Reviews
Fits: HONDA MONKEY, HONDA CUB, HONDA DAX, HONDA GORILLA
CoreBody is available.
This is my second purchase. The first one I purchased has no problem except for the Mesh hose that came with it, which I replaced with a commercially available Hose because the finish of the Mesh hose was not good and it was cumbersome to handle.
The thing which was purchased this time tightens Screw of Side cover by hand first, but I felt something caught, but I tried to assemble it for the time being. It is not possible to tighten and loosen. After a while, I tried to tighten the screw because the oil leaked from the side cover, but it was useless. Compared to the OEM side cover, the screw holes are slightly off and the whole thing is distorted, so I had to buy the side cover again. After all, the CoreBody and Bracket are the only ones I can use. It's a shame because the first one I bought is working fine. However, it is still cheaper than the manufacturer's products so you can use it even if it takes some time and effort.
The Engine is CUB series 110cc.
View detail
Fits: HONDA MONKEY, HONDA CUB, HONDA DAX, HONDA GORILLA
Cheap and bastard
Bad point one.
Instruction Manual is not enclosed. Because it is only an oil cooler, it becomes manageable even if it is not used to it.
Bad point 2.
The oil cooler mountings are welded upside down, or the female screws may have The Bolt didn't go in because it was not chopped.
Others
We are still breaking it in, so we haven't run it at full throttle and its performance is unknown.
View detail
Fits: HONDA MONKEY(except FI)etc.Horizontal TypeEngine, HONDA MONKEYetc.Horizontal TypeEngineUniversal
It's well worth the price, but it does require some processing
Hose is hard It's better to get a separate hose
In the case of the BearingCam, it is necessary to scrape off the protruding parts of the ejector If you use it as it is, it is almost certain to leak oil, so you need to prepare a liquid gasket separately It is safe to reassemble the Nipple and then install it
Bottom line, Core was perfectly fine
It can be fixed with a 50mm U-shaped long bolt It's a non-interference, so it's Recommendation
We finally switched to taking out another company..
View detail
Fits: HONDA MONKEY(except FI)etc.Horizontal TypeEngine, HONDA MONKEYetc.Horizontal TypeEngineUniversal
We recommend to consider other company Oil cooler
Current situation, I can not do until installation, but in bullets
? Screw preparation is necessary separately for installation.
From the finish of the appearance, I thought that it disgusted
? Long Screw fixing the fins is Rust.
? There is a trace in Pipe of Oil line and it is dirty.
? There was a dent that the Pipe of Oil line was forcibly pushed in, there was a dent.
? Packing of O-ring is used in all five places, nine are used, but all are damaged. It is torn or is deteriorating.
From the above, it is absolutely a product that can not be Recommendation to other people.
If you consider Overhaul (Although it may be an implicit consent) If it is, I will think that I need a note.
View detail
Fits: HONDA MONKEY(except FI)etc.Horizontal TypeEngine, HONDA MONKEYetc.Horizontal TypeEngineUniversal
It looks nice.
Oil seal and hexagon socket M6 length 2 cm long Screw required
Also, since Nut stopping Camshaft Chain Cover was about 3 mm long, I put Aluminum 5 mm Washer and adjusted it. Perhaps Oil will leak if it is not Aluminum.
Instead of Oil seal.
View detail
Fits: HONDA MONKEY(except FI)etc.Horizontal TypeEngine, HONDA MONKEYetc.Horizontal TypeEngineUniversal
It is a bad product as the product arrives and surprises it.
First of all Core is in a state of serious condition.
Once checking the flow of Oil flow is too bad - - - Even if I put in the air, I feel that there is a sense of resistance and it becomes considerably resistant at the viscosity Oil.
In use with high rotation Engine there may be a possibility that the circumference of Oil is bad and it will be stuck.
View detail
Fits: HONDA CHALY 70, HONDA ST90 (ST90), Others , HONDA DAX70, HONDA GORILLA, HONDA CHALY 50, HONDA DAX, HONDA MONKEY
Regret goods
Because I am using Engine tune I use Oil cooler throughout the year, but this time I bought it as a supplementary purpose of MainOil cooler by midsummer Overheat countermeasure.
First of all, since there was no Screw hole for installation, there was no Clearance to establish a Screw hole, so we purchased Bracket for a water pipe at Homsen and installed it somehow.
I also wanted to replace Nipple with another one, but the Screw hole was 12 mm 1. Nipple selling for 25Pitch can not be used and there is no pain in Universal's freedom.
Design and fabrication are beautifully satisfied.
Because it uses it as a sub Oil cooler, the cooling effect is as expected.
View detail