Reviews
Replace with new Connector
The Coupler I was using was discolored and hard to remove, so I purchased a new one to replace it.
Male, MeSpin, and Coupler set items were inexpensive and saved me a lot of money.
View detail
Refreshingly summarized
I purchased this for use with a Switch on a Cycle alarm that gets its power directly from the Battery. The reason why I needed to install the Switch is that I do not use the Alarm when I leave it at home, so I could not accidentally operate the Quantity:We decided to install a switch just in case it is set to run while we are away from home, or to prevent the battery from going up because of it. I don't think it will malfunction if I don't operate it in a strange way, but just in case.
Cycle alarm is intended to be used when leaving the vehicle for touring, shopping, etc., so we plan to install a Switch in the Space under the Seat and use it to turn the Switch on when departing if Cycle alarm use is expected.
Initially, we had installed our own Torg Switch, but it did not fit into the Space under the Seat, so we purchased this Torg Switch to replace it.
I am satisfied that it fits tightly, but I think it is a bit expensive.
View detail
exchange
The Connector we were using was discolored and deteriorated, and was hard to detach and attach, so we replaced it.
It is sold as a Single Item, so I was able to purchase only what I needed.
View detail
Connection
It is used for redoing Wiring.
Just Right Quantity:It was just the right number of pieces to reASSY in a set.
View detail
For UniversalMeter installation
In replacing the Meter with KOSO's Multimeter, we did not want to damage the harness on the body side, so we purchased a 110-type 9-pole and 3-pole Coupler and made an intermediate harness so that the new Meter could be detached with the Coupler.
The product was a perfect fit, the terminals were solid, and the product was safe to use. The coupler is compatible with the coupler attached to the harness on the body side of the car without any problem, and it can be attached and detached smoothly.
I think it was a bit of a waste since I only used One Side, but I will keep the extra one in a Large Cutout until I need it some other time.
View detail
Fits: HONDA CB1100 F (SC11), HONDA CB1100 R (SC05), HONDA CB1100 R (SC08), HONDA CB750 F (RC04), HONDA CB900 F (SC01), HONDA CB900 F (SC09)
rework
I bought this for re-installation because I pulled the Cable when removing the Connector and it fell out.
Single Item sales were helpful because I could choose the number of items to purchase.
View detail
Fits: HONDA CB1100 F (SC11), HONDA CB1100 R (SC05), HONDA CB1100 R (SC08), HONDA CB750 F (RC04), HONDA CB900 F (SC01), HONDA CB900 F (SC09)
spare
For 110 Type Coupler, it is a repurchase for another Cable to confirm the operation after connecting to the Coupler.
Single Item sales were helpful because I could purchase only the number of items I needed.
View detail
Connector Replacement
The MotorConnector installed is old and discolored, so we are purchasing a new one for replacement.
The TAB, receptaclePin, and Connector set was reasonably priced, but I was able to exchange it for a new one.
View detail
Safe and DAYTONA products
I purchased this product because the handling of the Brake switch has changed due to a change in the Braking system.
We chose DAYTONA because we thought it was not the part to go out of our way to buy OEM.
It is a safe part that is neither too good nor too bad, but it would be surprisingly useful if there were a lineup of parts.
View detail
Terminals Waterproof and for insulation
Used for the crimping part of the Brake terminal.
Mainly for waterproofing purposes. To be honest, I thought two Shrinks would be enough, but I was attracted to the fact that there are various types of Covers and that they come with a Case. I will keep it for a while because I can use it in case of emergency.
View detail
Used in Horn's Flat Terminal
The Wiring for the car Both Sides was short and was used to extend it. View detail
MC286V MONKEY/GORILLA Main Harness
OEM Product was discontinued, MC21 and others were sold, but MC28 was sold for MC28, so it was purchased immediately.
It is a bit expensive, but OEM Product is discontinued, used ones are also quite expensive, and there is no worry about contact failure; new ones are safer.
Some OEM Product and Connector types seem to be different, but it does not matter as long as they can be connected.
For some reason, the price sold by the producer was higher than the price of the product, and the purchase here was cheaper, free shipping, and the Point was also reduced.
View detail
Fits: KAWASAKI Ninja H2 SX SE, KAWASAKI VERSYS1000 SE, KAWASAKI Ninja[Ninja ] H2 SE, KAWASAKI Ninja[Ninja ] H2 SE+, KAWASAKI Ninja[Ninja ] H2 SX, KAWASAKI Ninja 1000, KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000, KAWASAKI VERSYS 1000 SE
I don't know why, but there's no instruction manual.
I was confident that I could manage to install it because I had installed it on a Honda car in the past, but as a result, I failed. I am wondering why the instruction manual is not included in the kit. Is there an intention to prevent individuals from making their own work? View detail
Hazard Switch.
To the Hazard switch on the CUB.
It looks like a HazardButton, which is good.
View detail
Shipping Adjustment
Purchased to adjust price for free shipping.
Unlike ordinary Tie Wrap, this is a Release type, so it has the advantage of being easily reusable, and we plan to use it for harnesses around lights that are moved a little more frequently.
Quantity:1 Set of 2pcs. so I don't think it is cosmetic. I don't think there is any Merit to buy except for price adjustment.
View detail
SwitchBody's tucking & hiding of Wiring is messy.
I've added a Headlight to the Basket of the CUB, as well as a PRO.
Purchased along with Torg Switch, also from Emon, for switching between high and low.
Perhaps it's not so much precision despite the dedicated product, or perhaps it's
SwitchBody's tucking & hiding of Wiring is messy.
Above all, Plastic's Cover.
The fact that it doesn't fit tightly & comes off easily is something I would like to see improved.
View detail
For Wiring Summary
This is essential where Wiring can be put together or rubbed.
I guess it just can't help but get cracked in a few years when exposed to UV rays.
It is good that it can be installed after Wiring.
View detail
It is longer than the one that comes with the Kit.
I used it for my FZ750 Full kit.
I ordered this one because the cord that came with the Kit was very Tight and I had concerns.
The shape of the Connector was exactly the same as the Kit. And the length of the cord is about 20 cm, so there is plenty of room.
If possible, we would have liked the attached cord to be this length.
View detail
Fits: その他 , HONDA NSR250R, HONDA NSR250R
For Waterproof Protection
Honda Series WaterproofBullet TerminalCover10 PairsQuantity:It was a set, so I bought it to protect the BlinkerWiring section, etc., and to use it for waterproofing.
The price is not that bad, there are a few of them, and the Rubber shape is not bad.
View detail
Can be inserted into a hole and fixed in place.
It is a product that can be inserted into the hole and fixed with Tie Wrap.
Thank goodness I usually don't sell Rose.
View detail