Reviews
It is not usable as it is.
I replaced my mc22 94 with this one because it wouldn't stop leaking.
The replacement itself was easy.
However, liquid is leaking from the Drain section.
I thought this might be the case, so I removed the drain bolt and found a seal washer on top of the black paint, as well as a groove on the bolt for a crimp. It was no wonder the bolt was leaking.
The paint was removed with sandpaper and the Bolt and Washer replaced with OEM.
The leak has stopped.
The product itself is solid. But it needs a little work.
View detail
Helmet In Box needed to be modified.
Product Description With this kit, you can replace the carburetor without the need to modify the Helmet In Box or Cowl." but when the PWKcarburetor was attached, it made contact with the Choke Knob faction.
When the rear suspension sinks, the carburetor almost comes off as it is.
Helmet inBOX processing and Choke Knob processing were used to overcome the problem.
I'm a little disappointed and will be replacing it with Wire-style Chalk.
I don't know if I installed it the wrong way or not... (It only sticks as it sticks!)
View detail
Fits: YAMAHA CELLOW 250, YAMAHA Tricker 250, YAMAHA CELLOW 250, YAMAHA Tricker 250
Refresh OEM Product Replacement.
I bought this one because the OEM is discontinued, and it is an OEM Equivalent Product, which is fine, but the O-ring is not included.
The cylinder head was replaced while removing the cylinder head.
The OEM Product we removed had cracks but no secondary air contamination, so the functionality remains the same, but the new Rubber feels good. Durability remains to be seen.
Cautions for installation
The bolt attached to the engine was sticking, so I had to spray it with penetrating lubricant and leave it for a while before I could remove it.
View detail
For anti-seizing.
It was used to refresh the cooling area of MAJESTY125 for bore up.
I am still afraid of burning out as the weather gets warmer in the coming months, so I decided to purchase the WaterLine because I thought it would be a good idea to review it as well.
It is inexpensive, but the product is well made and can be used without any problems.
The body already has 60,000 km on it, so I believe it works much better.
View detail
It's a great cosmetic
Used to Refresh MAJESTY 125.
We chose the Bore Up Kit because we wanted to do something about the inefficient acceleration if we were going to do it anyway.
It is much cheaper than OEM Type Cylinder, but the quality and precision are perfect.
Since there is no instruction manual included, I think it will be quite tough if you do not have the skills to make your own motorcycle loose to some extent.
It seems that the 160cc engine finally has the acceleration power that is commensurate with the large size of the body.
I think it will be much easier to overtake, start at a traffic light, and start at Tandem.
View detail
Fits: YAMAHA XJ650, YAMAHA XJ750, YAMAHA XJ650, YAMAHA XJ750
A-Top Carburetor Joint XJ650
It cannot be installed because it is facing the wrong way. View detail
![Cylinder Kit [for Repair]](https://img.webike-cdn.net/catalogue/images/59617/7_000000001910_TS.jpg)
It looks good quality.
The Engine of CB125T is being overhauled.
The engine was purchased used, but the inside of the engine was covered with sludge and was completely brown, probably due to poor oil management.
This is a Level that is coated with something from Brown's.
Fortunately, the condition of the Cylinder and Piston was better, but out of curiosity, I bought a Cylinder kit from ATOP.
Since we are working on a 125cc to make a Hen LeverMachine, we dared to use Replacement for OEM. instead of Bore Up Kit.
I was a little worried when I saw the Bore Up Kit made by Large Land for CUB-type engines, etc., but it seems to have a brand name, at least.
There was a Laser engraving of ATOP on the LeftIntake side of the CylinderTop.
The paint is a darker Silver.
It will be a little while before I can use it, as it is taking a long time to rosette due to various sticking points below the waist, but I think it is better than using an OEM with an unknown history of use.
I would like to Review it again when I put it together.
Naturally, there is no Instruction Manual for handling or assembly, so if you do not know what you are looking for, please refer to Honda's Service Manual or Parts List.
View detail
No problem
I used it on the Engine of my CB125T which I am using as a RoseRose.
All the main Gaskets are included. What was unexpected, in a good way, was that the rubber packing for the head cover was also included.
It was very helpful because if I had taken it off, I would have been rattled.
When I bought a Cylinder kit at the same time, it also came with a Head Gasket, but it is not expensive, so it is good.
This Engine seems to be copied a lot on Large land, so it would be nice to have a Knock Pin Set or something.
View detail
Fits: SUZUKI GN125, SUZUKI GS125, SUZUKI GN125H
A defective product?
After breaking in, the engine was disassembled again and the valve hit the upper part of the piston, causing the EX valve to deform. I think it is a defect due to the forced structure and the position of the shaved part of the Piston that dodges the Valve is gapped, so it is better not to buy it. View detail
Gasket and oil seal are included in the price.
Since the OEM Clutch Cover Gasket is about 2100 yen, this price is a good price for the Gear case Gasket and Oil seal included.
However, compared to OEM Gasket, the cut edges are rough and BALI is more common, so the quality of the appearance is clearly lower.
I haven't used it yet because I bought it as a spare after using the OEM I had on hand, but it would be nice to have one Stock.
The Gasket on the neck has not been used yet, but it will go to the warehouse until the time comes to maintain it someday.
View detail
For advanced players! Bowling/Honing Additional Work Required! High-octane Spec.
I purchased this for my JA10 light motorcycle registration.
As a conclusion, the Bore Up Kit cannot be used as a stand-alone unit, and additional work for bowling and honing is required.
The clearance between the Piston and Cylinder is very narrow and will cause the Engine to blow if assembled as is, such as if the Piston gets stuck.
As a countermeasure, take this Bore Up Kit to an internal combustion engine shop for additional work to achieve the proper Clearance, which will be immediately apparent when this product arrives in your possession.
Although not mentioned in the product description, the Bore Up Kit increases the compression ratio to approximately 12.1:1, making high-octane gasoline a must for sure.
The problem is that I am a little concerned about whether the engine of JA10, which is famous for its failure, will be able to withstand such a high compression ratio.
Also, the ValveHit on IN and EX, which was a concern, did not occur.
So far it is working fine, but it is still in the break-in stage, so I would like to review it again somewhere after some driving.
View detail
It doesn't fit except for Packing.
I bought these for my 98 2WE Carburetor overhaul, and the sizes of the Needle Jet, Jet needle, and Main jet etc. were completely different. I was expecting the quality of the product since it was made by Webig, but the size was completely different from the original size.
If the Size is right, I think the cosmetics are great. The return policy was very good, the price is low, and there is a wide variety of products, so I will use your service again.
View detail
Fits: HONDA Rebel 250, HONDA Rebel300, HONDA Rebel300
a little too short
It was too short and when installed, the carburetor and air duct could not reach the Air filterBox. It could not be used. View detail
replacement head gasket
I received the full set but only the head gasket was dented. I have write in and Webike was so kind that help me to replcae the dented piece. Many thanks Webike team. View detail
OEM Equivalent Product.
Used on a MAJESTY 125 Restore purchased for $30,000.
It is undeniably just an OEMcarburetor.
but the original carburetor was in pretty bad shape and improved dramatically after replacement.
However, since Motorcycle is an OEM and has quite a few pre-existing conditions, I would not have hesitated to buy a CVK30 or KOSO KVR instead of buying this.
As a postscript, Gasoline started leaking around the acceleration pump while in use early on, so the quality seems to be adequate, even though it is still the same etc. as OEM,
View detail
Fits: HONDA CBR250RRR, HONDA Hornet 250, HONDA CBR250R, HONDA Jade 250
Seal used for water pump removal
A little thin, but no problem when used with liquid SealPacking View detail
Some of the items are in the picture but not included.
I am a little disappointed that the Screw, O-ring, and Needle Clipetc. shown in the picture were not included, although it is nothing to be concerned about since they are not Large. View detail
I got out of Setting with ease.
Vehicle used HondaNS1 first half 68.8Bore up vehicle
I bought this carburetor after having a hard time finding a Setting with the PE24 Carburetor. I got the best Setting that day.
I think there is a difference in each vehicle, but Slow Jet 52, Main Jet 110, JetScrew is at the smallest aperture close to OFF, and Jet needlePin position is in the middle. I was satisfied with this setting because I was not looking for such a high speed, but the limit value of 100 km/h was reached on a flat straight line where there is no restriction by law. In addition, the external material for PWK:AluminumIdle Screws and Air Screws are available in Quantity:It is possible to set, but it would be better not to do so. The external Idle Screw was clogged with gold fragments due to rubbing, and the external Air Screw had no O-ring and the adjustment screw was in the wrong position, making adjustment unstable due to 2-dimensional air intake. As a result, the needle included from the beginning is the best and most stable rather than focusing on appearance. [Color] The ClearFloat chamber is Standard Equipment and the oil level is clearly visible. Overall, I would rate this carburetor as a well-made carburetor that is easy to handle for the price.
View detail
THE carb kit
An incredible value for money and really complete, everything is there. Even the O-rings for the tees between the carburettor bodies are provided. The membranes of the bushels are changed without problem which avoids having to buy them complete. -------------------------------------------------- -------- An incredible and really complete value for money, all is there. Even the toric seals of the tees between the carburetor bodies are provided. The membranes of the bushels change without problem which avoids having to buy them complete. Powered by Google Translator View detail
MC19CarburetorOHKit
I bought my MC19 used, so I don't have the same feeling as when I bought it new, but I think it's probably back to normal because the Idling is stable and it blows up well. View detail