Reviews
MINIMOTO 6V MONKEY6V MONKEY/GORILLA Main Harness
I purchased the 6V MONKEY/GORILLA Main Harness for MONKEY/GORILLA last time and this time I purchased this one because it comes with Silicon Rectifier Fire and the price is reasonable. I purchased this product because I can do the wiring without any problem. 6V OEM product is discontinued, so I am very thankful for this product. View detail
Recommended!
Replaced because OEM was ka Chica Chi!
It was almost a pontoon!
View detail
Terminals Waterproof and for insulation
Used for the crimping part of the Brake terminal.
Mainly for waterproofing purposes. To be honest, I thought two Shrinks would be enough, but I was attracted to the fact that there are various types of Covers and that they come with a Case. I will keep it for a while because I can use it in case of emergency.
View detail
The "Kill" is required.
If you use it in Minimoto's Kit, it's not a problem, but …
Wiring modification is required when using OEMParts or outside the company.
There is no Wiring diagram and even if you see it, the colors are different, so you need to have some understanding to Large strange.
View detail
I wonder if it could be a little cheaper, I'm looking for 8cm re-release.
Used for Clutch Cable of THRUXTON900
A little short. Is the 8cm one discontinued?
I cut and add the for Motorcycle's and use them.
It's expensive, isn't it? How about half price?
View detail
Universal Bellows Boots for Cable added to Clutch Cable
The NC750X has many areas of reduction in cost.
The clutch wire cable (let's make it hydraulic!) Dust Boots are also not included.
Both the Lever and Mission sides are bare.
The Lever side is made from Offfor Vehicle's Boots, but the Mission side is made from Bellows.
I found just the right one at Universal Product.
Minimoto's UniversalBoots with a total length of 50mm and a hole diameter of 3mm on the thin side (Wire side) and 6mm on the thick side (CableScrew part).
It was Exactly. I plugged it in while spreading it out without any processing.
This will protect you from rain, dust, etc. You can use it with peace of mind. I recommend it.
View detail
To install the MechanicalSwitch
I used it to convert the Zr-7S to Rear Sets.
I had been wondering what to do with the OEM parts for the Rear Sets, but there was no mount for the brake switch.
I considered getting a Hydraulic Switch, but I was hesitant because they are known for their high failure rate.
Thanks to this product, I was able to install the NORMAL Mechanical Type Brake Switch.
It is for MONKEY, but you can buy it for less than 1,000 yen, so you can use it for other than MONKEY.
By the way, I found out later that Kawasaki's ZrX1100 also seems to have these parts separately.
Maybe I should have done that since it's a Kawasaki?
I'll try to find the OEM Product number next time lol.
View detail
Ignition lock for Super Cab
I bought this ignition lock instead of the old one. the old one sometimes lost contact when driving over irregularities, which led to the fact that the turn signals and the display were turned off. The lock itself fit very well and the workmanship is very good, but the wiring needed to be redone as I have an electric starter. Therefore, the pins themselves had to be redone.
I recommend taking it if you have a problem or you have lost your keys. An inexpensive way to solve these problems.
-------------------------------------------------- -------- I bought this ignition castle in return old, because The old one sometimes moved contact when driving at irregularities, which led to the turning and display turned off. The castle itself approached very well and the quality of execution is very good, but the wiring needed to remake, because I have an electric starter. Therefore, the Pins themselves needed to remake.
I recommend to take if you have a problem or you lost the keys. Inexpensive way to solve these problems.
View detail
For Restore
It should be better than the wires of decades ago. View detail
It is attached to the Extension bar of the Φ22 like a sucker!
[How is it used?
I use it as a power on/off switch, not a kill switch.
I don't put it on the Handlebar, but on the Φ22 extension bar from the Handlebar, and it sticks to it without turning.
Was the installation difficult?
Quantity:It was easy to install just by removing the 2pc screws, passing them through the Handlebar and Extension bar, and then tightening the screws again.
How was your experience with it?
There is a solid sense of ON/OFF click, and the sense of use is conveyed properly.
[Included Parts:were they on?
None
[Notes]
I'm not sure if it's Waterproof or not, but I'm going to find out.
View detail
Fits: HONDA MONKEY
For use with the 6V MONKEY/GORILLA Main Harness for Replace.
I bought it in order to divert 6V MONKEY/GORILLA Main Harness (for 6V early stage) for Replace made by the company to my car (6V late stage:car with Regulator). In order to use their 6V MONKEY/GORILLA Main Harness, you need 4-pole coupler to connect Harness side 4-pole coupler to Battery separately. However, the Coupler on 6V MONKEY/GORILLA Main Harness side is 110 type 4-polewith Lock, so you can use 110 type 4-polewith Lock Coupler instead of this Coupler. View detail
Fits: HONDA MONKEY
Refreshed
The home-made Indicator Lamp was wiring with Bullet Terminal But when removing and removing the meter surround when you lose it, it is troublesome and Wiring is It's a mess, so I introduced it when I was organizing Wiring around Front Thanks to your help, it was Refreshing View detail
Fits: HONDA Dax 70, HONDA Dax 70, HONDA dachshund, HONDA dachshund, HONDA Shirley 70, HONDA Shirley 50., HONDA Shari (ST50), HONDA Shari (ST70), HONDA Shari (ST50), HONDA Shari (ST70)
Key cylinder replacement
I accidentally lost my …key …key cylinder I decided to do …
Wiring is different from my DAX, so I had to stare at the wiring diagram and see if I could find the right one Wiring was adjusted and installed
View detail
Main Key Cylinder for Super Cub
Hello Webike! I bought this ignition switch to replace the old original ignition switch. The old ignition switch had poor electrical connections and I decided to replace it. The workmanship is good, the lock fits perfectly in the original place. The electrical connector matches the original wiring. This ignition switch will not fit Honda Super Cub fi with injection engine! Thank you Webike for fast delivery and quality product! Hi Webike! I bought this ignition switch in exchange for the old original ignition switch. The old ignition switch had poor electrical contact and I decided to replace it. Workmanship is good, the castle perfectly fell into place of the original. The electrical connector went to the original wiring. This ignition switch is not suitable for Honda Super Cub fi with an injection engine! Thank you Webike for the fast delivery and quality product! translated by Google Translator View detail
Fits: HONDA MONKEY
no problem
It is the same shape as the Connector of the Regulated Rectifier for moped of Honda cars So it is useful when you play with the electrical system
Used to replace the Regulator in pure AC vehicles with a Regulated Rectifier I did
The lock is stiff and difficult to pull out, but on the other hand, it's secure and secure
View detail
Replacement wire harness for Honda Z50
Here is a great replacement wire harness for my 1976 Honda Z50. Fitted perfect with all the correct conections. See picture with harness against frame and all other parts fitted to it perfect. View detail
Quantity : Purchase Set items
To finesse Wiring, 0. Since it is common to use Size less than 3sq, Shrinkable Tube also wanted Small Size. I thought about buying only 2 mm Tube, but since it is imprecisely Quantity with abundant Size with Case : I bought a set item
Performance is the same as other Tube. , The shrinkage factor is about 50%. It was easy to use because it was short cut shortly from the beginning
Shrinkable Tube is a necessity if you finger Wiring, Quantity with abundant Size : It is convenient because you will not buy it after you purchase a set item
View detail
It's like OEM!
I replaced it because the OEM switch of KDX 125 SR was broken by rust and degradation of plastic part.
I was able to attach it without any problems with shape, performance, price.
OEM is a push type of a round Button, it was hard to know whether it was ON or OFF at a glance, so I hated it very much, but it is easy to understand after the exchange so I think that this is OK with OEM.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Things are not bad
The explanation was difficult for me to understand, but it was Harness for Chinese Engine made by Minimoto. Since it was used for MONKEYOEMEngine, it was only for me to use Wiring's parts removal and electrical system. Wiring diagram is also confusing compared to Posh. View detail
Used for Mini bike race
Kill switch and other switches are together and can be used for various things.
It works in conjunction with Stopwatch, and it is used for Speed ??Limiter.
These parts are useful for Case where there is no place to attach various switches around Handlebar.
View detail