Reviews
Fits: HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300 SUPER BOLDOR, HONDA CB1300 SUPER BOLDOR
K-factory radiator core guard
Now if there is a difference in width size of the radiators I had to re-drill the holes on the side brackets by about 5mm each side then the cover slotted over nice and tight so expect there could be some adjustment needed View detail
Hyper Bulb
Installation was quite simple View detail
The HorseMaterial is hard.
Material the Tank of WR:When I replaced it with IMS to make it plastic, the Hose on the end of the Cap was too plain, so I bought this one. However, the material of the hose was too hard and came off easily, which was caused by the fact that the cap did not have a shape to prevent it from coming off. I should have used Aron Alpha. View detail
Feeling flow instability as per other impressions.
I use it because I often Overflow on my old car.
I'm not particularly particular about the Manufacturer, but DAYTONA seems to be well worth the price. There are no visible defects, such as paper wrinkling.
However, as mentioned in other impressions, the flow rate seems to be lower than other companies' products, and sometimes the Gasoline would run out at full throttle on the freeway scene, etc. (Waiting a bit will fix it.) Also, the Gasoline would suddenly stop running due to air bite, although the cause was unknown (I'm not sure if this was due to the Direct product, but removing the filter would fix it). (I don't know if this was due to the Direct product, but it was fixed by removing the filter.)
Therefore, it is not very useful for 250ccSports type motorbike.
I will look for a product with a higher flow rate.
View detail
Power Filter
I replaced it, but could not get a sense of the experience. View detail
No durability
The quality of Rubber is poor and cracks immediately after 6 months. View detail
The magnet is missing.
Installed in vehicles without an oil filter. It collects impurities with a mesh filter and magnet.
The inlet and the net filter are too close to each other, and if dirt accumulates, it will clog the filter.
The magnet is shaved and the quality is delicate.
Plating on the reverse side of the case is defective and the quality is delicate.
Well, better to have it than not to have it.
View detail
I think Dress-up is the main one.
[How is it used?
I installed it on a vehicle that I normally use for Race.
Was the one you received as per Image?
Yes.
Was the installation difficult?
It is easy to replace the original screws by simply loosening them with a screwdriver.
How was your experience with it?
I was told that I could turn it by hand, but with my vehicle, the hose was in the way and hard to reach&I couldn't turn it by hand.
[Included Parts:were they on?
There is none
[Was there anything that disappointed you?
Cannot be turned by hand.
It may be a good idea to purchase them as dress-up parts, but you may not want to replace them for practicality.
View detail
Pricey OEMParts
I bought this product because it was the company's Bore Up Kit and there was an entry in the description that said it should be replaced.
When I received the package, I found that it was just YamahaOEMParts in the KN project Package.
The things are OEMParts, no doubt, but it is cheaper to buy OEM as-is, and since OEMParts are available at Webike, we do not recommend buying this one.
View detail
Cylinder replacement
I took down the head of the MONKEY to replace the valve, and when I removed the head and checked the cylinder, I found it was damaged. It would be very helpful if I could buy the parts I want at Rose, but the quantity is very limited.:It is not cosmetic as it is a Set purchase. I hope it will be improved. Also, it is R-STARGE+D Squat106, so it is quite fast, but the MaintenanceCycle is short! (Maybe it's just mine?) View detail
Fits: SUZUKI GSX1300R HAYABUSA, SUZUKI GSX-R750, SUZUKI GSX-R600, SUZUKI GSX-R250R, SUZUKI GSX-R1100W, SUZUKI GSX-R1000, SUZUKI GSR600, SUZUKI DR250R, SUZUKI DR-Z250, MALAGUTI MADISON400, PIAGGIO LIBERTY-50, KAWASAKI BALIUSII, KAWASAKI BALIUS, KAWASAKI ZEPHYR400 χ, KAWASAKI ZEPHYR1100 RS, KAWASAKI ZEPHYR1100, KAWASAKI ELIMINATOR 250V, KAWASAKI ZZ-R400, KAWASAKI ZZ-R600, KAWASAKI ZZ-R1200
I'm not sure what the difference is.
I have been using Iridium plugs.
I did not feel any difference in my experience when I switched to this Plug.
I will use it for about 10,000 km since it seems to be sold as "long life".
View detail
Fits: Others CR-mini Carburetor, Others PECarburetor, Others PWK Carburetor
The price
Aside from the hole Sizeetc., the overall construction (finish) is clunky compared to KEIHINOEM and POSH's Jet.
Well, I guess that means it is in line with the price. Well, it does its job as a component, so it's fine.
View detail
PWK Type" For?
I was looking for replacement parts for a carburetor that was not leaking gasoline and I thought it might be overflow, and I found this one. I bought it because I thought it would probably be useful.
Float Gasket and other packings can be used.
Float also has a different shape, but I think it is Large sturdy.
The kit includes a Needle and Needle Holder, but the Needle Holder is different in size and cannot be installed. The difference in the diameter of the bleed holes can be seen when they are placed side by side. I can't install it, but even if I could, I am afraid to use it. I was swearing to myself that I should put this on even without ChalkBoots.
Buyers should check their own PWK's Size before making a purchase to avoid disappointment. Please be careful.
The Gasoline leak was not fixed, although it was attached where it could be attached. We are continuing with the repair work because we were able to eliminate one of the negatives for the time being.
View detail
Broken and replaced
Sensor broke, so I had to replace it. It didn't last long because of a bad hit. View detail
Fits: Others Universal
Broke after 3 months.
AF05E with AF35carburetor installed
Cover part is Material:Plastic, and I noticed that the Bolt was cracked from where it was stuck.
Fortunately, even if this part breaks, it is sucked in via Filter, so we have no choice but to use it as a normal Powerful!
View detail
Fits: その他 (For TMR carburetor)
Used for BST36
I used it on a BST36 and it was a little too long.
It's for TMR, so maybe it's just fine there.
View detail
The netting is too soft and difficult to replace.
The netting is soft, so when the bolt is tightened, it flattens and is not parallel to the bolt. View detail
It's disappointing.
It came in a color not in the picture. I wanted a gold color, but it was orange. Metal is weak. One is the wrong length.It came in a color not in the picture. I wanted a gold color, but it was orange. Metal is weak. One is the wrong length.It came in a color not in the picture. I wanted a gold color, but it was orange. Metal is weak. One is the wrong length. View detail
Fits: YAMAHA DRAGSTAR400, YAMAHA DRAGSTAR400 CLASSIC
A bit of a shame …
The bolt length in the Instruction Manual was different by 5mm from the bolt that came with the product, and could not be installed.
It was a hassle to return or ship it back, so I bought Bolt again at Homsen,
Other than that, it was good, so 2 stars.
View detail
Fits: HONDA PCX HYBRID, HONDA PCX, HONDA PCX150
Purchased based on appearance alone.
Purchased based on appearance alone.
Difficult to turn, Level gauge is hard to see
I think the quality must be good.
If you're willing to drop a little quality for a cheaper
View detail