Reviews
Mk2 with tmr36 and PinGel6000
I installed a tmr36 on a mk2, and the OEM cook completely interfered with the installation, but with a 6mmOffset PinGel6000 mounted slightly to the rear, I was able to complete the installation without any problems. View detail
Super fuel hose set 991-0311000
Used for Carburetor lower overflow hose.
This is the case in the Parts List. (mk? was it?) I thought the inner diameter was 3.5mm, but the alternatives from Company P and Company D were also 3mm, and KITACO did not have half as many, so I bought 3mm. KITACO also did not have a half-decent number, so I bought the 3.5mm. I bought a 3.5mm diameter pipe because it is soft and easy to use.
I liked the Pink color, although the slightly firmer Green would be better for Flow Hose.
When I tried to replace it, I discovered the problem:1m is Quantity.:I can only take 2pcs.
Plans to reorder. I'll have to write another tiresome impresario. I have no time to be poor.
Should we try a Pink/Green two-tone color at this point?
View detail
Clear hose 105-075
Used for Breather Hose 650mm 6mm Diameter for open battery.
Is the name right? It's the Hose that's down from the side, pulling out the Gas.
My Z needs a long length to hang down to the bottom of the exhaust system. (There is also a turn along Tire house) The hose that comes with the Battery is not enough at all.
The price was almost the same as the material store, which is good.
The construction is fine, thick-walled and thicker (8" OD), so it was difficult to pass through in some places, but no problem. It is better than the cheap ones.
Incidentally, I tried an inexpensive Silicon tube once before and the entrance side fell apart in less than a year.
View detail
Cospar good
It is practical because you will not notice the Rust in the Tank going into the carburetor. View detail
ใช้งานดี ดูมีสไตล์ แล้วจาสั่งอีก View detail
Dress-up
There are many effects, but OEMCook...
For dress-up because of yabo
Installed. It looks very
Well-organized and satisfactory, but perish Brown bitter Brown
WhiteRust is easy to find.
View detail
May be easy to loosen.
I bought it because it is a Pressure Resistant, Oil Resistant Hose.
Leather mesh inevitably tends to unravel at the edges.
Well, that is acceptable.
The problem is that the inside Hose might be easy to loosen.
I used Oil Resistant Hose from KIJIMA or DAYTONA without Clamp and it never came loose.
I wonder if that is Minus.
View detail
For Sub tanks
I bought this because of the possibility of contamination of garbage when using a Sub tank without any Filter.
I have no complaints, but I found it a little confusing that there is no description of the direction of the Filter.
View detail
Essentials for old cars
Aluminum is a good material because it is resistant to heat and cracking, lightweight, compact, unobtrusive, and does not get in the way. The aluminum tanks are heat and crack resistant, lightweight, compact, unobtrusive, and unobtrusive, and they also free the carburetor from frequent clogging, which makes for a refreshing feeling of relief. View detail
Oil hose replacement
Oil hose cracked and replaced. View detail
Fuel Hose
CRM's Fuel Hose was cracked and was replaced. View detail
Required for PinGel
When changing to PinGelCook, be sure to
You will need it. Quality is quintessential, no complaints.
But PinGel is also moderately priced.
The price is a little hesitant to purchase this one at the same time.
View detail
Fits: HONDA APE 100, HONDA APE 50, HONDA MONKEY, HONDA MONKEY, HONDA APE 100, HONDA BENLY50CD90, HONDA BENLY90 S, HONDA GORILLA, HONDA GORILLA, HONDA CUB-based Engine CL, HONDA CUB Engine CD
tl50 isn't in the fit, but it's perfect!
I thought, "tl50 is not compatible, but it's a Honda, so if the screw diameter is right, it will fit! I half gambled and bought it!
The diameter of the Fuel Cock section of the tl50 is 14mm.
This is the same APE Tank I used to tinker with, so I knew it would probably get there!
If you measure the screw diameter with Caliper, I bet you can use it for the most part.
Motorcycles over 40 years old are amazing! The packing of the Fuel Cock is so chica like plastic and not even half of it is left!
Good thing Packing was planning to change everything.
I'm afraid of Gasoline leakage if I run like this.
It can't be!
Comparison with OEM
OEM is easy to understand because On, Off, and Reserve are written in letters.
I know this item, Off, because only one notation (circled) is different!
But On, is Reserve a pictorial notation? Pictographs?
I don't know what to look for in such a Д゚ Mark…
You have to remember intuitively where the cook twists!
The plastic tube like a filter is attached to the top of the Fuel Cock. However, when I installed it on my tl50, it would not fit in the tank with this Filter attached, so I had to pull the Filter out and leave the tube inside!
View detail
KIJIMAFuel Filter
I tried installing a cheap Filter before.
I purchased KIJIMA's Filter, which looks great this time!
It's a Glass type that allows you to see inside well and clean it, so it's a commendation!
View detail
Since it interferes with
I used to use a fuel cock from company T, but it didn't last six months and leaked even when the cook was turned off, so I decided to buy a KITACO fuel cock.
If it leaks in a short period of time, buy OEM like Large people.
The cook outlet can be selected to be forwarded, which is nice because it eliminates interference even if a big carburetor is installed.
View detail
สิ้นค้าดี มีคุณภาพ ส่งไว View detail
To old Motorcycle because the inside of the Tank is also old.
It's good for Carburetor Vehicles because you can see the Gasoline movement. View detail
Very well.
Nothing to say about the fuel tap of the kawasaki 750 zephyr. Perfectly replaces the original gauge without any unpleasant surprises. -------------------------------------------------- -------- Nothing to complain about the gas tap of the Kawasaki 750 Zephyr. Perfectly replaces the original gauge without any unpleasant surprises. Powered by Google Translator View detail
Satisfied
Good cost with 3 different sizes View detail
Looks like they're improving. (^^) Used for 4lInitial Model
I didn't like the Cook on the bottom out and ended up here.
First. RES-OFF-ON." is strange! I have heard that the display of "☆" is strange, but it seems to have been improved, and the one I purchased had the characters in the display. The image is also before the replacement.
I had no problem installing and using it. The switching operation is also well done, and I personally do not feel that it is cheap, etc.
Incidentally, I did a rose before installation, and the internal packing is also in line with the OEM, so I am not worried about the after installation.
I was curious.
There is a BALI at the Cock outlet and the inside diameter is narrow. The intake port at the time of ON is narrow and it seems to be hard for fuel to fall out. The mesh part of the Strainer is high, so fuel may remain.
Right. Well, as far as the others' are concerned, I guess there is no problem….
View detail