- Home
- Product reviews
- Search reviews
- Motorcycle Parts
- Electrical
- Switches / Harnesses
Reviews
Chinese quality
[How is it used?
I installed Fog Lamp on FZS600 and introduced IndicatorSwitch with Fog Mark as a measure against vehicle inspection.
Was the one you received as per Image?
The quality is a bit disappointing. The Fog Mark was mounted on the Body with a slight tilt. I tried to fix it in the correct position by removing the rubber cover of the bellows, but it was fixed so tightly that I could not do it. I tried to remove the rubber cover from the bellows and fix it in the correct position, but it was not possible because it was firmly fixed in place.
Was the installation difficult?
I installed it on a DRC bar mount, but it does not match the bar diameter slightly and there is a gap on the mounting surface, but I managed to install it. I used Screw Loosening Fluid because the gap was not tight enough to fit the bar and the Screw was about to loosen.
How was your experience with it?
I was worried that the blue light of the Indicator might be bothersome to my eyes when it is turned on at night, but it did not bother me much while driving. During the touring, I drove in heavy rain several times, but the waterproof performance was fine.
[Included Parts:were they on?
Includes a complete set of parts needed to turn on the fog.
[Was there anything that disappointed you?
The functionality as a Switch is fine, but the quality is not so good.
Other items that would be helpful
(1) Point of attachment or hang:Depending on the mounting position and angle of the Switch, Blue light may be a concern when driving at night?
2) Availability and clarity of Instruction Manual:I think it is relatively easy to understand because it is illustrated.
(3) Note:Ensure that Wiring is handled without undue force and Connectors are connected.
4) Items to buy together:Screw loosening fluid.
(5) Opinions and requests to Manufacturer:Improve quality and assembly accuracy.
View detail
MOTO LED for Fog LampSwitch HarnessKit
The configuration of the product is large and good, but the crimp on the wiring terminal of the Relay and Fuse part is not good enough, and it came off during the wiring. I would like you to use a solder or something to prevent the wiring from coming loose. View detail
The Switch width is narrow and easy to install, but the quality of the Harness itself is a bit unsatisfactory
[How is it used?
Purchased for the installation of the company's Fog light and Moto LED.
Was the one you received as per Image?
It consists of Harness, Relay, Switch, and Bullet Type Terminal, as per Image.
How was your experience with it?
Since there are Sea Rings and Cable exteriors in the necessary places beforehand, it can be pimped out if you are not particular.
[Points to note]
There are three things that bothered me. I'm sure they are fine for use with the company's LEDs.
1. The input and control wires of the Relay are on the same wire, and the car Both Sides +− and fog +− 2 sets of 6 wires are on the Wiring end.
In the Instruction Manual, the car Both Sides + line is directly linked to the battery or Accessories, but the former does not link to the main key and the latter does not link to the battery.
With the latter, I didn't think Relay made much sense because of the load on the ACC power supply.
(I modified the Relay control line to connect to ACC)
2. Since the core wire of Wiring is about 0.2sq, please be careful to connect Lamp with high load.
3. The Bullet Type Terminal for the fog is crimped with Male and Female terminals on the + and +minus; sides.
+There is a risk of shorting between Body ground when the wire is disconnected. (I have replaced it.)
How did it compare to other products?
We saw very few fog harnesses for motorcycles from other companies, and the ones we did see were almost double the price of this product.
From the price, I thought that the above-mentioned notes might be acceptable, but please be careful when you divert it.
View detail