the Yamaha YB-1 Four. I rated it at 4 due to the fact that there is a lot of plastic in this product and because of this it is too hard. (Translated by Google Translator) View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125
It is not a decoration.
Because Address 125 S is lightweight
Because it is around the Front where the rigidity is insufficient,
Vibration reduction and Corner's improvement of driving stability etc.
I thought that the effect was easy to understand.
If you are a car that is originally well-built
The effect is difficult to understand
I can not deny the possibility of ending with things like decorations
Address is a decorative Parts.
View detail
Fits: HONDA Ape 100, HONDA Ape 50, HONDA Super Cub 90, HONDA Super Cub 90, HONDA Super Cub 90, HONDA wallaroo, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB70, HONDA SUPER CUB70, HONDA solo, HONDA DAX70, HONDA DAX, HONDA BENLY50, HONDA BENLY50, HONDA APE 50, HONDA APE 100
Soft and comfy footpegs
I'm very happy with these and recommend them to anyone riding without protective MC boots. Good grip and very comfortable for the feet, even when standing up riding off road. And no problem hitting your leg against them. I've done that several times and been very glad they are "softies", and not sharp metal. Also the rubber quality is great and stays as new for many years without wear and tear. Top notch product, cheap and definitely a great buy. View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125
Necessary to fit outside Fork outside the device
I did it! The thing is firmly not BALI, I think that it is a good product, but the diameter does not fit to the outside Fork of my vehicle Oversized.
We are adding Color suddenly.
Still rigidity Up pushing around the Front was able to experience it and I was able to use it without any problem in terms of performance.
View detail
What is it and what are you doing?...
Although it was used with SUPER JOG Zr 3 YK, since Length is longer than OEM, when using Center Stand, the vehicle will not be stable unless it is a firm flat place. Although it is a feeling of use when driving, there was absolutely no anxiety or dissatisfaction. (The factory default setting was fairly solid) As an aside, I stuck OHLINS Sticker...
View detail
Fits: HONDA DIO (2Cycle), HONDA DIO(4Cycle), HONDA DIO(4Cycle), HONDA Giorno, HONDA Today, HONDA Today, HONDA LIVE DIO
Because it is made in China
I bought it for LIVE DIO's for Repair.
If you compare the OEM Parts Number and compare it, since there is an opening of more than half-value, we chose this person for the time being.
As for the finish, it is a price, so excessive expectations are forbidden.
Valve hole circumference etc etc. , BALI or sharp parts stand out, so I think that it is better not to touch easily with bare hands.
Also, it is better not to leave BALI and so it needs to be processed and partial painting required.
I can not do the same attachment as OEM, but I think that it is supposed to be made in Chinese.
View detail
The price is reasonable
Making fine is the worst. Rear cut and processed to be along Exactly.
Although it is a Type that bends by yourself, Front has no problem at all, but Rear needs to bend to various angles considerably because it catches up to the edge of footpeg, and processing is Large strange. Perhaps it can not be installed neatly for beginners?
At least Rear is required to improve because there is no need to bend with Kunekune if it is paste only a part.
Rear will be able to see the Screw hole at the end to change to Step Board later such as DAYTONA.
View detail