Reviews
Fits: HONDA Africa Twin Adventure Sports ES, HONDA Afriva Twin Adventure Sports, HONDA Africa Twin
AFT 1100 OEM Quick Shifter
Perfectlly working mainly from 2nd to above gears. 1st to 2nd still need some adjustment or skill improvement. Anyway very easy to install (detailed instructions) and configure. View detail
Even if it's not a low-headed Bolt….
I purchased this to improve the hardness of the entry of Shift on my 2014 NINJA1000, which had been bothering me since I bought the car used.
Installation could be done without removing the Cowl, so it took only 5 minutes.
However, when installed with the supplied low head bolt, it does not interfere with the OEM change lever, but there is only a gap of about 1mm, which bothered me, so I installed a M6×10 button cap bolt with a lower head than the low head bolt to secure the gap.
Shift entry remains a little stiffer than before, and I feel that the shift feel has become tighter.
I wish it were a little cheaper because it is expensive for such small parts.
View detail
Nice simple solution
much better than using sealant or silicone if you forgot, like did, to fill the rim lock hole before installing tube and tire. Nice simple solution for plugging the extra hole when 2. rim locks are not used.Using these to plug the extra hole in a rim makes the job easier and looks like it came from the OEM. These may be little things, but it's the little things that count to finish a job correctly. View detail
Fits: KAWASAKI ZZR1100 D, KAWASAKI ZZR1100 C, KAWASAKI ZX-10, KAWASAKI ZRX1200, KAWASAKI ZRX1100, KAWASAKI GPZ1100 , KAWASAKI GPZ1000 RX
Black will not fit without shaving due to the thickness of the surface treatment.
I cleaned up the cist Shaft with Paper but it was too tight to fit, so I had to rub the Bearing Inner Ring with Paperetc. a lot to get it in, although not enough to drop the Plating.
The reason may be the thickness of the plating, since I purchased it in black, but after inserting it into the Shift shaft, it turned smoothly, so it may be due to a slight thickening and deformation of the splined area near the shaft due to processing distortion.
The bearing was also reluctant to move, but after placing it in the shift shaft, it rotated smoothly, so I decided that the bearing would rarely rotate and assembled it as it was.
It would be nice if the price was a little lower.
View detail
Fits: HONDA MSX125SF, HONDA MSX125, HONDA MSX GROM, HONDA GROM
On the Grom JC92.
I feel that the Pre-road only adjustment is not enough.
The price seems to have gone up quite a bit compared to a while ago.
With this quality, you can get about 12,000 out of it.
Oil damper moves too fast by far when assembled and moved.
Orrifice is too Large in both COMP and TEN.
There are higher-end models with full-length adjustment, but as shown in the photo, the NORMAL and
This is fine for JC-92 as it does not change.
I was going to build it in inverted and lighten it under Spring, but Pre-road.
I gave up before I started messing with it.:If you get a Set, it can be the other way around, but it's pretty good.
I guess I don't care about this level of low-cost products anymore because I will remove parts.
When I first built it with Spring free length, it sank 1/2 of the car body with only 1G.
Finally, the Pre-road comes to the photo.
Originally, sagging was a bit of a hassle since the strokes were extremely short.
Tomorrow I will also tinker with the ZX-14R.
View detail
Fits: KAWASAKI Old Z series, KAWASAKI ZEPHYR1100, KAWASAKI Z900 GP ALL, KAWASAKI Z1000R, KAWASAKI Z750GP, KAWASAKI Z1-R/Z1-RII
Color:Only Yellow was in stock.
I wanted to change the spring color to black, but I was sure that I would have to change the spring during the setup anyway. I chose the one that I could get as soon as possible, even though it was not the color I wanted.
Looking at the recent exchange rate situation, it is impossible to know when the price of OHLINS will rise sharply, so it is better to buy it immediately when you need it. YSS, etc., which used to have an advantage in terms of price, are no longer items that can be bought randomly for cosmetic reasons.
I used it on my Ducati MHR900, which is a custom vehicle with no swing arm and no rear shock, so I don't care about the compatibility anymore. I used the Z suspension because of the weight of the vehicle and the overall length of the suspension. For the diversion, the M14 hole on the upper mount was converted to M10 by making a collar.
This one for Z is ride height adjustable based on 350mm overall length, but if the overall length that looks good is going to be 330mm or so, I plan to replace it with the shorter overall length OHLINS I have for my GSX1100S.
By the way, the Spring part number has changed from the previous one, so I checked it out and it seems that there has been a slight Spring Spec. change. I hope it has not changed so drastically, though I feel it is troublesome to check with the past Data.
As a reQuest to WeBig
I wish you would specify the total length of the suspension and the diameter of the end eye for Shock in particular, as there are many cases where it cannot be used on custom vehicles even if the model matches.
I would like to see SpringSingle Item for Setting, Lock nut for consumable parts, dampers of different lengths, etc. NAPS sells them.
Since this is a high-end product, please use a sales method that does not end with the sale of the product hanging.
View detail
I am happy with the fitment on my FLHR2016!
You will not regret purchasing this Rear Suspension.
The OEM Rear Suspension is for Americans, so it feels quite stiff to Japanese people, but this Rear Suspension is quite flexible and moves well, and the ride quality improves. Even an amateur can feel the difference.
The input when going over bumps at high speeds is clearly different. I think anyone can experience this.
The only drawback is that when I installed the Rear Carrier with DockingHardware, the inside of the top of the Suspension and the Rear Kiya Rear interfered with each other, resulting in scratches and dents. If you are using DockingHardware and already using the Rear Carrier, be careful.
View detail
Fits: SUZUKI ADDRESS V100, SUZUKI SEPIA, SUZUKI SEPIA RS, SUZUKI Address50, SUZUKI AddressV, SUZUKI AddressVTune, SUZUKI Address Tune, SUZUKI Address, SUZUKI Address Way, SUZUKI ADDRESSV125, SUZUKI HI-R
Cospar good
I changed from an OEMSuspension over 20 years ago to this product and it looks so much better.
When the throttle is opened, the rear tire grips the ground firmly through the suspension, and the driver feels a pleasant sensation of acceleration as if kicking out.
The Spring strength can be adjusted with the Hook wrench in about 4 or 5 steps, but I think the weakest state is sufficient.
LargeSatisfactory results for a few thousand dollars! Do you think it is cost-effective Outclassing maintenance?
View detail
Stroke sensor
It took a bit of time to install the Spring, but it was easy. View detail
I used it on my CBR1000rr-r SP.
I purchased these to match the lowdown on my CBR1000RR-R SP.
I used only the Short Stand. The installation went without a hitch.
It would have been better if the material were aluminum, as it would have been lighter.
Short might be better. Also, if the Plate is wider, it might be better not to have to attach an after-attachment Plate to prevent it from tipping over.
View detail
Fits: KAWASAKI ZX-4R, KAWASAKI ZX-4RR
Effective in reducing Rear sinking
Even if the sag is adjusted, when the load is applied at circuit level, the rear end sinks and the car turns weakly in the secondary turn, so dampers are necessary. I purchased the 4RR exclusive product because it was available this time. The most Large 3.5cm height of Rear is raised. 。 Since the frame position will be relatively higher, it is safe to raise the frame up to 2 cm, since it will lean more deeply when parked on the side stand. View detail
AELLAShift holderNINJA1000SX
Easier to install than expected.
I think I'm going in with GEAR or Snap.
Cospa is not that high.
View detail
Fits: YAMAHA YZ450FX, YAMAHA YZ250FX, YAMAHA YZ450F, YAMAHA YZ250F, YAMAHA WR450F, YAMAHA WR250F
Consumables Replacement
I had one on my previous Motorcycle. Replaced with this one again.
The finish is not as good as it should be because it is resin parts, but it is sufficient for the needs.
Fitting is also no problem.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-4R, KAWASAKI ZX-4RR
Happy to reverse shift.
”Reverse Shift is not possible with the Automatic shifter. "Oh, really …" I can't believe that the Reverse Shift, which can be done by changing the Shift arm up and down, is not easy to do! After some research, I found that the Sensor of the Shifter does not respond to the angle at which the Shifter is mounted. I was looking for a footpeg that could be used for Reverse Shift, and I found Babyface, which is compatible with Reverse Shift from several other companies, but I had to buy it as a separate part, and the cost was really low. The feel of the product is solid and very good. I don't feel that it is cheap in any way. The only thing that bothers me a little is that the tips of the Shift and Brake are hard.:I would have preferred Rubber since it is made of Plastic. But don't worry, it won't hurt your feet at all. By the way, the compatible car model is -22 years old, but it can be installed on the latest model 24 years old without any problem. I asked Webig to confirm it for me because I was worried about it. Thank you very much! View detail
Fit feel on par with OEMs
Thank you very much for the Chain tensioner. The installation is completed by Bolt On, but I adjusted the tensioner by overlapping the attached washers so that the chain would be more centered on the roller. In my case, I used all the washers to get the quantity:I was able to set it. I could not feel the running performance, but I think it is useful to reduce the flapping of the Chain. However, since the tension is not always applied by Spring, it is necessary to adjust the tension of the chain. Just a little... View detail
Fits: HONDA NS-1, HONDA NS-1
for Race, it seems.
I didn't like how thin the swing arm of the NS-1 was back then, so now that I'm a large person, I decided to secretly buy one without telling my wife and secretly install it.
The design looks good, the Installation Instruction Manual is missing and I know that I have to buy it.
"For Race" and the enclosed handwritten paper stated (^_^;)
I thought it was very important information that I wanted to know before I bought the car. I am a little worried.
View detail
Fits: HONDA SUPER CUBC125, HONDA CROSSCUB110, HONDA CT125CT110 HUNTER CUB, HONDA SUPER CUBC125
Front feels lighter!
I changed it along with the Front Disc replacement.
The weight is light, but the front tire feels lighter than expected!
The price is reasonable, so if you are not sure, try to replace it.
View detail
To the Accent around the Rear tire
This is the accent as seen from the rear view. View detail
Fits: HARLEY-DAVIDSON SPORTSTER Family, HARLEY-DAVIDSON DYNA Family, HARLEY-DAVIDSON DYNA Family
Used for GSX250E
I bought it knowing that it does not fit. The inner diameter is 39Φ and the inner diameter of my car is 33Φ so naturally it is loose, but since it does not fit the outer diameter due to the Stubby installation, I dared to fix it loosely so that it can move freely up and down. The Inner is short and not traveled a lot, so it works well as a protector to protect from stepping stones on the Dirt. View detail
Fits: Others , HONDA TODAY, HONDA TODAY, HONDA DIO(4Cycle), HONDA DIO(4Cycle), HONDA DIO (2Cycle), HONDA DIO (2Cycle), HONDA DIO (2Cycle), HONDA DIO (2Cycle), HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA Giorno
I wasn't expecting it.
I bought this as a rear shock for my old Scooter.
The Machine is Honda's first LEAD80.
Thank you very much
View detail