Reviews
Fits: HONDA MONKEY
3-pole coupler connector
Quality and texture information is no different from the std product It is compatible with Honda Std products for its usability You should have a wire stripper to buy together It's easy to install Buy based on cost performance and comparative brand preference with other products WeBike packaging is always great, arriving in a week for delivery and packaging Concerns, precautions, or advice on purchase If you connect the cable incorrectly, it is difficult to reunite There should be no failure from the beginning View detail
Power Supply Branch
I wanted a 110 2-pole terminal for charging and connection.:I wondered if it was a good idea since it is a Set, but substitutions with other inexpensive items would have sufficed. View detail
Recommended!
Replaced because OEM was ka Chica Chi!
It was almost a pontoon!
View detail
Terminals Waterproof and for insulation
Used for the crimping part of the Brake terminal.
Mainly for waterproofing purposes. To be honest, I thought two Shrinks would be enough, but I was attracted to the fact that there are various types of Covers and that they come with a Case. I will keep it for a while because I can use it in case of emergency.
View detail
The "Kill" is required.
If you use it in Minimoto's Kit, it's not a problem, but …
Wiring modification is required when using OEMParts or outside the company.
There is no Wiring diagram and even if you see it, the colors are different, so you need to have some understanding to Large strange.
View detail
I wonder if it could be a little cheaper, I'm looking for 8cm re-release.
Used for Clutch Cable of THRUXTON900
A little short. Is the 8cm one discontinued?
I cut and add the for Motorcycle's and use them.
It's expensive, isn't it? How about half price?
View detail
Useful to have
[How is it used?
I have been using Bullet Terminal for all of my Harness tweaking. Sometimes, when I have the motivation, I use AutoBacks and Color:I used to go to YellowHat to buy Coupler sets made by Emon, but it was a hassle to go buy them & expensive to buy them one by one.
Was the one you received as per Image?
It is just like the Image. Or rather, the quality is better than I expected.
Was the installation difficult?
Just turn the Wiring with Electric Works Pliers, Crimp and plug it into the Coupler.
It is useful to have a tool like this (https://www.webike.net/sd/2084789/) in case you plug it in by mistake. If you can pull it out cleanly, you can reinsert it.
How was your experience with it?
I no longer have to go out and buy every single thing, and I can put Wiring together neatly.
The fact that it comes in its own container is also a plus, as it saves me the trouble of going to the 100-yen store to buy Case.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
You can find other couplers from MINIMOTO (https://www.webike.net/tab/parts/bm/1409/br/1384/?q=%22%22&scls=2).
View detail
Universal Bellows Boots for Cable added to Clutch Cable
The NC750X has many areas of reduction in cost.
The clutch wire cable (let's make it hydraulic!) Dust Boots are also not included.
Both the Lever and Mission sides are bare.
The Lever side is made from Offfor Vehicle's Boots, but the Mission side is made from Bellows.
I found just the right one at Universal Product.
Minimoto's UniversalBoots with a total length of 50mm and a hole diameter of 3mm on the thin side (Wire side) and 6mm on the thick side (CableScrew part).
It was Exactly. I plugged it in while spreading it out without any processing.
This will protect you from rain, dust, etc. You can use it with peace of mind. I recommend it.
View detail
To install the MechanicalSwitch
I used it to convert the Zr-7S to Rear Sets.
I had been wondering what to do with the OEM parts for the Rear Sets, but there was no mount for the brake switch.
I considered getting a Hydraulic Switch, but I was hesitant because they are known for their high failure rate.
Thanks to this product, I was able to install the NORMAL Mechanical Type Brake Switch.
It is for MONKEY, but you can buy it for less than 1,000 yen, so you can use it for other than MONKEY.
By the way, I found out later that Kawasaki's ZrX1100 also seems to have these parts separately.
Maybe I should have done that since it's a Kawasaki?
I'll try to find the OEM Product number next time lol.
View detail
Fits: HONDA MONKEY
Used for MONKEY.
I used it for the Connector of the Tail part of MONKEY.
When you don't want to cut the Harness, you can use a thin slotted screwdriver etc. to hold the nail and remove and replace the Plain Type Terminal.
View detail
For Restore
It should be better than the wires of decades ago. View detail
It is attached to the Extension bar of the Φ22 like a sucker!
[How is it used?
I use it as a power on/off switch, not a kill switch.
I don't put it on the Handlebar, but on the Φ22 extension bar from the Handlebar, and it sticks to it without turning.
Was the installation difficult?
Quantity:It was easy to install just by removing the 2pc screws, passing them through the Handlebar and Extension bar, and then tightening the screws again.
How was your experience with it?
There is a solid sense of ON/OFF click, and the sense of use is conveyed properly.
[Included Parts:were they on?
None
[Notes]
I'm not sure if it's Waterproof or not, but I'm going to find out.
View detail
Fits: HONDA MONKEY
For use with the 6V MONKEY/GORILLA Main Harness for Replace.
I bought it in order to divert 6V MONKEY/GORILLA Main Harness (for 6V early stage) for Replace made by the company to my car (6V late stage:car with Regulator). In order to use their 6V MONKEY/GORILLA Main Harness, you need 4-pole coupler to connect Harness side 4-pole coupler to Battery separately. However, the Coupler on 6V MONKEY/GORILLA Main Harness side is 110 type 4-polewith Lock, so you can use 110 type 4-polewith Lock Coupler instead of this Coupler. View detail
Fits: HONDA MONKEY
Refreshed
The home-made Indicator Lamp was wiring with Bullet Terminal But when removing and removing the meter surround when you lose it, it is troublesome and Wiring is It's a mess, so I introduced it when I was organizing Wiring around Front Thanks to your help, it was Refreshing View detail
Fits: HONDA MONKEY
Wiring is neatly organized
I bought it to install the ICBlinker relay in Couplet-on
Home centeretc. doesn't carry it, so look around for motorcycle supply stores It's also a lot of work for me
For installation, if you can crimp the Bullet Type Terminal, it's easy I think you can
However, if you plug in the wrong coupler, it's Large strange to remove it, so you have to line up the other side well It's important to check
My hope is that the Coupler color would be available in Black
View detail
Fits: HONDA Dax 70, HONDA Dax 70, HONDA dachshund, HONDA dachshund, HONDA Shirley 70, HONDA Shirley 50., HONDA Shari (ST50), HONDA Shari (ST70), HONDA Shari (ST50), HONDA Shari (ST70)
Key cylinder replacement
I accidentally lost my …key …key cylinder I decided to do …
Wiring is different from my DAX, so I had to stare at the wiring diagram and see if I could find the right one Wiring was adjusted and installed
View detail
Fits: HONDA MONKEY
no problem
It is the same shape as the Connector of the Regulated Rectifier for moped of Honda cars So it is useful when you play with the electrical system
Used to replace the Regulator in pure AC vehicles with a Regulated Rectifier I did
The lock is stiff and difficult to pull out, but on the other hand, it's secure and secure
View detail
Fits: HONDA MONKEY
It's not easy to sell
I used it to replace the Blinker relay with an ICRelay
I didn't want to do anything to the vehicle body Harness, so I asked ICRelay's Wiring for this I put the product on and made it Couplet-on
The 2-pole and 4-pole ones are readily available at home centers and supply stores, but This shape of coupler was helpful because there are not many places that sell this shape of coupler
View detail
Replacement wire harness for Honda Z50
Here is a great replacement wire harness for my 1976 Honda Z50. Fitted perfect with all the correct conections. See picture with harness against frame and all other parts fitted to it perfect. View detail
Quantity : Purchase Set items
To finesse Wiring, 0. Since it is common to use Size less than 3sq, Shrinkable Tube also wanted Small Size. I thought about buying only 2 mm Tube, but since it is imprecisely Quantity with abundant Size with Case : I bought a set item
Performance is the same as other Tube. , The shrinkage factor is about 50%. It was easy to use because it was short cut shortly from the beginning
Shrinkable Tube is a necessity if you finger Wiring, Quantity with abundant Size : It is convenient because you will not buy it after you purchase a set item
View detail