Reviews
Very well.
Nothing to say about the fuel tap of the kawasaki 750 zephyr. Perfectly replaces the original gauge without any unpleasant surprises. -------------------------------------------------- -------- Nothing to complain about the gas tap of the Kawasaki 750 Zephyr. Perfectly replaces the original gauge without any unpleasant surprises. Powered by Google Translator View detail
Satisfied
Good cost with 3 different sizes View detail
Looks like they're improving. (^^) Used for 4lInitial Model
I didn't like the Cook on the bottom out and ended up here.
First. RES-OFF-ON." is strange! I have heard that the display of "☆" is strange, but it seems to have been improved, and the one I purchased had the characters in the display. The image is also before the replacement.
I had no problem installing and using it. The switching operation is also well done, and I personally do not feel that it is cheap, etc.
Incidentally, I did a rose before installation, and the internal packing is also in line with the OEM, so I am not worried about the after installation.
I was curious.
There is a BALI at the Cock outlet and the inside diameter is narrow. The intake port at the time of ON is narrow and it seems to be hard for fuel to fall out. The mesh part of the Strainer is high, so fuel may remain.
Right. Well, as far as the others' are concerned, I guess there is no problem….
View detail
Filtration capacity is unknown but to prevent Rust contamination.
[How is it used?
TZr250R (3XV) It is used for
Although 10mmSize Filters are hard to find, we chose this product from Brand, which is one of the most inexpensive and reliable.
Was the one you received as per Image?
It is larger than expected and takes up rather a lot of space.
L-shaped would have been better,...
Was the installation difficult?
It is simple to interrupt the Fuel line.
There is a direction, so you need to make sure that you do not make that mistake.
How was your experience with it?
I am not sure if the Filter is working properly, but so far I have not had any problems.
The transparent body allows you to check the internal condition of the product.
How did it compare to other products?
I've also used Daytona's Filter, but I'm not sure of the filtration capabilities of either!
It is safe to put it on an old car for now.
[Points to note]
Only the mounting orientation must be taken care of.
Also, be careful of the size, as it is quite large.
【Review】
I don't know about filtration capacity, but I guess it's better than nothing. I think it is.
10mm filters are not so common, and not many manufacturers offer them, but we were glad to find them in the lineup.
View detail
Yoshi Yoshi
I don't know if it was ordered from overseas or if it was a Corona thing, but it took a few months to arrive.
The construction and texture are very good and I think it is a very good value.
It has only been installed for a short period of time, so we do not yet know how durable it will be.
The vehicle is D1, but with Cook in the OFF position, the positional relationship is such that the Limit does not hit the Side cover.
View detail
Nylon meshL shape
There are many types of Fuel filters, but it is difficult and troublesome to know which one to buy at a glance.
I needed an L-shape for handling, but it was a hassle to find an L-shaped Gold genus Filter one, so I went with this one.
View detail
I bought a few different kinds.
I have been using PaperType so far, but I also bought Nylon mesh Type.
Nothing personal, but it is a little more compact, so handling in the vicinity of the carburetor is improved. The resistance is gone, but I am observing whether the Float chamber contains Garbage or not.
View detail
Something to have on hand to help in an emergency.
Used for hose of RadiatorReserver tank.
I originally purchased it for that purpose, but when the Fuel Hose died due to deterioration on the road and started leaking fuel, I used this one that I happened to have with me for emergency treatment.
Since Universal is expensive in terms of size, it would be a good idea to buy one for a processing base for now.
View detail
Fits: HARLEY-DAVIDSON Mainly used for oil lines.
Fuel line, this is the only choice.
Don't use hose, which is quickly altered by UV light, heat, and fuel, and should be replaced when it leaves a clear mark on the clamp. It is still convenient, although there are few opportunities for immediate delivery at Webig due to the spec. on the order. View detail
Classic look, I think the quality is good
Installed on Yamaha SR500.
Fuel Cock before replacement (Manufacturer unknown Other Brand Product) worked hard for about 15 years, but when I rode it for a while, it started leaking.
This time, we chose this Fuel Cock, which is handled by DAYTONA and has high reliability.
The look is classic, the lever operation is very light, and the installation was fairly normal.
I can recommend it
View detail
สวย ใช้งานได้จริง ตรงรุ่น View detail
I appreciate the ReserveCook.
There is no Reserve in RigidMONKEY or 4LMONKEY's Normal cook.
In the past, I had to go to the trouble of replacing the cook's mounting part with M14 to install a cook with reserve, but this cook can be installed as is, which is a big help.
Especially in the case of 4L, the normal cook is downstream, so if the carburetor is PC20 etc., it will interfere with the cook.
However, this Cook is a Right out, so I'm going to make that point. [Color] You can Clear.
I don't have any problems with installation or usability, but I don't like the fact that Packing is so poor.
Gasoline may leak if it is tightened a little too much.
Nevertheless, I appreciate ReserveCook.
View detail
MONKEYCarburetor/Drain hose
[How is it used? Overhaul of MONKEYCarburetor, repair of oil leak, replacement of hardened and cracked tube due to deterioration.
Was the one you received as per Image?
It is soft, durable and looks much the same as OEM.
Was the installation difficult?
Just cut them to length.
How was your experience with it?
It was soft, easy to use, and easy to install.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
As expected.
Point of installation and hang/.
Each hose of MONKEYCarburetor has a different size. the part of Drain that drains oil has a size of 3.5×7.5.
View detail
Hose connecting MONKEYCarburetor and Tank
I thought the cause of the oil leak was packing, but the hose connecting the tank to the carburetor also had a little tear due to deterioration. I was not able to find an OEM hose, so I purchased this product.
The Sizes of other Hose in Carburetor are different from each other in size at each location.
Hose connecting Tank and Carburetor was this product (4.5×8.5).
The quality is good, durable, soft and problem-free.
View detail
It is a good item
No fuel leaks and very pleasant, it is painted in color and has a nice texture. View detail
Fuel fliter
I bought this because I frequently get Garbage in my carburetor and it clogs up frequently! 。
The installation was easy and the filtration was good.
View detail
Fits: KAWASAKI 500SS Mach III (H1), KAWASAKI 750SS Mach IV (H2), KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000, KAWASAKI Z2 (750RS), KAWASAKI Z750, KAWASAKI Z900 (KZ900), KAWASAKI 500SS Mach III (H1), KAWASAKI 750SS Mach IV (H2), KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000, KAWASAKI Z2 (750RS), KAWASAKI Z750, KAWASAKI Z900 (KZ900)
Used for Z750four
I purchased this to change the location of the Overflow hose that was previously attached.
I had previously purchased and installed a PMC one, but it seemed somewhat thin and meager in comparison.
There are no problems with installation or use.
The price is low, so this is sufficient for those who only need it for the time being.
The look and texture was not great.
I thought PMC's would be next.
View detail
As a carburetor for RepairHose
The carburetor hose was ruined, so I purchased this product to replace it.
The vehicle model is Husqvarna 2016 TE250.
Hose with an inner diameter of 4φ×outer diameter of 7φ and a length of 1m.
Clip×Quantity:2pc. I am glad that it comes with Set.
It is not long enough to replace all of the hoses used on off-road motorcycle carburetors.
In this case, you need to check in advance how many meters you need and look for longer products or buy several of them.
View detail
As Repair Parts
Since it is an OEM shape, Cook's Packing is deteriorating, so I'll give it a try! View detail
Fits: HONDA CB400SF, HONDA CB750FC, HONDA CB900F, HONDA CBR250, HONDA CBR250, HONDA CBR250, HONDA CBX1000, HONDA MVX250, HONDA VT250F, HONDA VT250F, HONDA VT250Z, HONDA VT250Z, HONDA STEED400, HONDA VF400F, HONDA NSR250R, HONDA NSR250R, HONDA NS400R
Savior!
VT250F (F2F) was leaking fuel from the cook, but the OEM parts were Assembly and not in stock …
I had no choice but to break the Crimp with a drill and turn the Packing inside out, but it still leaked, so I searched and found this part!
I bought it right away, installed it, and it matches perfectly!
I found it so good that I am thinking of buying another one as a spare.
Thanks!
View detail