Reviews
Fits: HONDA CB1100, HONDA CB1300SF, HONDA CB1300 SUPER BOLDOR, HONDA CB1300SF, HONDA X-4
Cancellation
Impress at the order confirmation status of w230228A1740.
There is no Button. The W230301A745 I ordered today has a CanCell button in the order confirmation status, but not in the three-digit 740, but the Gold amount column is clearly marked in red letters.
I see a 740 screen, but it clearly says "Cancellation" on it, so is my Cancellation process on your web not working? Please email me first thing tomorrow morning. If not, please tell me why it is not working.
necessarily
View detail
Fits: HONDA CB1100, HONDA CB1300SF, HONDA CB1300 SUPER BOLDOR, HONDA CB1300SF, HONDA X-4
Cancellation
I made a mistake and changeCancellationHow many times do I have to create an email? View detail
Fits: HONDA CB1100, HONDA CB1300SF, HONDA CB1300 SUPER BOLDOR, HONDA CB1300SF, HONDA X-4
Cancellation method
There is no such thing as a "loss" next to the impresario.
Cancel both pieces.
Mr. Ueda
View detail
Fits: HONDA CB1100, HONDA CB1300SF, HONDA CB1300 SUPER BOLDOR, HONDA CB1300SF, HONDA X-4
Cancellation
Cancellation. How many times do you want me to say it, Mr. Ueda?
You say next to the side imprint of the order confirmation.
I don't know how many times you've had me do the same thing over and over again.
I know how I feel about White, and if this matter is not resolved, it won't lead to the next thing, which is why I only charge if I don't do anything on the web.
View detail
Clutch releaseOVER replaced with K-FACTORY
Although I preferred the appearance of the previous model, I bought it because it seems that they took measures to prevent the Piston and Cylinder from rubbing against each other.
(All three units previously used had Fluid leaks.)
When I installed it and checked the operation, the Clutch wouldn't cut...
After much trial and error, a 2mm thick shim was inserted between the Release piston and the Clutch push rod.
I managed to get it running...
Is this really for ZEPHYR1100...
I have been using K-FACTRYx3 OVERx1 clutch release but never had this symptom!
I hope to see improvements in the future ...
View detail
Fits: KAWASAKI NINJA ZX-14R, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1200, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200, KAWASAKI ZRX1100, KAWASAKI ZZR1100, KAWASAKI ZZR1100, KAWASAKI GPZ900R, KAWASAKI GPZ900R
The Piston was sticking.
P.S..
I forgot to write something in my last post, so I'll add it.
I forgot about it because it's not a problem to worry about so much once the installation is done perfectly.
First of all, this Release was sent in a crimped Vinyl bag, but when I took it out of the bag, the Piston was stuck and would not move! I thought about it for a while, and then I tried to pneumatically pressurize it, but it wouldn't work! Then I sprayed it with CRC. Then I sprayed it with CRC, put on a plastic head that matched the size of the pistons, and used a gold hammer to delicately tap it. Then I put the head of the plastic that fit the size on the head.
Thanks to this, the Wound of the pliers came on before I used it.
Sorry for all the bad reviews, but I'm writing the facts.
If you don't apply Grease etc. when shipping, you should do something. If you don't have a process to apply the Grease, you should do something about it.
View detail
Fits: KAWASAKI NINJA ZX-14R, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1200, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200, KAWASAKI ZRX1100, KAWASAKI ZZR1100, KAWASAKI ZZR1100, KAWASAKI GPZ900R, KAWASAKI GPZ900R
You think a Type K is a bad idea for a ZrX1200R?
About 8 years ago, I used KFACTORY's Clutch releaseA?Type and K-FAQ's Sprocket cover, but after 10000km, the Release leaked fluid. The cause is that the rubber ring of the piston in the release is worn out, and the piston interferes with the outside parts and there is a gap.
After that I went back to NORMAL and used the 14R Release.
This time, I ordered kType to change back to Aluminum Cut-out for Sprocket. As a result, I couldn't cut the clutches with Type K even though Type A is just right. However, NORMAL Sprocket cover + Type K can be used.
KFACTORY, what I'm trying to say is that Release and Sprocket cover add up to a very high price! You should display the compatibility exactly.
It's not a matter of just being able to use it.
By the way, the bolt of Release is too short to be attached to KFACTORY's Sprocket cover. This means that KFACTORY has known about it from the beginning, but they didn't disclose it to the public. That's right!
If I knew that, I wouldn't have paid 28,000 for it.
KFACTORY's Axle Slider also had one short bolt and could not be installed at times.
My faith in KFACTORY is gone, which is a shame because the Design Sense is great.
View detail