Reviews
Fits: HONDA BENLY50CD90, KAWASAKI D-TRACKER125, KAWASAKI KSR110, KAWASAKI KLX125, KAWASAKI KLX110, SUZUKI ADDRESSV125, HONDA CBR250R, HONDA DREAM50, HONDA DAX, Others , HONDA MONKEY, HONDA GORILLA, HONDA CRF50F, HONDA MAGNA50, HONDA Ape50, HONDA Ape100, HONDA XR50R, HONDA XR50 Motard, HONDA XR100 Motard
Great option
This product is a great idea to warm your engine oil up properly! I was super happy with it and felt the bike warmed up alot quicker to operating temperature, easy to fit and install View detail
Made the oil cooler lines look really tidy
I was super happy to see this product arrived, it kept the oil lines from hitting the exhaust and also made them look very orginised as it was super easy to install View detail
Installation is a challenge, but it looks good!
I found this product because my OEM side scoop had rust floating on the steel and matte black paint, even though I wash it frequently.
VMAX1700 itself is not very easy to maintain, so replacing the Parts around the Frame inevitably involves removing the Seat and DummyTank Cover, which is a kind of ritual that must be gone through.
I had searched the Net for blogs of people who had installed the same products in advance, so I went to a nearby YSP to find double-sided tape and CS wheel stops that I would not be able to reuse when I removed the product.:Pair (for Left and Right) Quantity for Duct cover of:2 Sets of OEM Parts are ordered and purchased.
Work Start on the day when everything is in place!
Seat, which is a ritual, Tank Cover removed and Side cover is Quantity.:Pair (for Left and Right) When removing the third bolt, be careful not to drop the bolt and damage it!
I tried to remove the U-shaped pin with a slotted screwdriver, and then I tried to remove the CS ring stopper with a slotted screwdriver, but it did not come off very well, so I used a backdoor technique and folded the reverse side of the mesh over at the projections through the three rectangular holes. I fixed it straight with Driver and RadioBench and pushed it from the reverse side with Driverretc. and only the net part came off from the front side.
All that remains is to position the product from the front side, peel off the double-sided tape portion, and affix it.
I found this to be by far the most efficient way to reduce the time and hassle of removal, so although it is different from the Manual, I had no particular problem with it.
I think the appearance is to your liking. While the overall silver color differentiates it from NORMAL, the two-tone color with black also tightens up the look, so it is hard to say that OEM parts are not good.
However, the material is Stainless Steel, which is by far the most rust-resistant. I don't think the English letter engraving is necessary.
It is a cosy way to change the look and feel of the product at this price.
View detail
Fits: KAWASAKI Ninja250, KAWASAKI Ninja400, KAWASAKI Z250, KAWASAKI Z400, KAWASAKI Eliminator400
It is still first class!
It is still first class!
Cool！
Installation is a simple push-on with the included clip bolt. (*´?`*)
This time I installed it on my wife's ELIMINATOR 400, but now I think I'll change my Z9 to it too.
View detail
Looks nice
I got this item to secure the hoses from the cooler to the engine and it was easy to install and looks really nice and keps the oil lines looking tidy. Great product View detail
Fits: HONDA GORILLA, HONDA MONKEY BAJA, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY BAJA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
Looked amazing
These fitted really easy and had no problems fitting them to the motorbike. i was really happy wth how they fitted and they made the bike look really good. The cooler worked really well on my engine and kept the engine oil coller meaning less wear on the engine which i was very happy with View detail
Required for Crank Case Cover
Hose holder is attached to Crankcase and is required when replacing KOSOCrank Case Cover. The other attachments are all gold and the same color, so 5 stars. View detail
I think it is a high quality product.
Radiator core guard is necessary because it not only protects the radiator core from dust and stones, but also makes it difficult to see mud splashes by wiping it off.
I have purchased some Reasonable overseas products, but the quality was not commensurate with the price, and even after installation, I was concerned about the fixation method.
The Etching factory's products are of high quality and the fixing method is well thought out, so I was glad to have them because they are safe and look luxurious and satisfying.
View detail
I'm very happy with it
Installation was very easy, took only 5 minutes. It looks simple, but I think it works well. There were other products available with finer grain, but I bought the OEM version and installed it myself. There is a little space at the four corners, but considering that it does not interfere with the air cooling effect, I think it is sufficient. View detail
Casually Parenthesis better.
You will be satisfied with the results you get.
Care must be taken with the Radiator Cap during installation.
Depending on the type and orientation, there may be interference. Push rivet was used to attach the front cowl. To avoid contact wear, a thin rubber plate was inserted as a cushioning material.
View detail
To replace a deteriorated and obsolete Radiator hose
This is a combination of Straight Type hose and Hose Joint Pipe and is used as a substitute for the Radiator hose, which has been discontinued and cannot be replaced.
The coolant was nearly 40 years old and had deteriorated to the point of leaking, but we were able to stop the leak by replacing it.
Although it was not possible to make it the same shape as the NORMAL, both the inlet & outlet could be made in the same position as the NORMAL, and the substitute could be made without putting a load on the hose.
View detail
Tools are required
The most difficult part is to remove the bracket from the throttle body. Once this is removed, installation is easy, Even if you have an oil temperature meter, it will not cool down without an oil cooler in summer. View detail
Polisport Radiator Shroud Set for CR125R 2001
This was a set of radiator shrouds that needed replacing for wome new ones as the old ones had a lot of damage from rocks etc. I decided on the Polisport ones as I have used them a few times before and have had good experience with this brand. The radiator shrouds were pretty good value and are cheaper than some of the other alternatives out there. With a few other parts in my order, all were shipped together to save some costs. My order was delivered by EMS and took 5 days to arrive. The shrouds arrived in the Polisport packaging and were surrounded in buibble wrap to keepo them from sustaining damage in transit. The shrouds are made from a strong plastic material and are pretty robust and strong. There is a bit of flexibility so you can sit them fairly easily. I would recommend this brand for off road bike body work as they are cheap enough and last a while. The quality is really good and I found no flaws at all. Very pleased after fitting and the bike looks a lot more appealing now. Thanks Webike. View detail
Large Satisfied
Since the oil cooler for Harley-Davidson does not have a horizontal type mount type, we fabricated a mounting bracket and installed this oil cooler. The oil cooler was installed on the front frame in front of the engine through the aforementioned bracket so as not to interfere with the front fork and not to obstruct the foot space. It was installed quite nicely. View detail
Fits: HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS
Parenthesis is a uniquely chic design!
[How is it used?
In addition to MORIWAKI, YOSHIMURA, K−FACTORY, Etching factory, AGRAS, and other companies have released oil cooler core guards, but we chose this black one to match the MORIWAKI muffler.
Was the one you received as per Image?
Black shines duller than Image and has a gun metallic look to it, Parenthesis is great!
Was the installation difficult?
It may be a little tricky at first, but it is relatively easy to install after removing the rubber bushing on the oil cooler side.
How was your experience with it?
At a quick glance, it looks NORMAL and unobtrusive, but if you look closely, you can see MORIWAKI, which is a good example of casual customization.
[Included Parts:were they on?
In addition to the Instruction Manual, a complete set of washers, screws, etc. are also available.:Set
Also included is a MORIWAKISticker.
[Was there anything that disappointed you?
The price point is a little high, making it difficult to afford.
Even the screws and ribs are painted black, making it a very special item. It is a perfect part without any complaints because of its high price.
View detail
fast delivery, nice quality
It allows you to know the temperature of the engine oil indirectly There are variations in accuracy But it goes well with the bike and is pretty View detail
To repair engine oil leak
Already "Old car" I have a Live Dio (clog scooter) that is running fine, but it is leaking oil, which is a promise of 2CycleMotorcycle, … In such a case, this product can repair the OilLevelSensor without replacing it with a new one! It is a recommendation! View detail
Fits: KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS Yellow Ball Edition
Large Satisfied
The product is better than expected, no Speed complaints. View detail
Just fit like OEM Product
I purchased again this time.
It is mechanical and looks great on the air-cooled CB1100. It is not accurate, but it allows you to check the degree of oil temperature rise and has the effect of preventing overheat in the summer,
View detail
Replacement from OEM Product
I replaced the OEMCap that was too assertive for my Black vehicle with this one. It is not a compatible car model, but … I was able to install it without any problems.
I haven't driven the car since it was installed, but I'm happy to say that it looks exactly how I expected it to look with the uniformity of the Black color.
View detail