Reviews
A quality low-profile blinker kit
The kit I purchased was well packaged and tailored for installation on a V-Strom 650. All parts appear to be good quality and ready for immediate installation on the bike. The kit includes wiring adapters to suit the bike (bullet connector to 2-pin Suzuki connector) and a new 7-pin LED blinker relay. Installation was easy for someone with moderate experience. Tools required: open-end wrenches (8~12mm), hex key wrenches (4~5mm), 10~12mm socket. The rear fender of the bike must be removed to access the wiring and remove the existing blinkers. Routing the wiring through the adapter plates, washer and nut requires patience and a delicate touch. Aside from that, it's a matter of securing connections with electrical tape and securing the wiring to the frame. The kit is quite bright and very visible, even during the daytime. The blinkers are all mounted on flexible stalks, so they should survive if the bike is dropped. Overall, I am very pleased with the purchase. View detail
There is a sense of security dedicated to the car model.
DL1000 V-STROM650XT ('22) The product has been installed in a
It will be used in conjunction with Hepco&Becker's Engine Guard,
The bracket of the Radiator part was a little bit hit by the Guard,
The installation was only a little difficult, but it was almost interference-free. I think there may be individual differences, so this is just for reference.
Because the connection between the Fog Lamp and the included Harness was a Flat Terminal,
We changed to WaterproofCoupler just in case.
The brightness is sufficient for an auxiliary light,
Cutline is also solid, so I don't think it will bother oncoming traffic.
Considering the price, the texture might be a bit lacking,
If you are concerned about this, you should consider another product.
View detail
Fits: SUZUKI GSX-S125, SUZUKI GIXXER 250, SUZUKI GIXXER SF250, SUZUKI GSX-R125, SUZUKI GIXXER 150, SUZUKI V-Strom250 SX
Extension Harness Min.
Quantity of 1 Set for 1 Vehicle to install TRL2Blinker:Set.
TRL2 LED Blinker*4
Mount for TRL2*4
Extension Harness (long)*2
Extension Harness (short)*2
MicroIC Blinker Relay*1
Small and very Stylish
The mounting is done by sandwiching the Mount with the Plate, and since the hole is small, the Bullet Type Terminal is inserted while shifting it slightly.
The price is almost the same if you buy them individually, but you save money for the Extension Harness.
The included MicroIC Blinker Relay is about the size of a small finger, so you should have no trouble finding a place to place it, but the terminals are bare, so be careful not to touch the Gold Genus.
View detail
Flashing relay
GSX-1000 L3 is installed.
Since Relay is in the Blue circle, it is easier to Rose Seat Cowl as much as possible, and since Relay itself has a protrusion to prevent it from falling out, Space is needed to knead it lightly with Minusetc.
Things are OEM same etc. and not so good or not so good.
View detail
Very happy with purchase
Bought this as a north American buyer, received the item 4 days later, perfect packaging. The light diameter is the same as the OEM on the Yamaha XSR900. Very please with the quality of the product. View detail
I am satisfied
Degrease the body side and the back of the rim, and use the supplied double-sided tape.
Just paste three places.
I'm a little concerned about adhesion because of the cold weather.
Warm it up with a heat gun, etc., and then use masking tape.
It would be good to hold it down and take a curing period.
The two holes were placed down.
Originally, the current OEMLight shines because the Rim is transparent.
I don't know exactly what the difference is, but I've been using Plating for the other Parts.
I am personally satisfied because I want to unify the two.
It is easier to understand than the Blinker Rim.
View detail
It was worth the price.
I was a little disappointed because it was an Image that glowed a little brighter.
Well, I can barely see Meter, so I'm going to use it as is for now.
View detail
Slim impression
I purchased these to install on my 2014 S1000RR.
The second model has been replaced by a narrow LED blinker, which is also attractive in its own right, but we wanted to make the most of the SS design, so we decided on this less conspicuous product.
The installation itself is completed only with Torque and +Screw.
Instruction is also clear and Quantity:Pair (for Left and Right) There is also an indication so you will not make a mistake.
However, since it is LED, high flasher will occur. I don't mind it that much, but those who care about it may be bothered.
Well, when you are on it, you can't see it because it is a very Compact Blinker.
Note that the Crimp on the Connector and wire may be a little weak and may come loose. Be careful when attaching and detaching.
View detail
Fits: HONDA SUPER CUB 50PRO, HONDA SUPER CUB 50, HONDA CROSS CUB50, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA CROSSCUB110, HONDA SUPER CUB110, HONDA CROSSCUB110
Does not fit 23 year old JA56 products
I ordered several parts from We Bike and installed the ones that fit.
Surprisingly, there are too many incompatible parts.
It does not fit the JA56 model, which is an officially imported product from Korea.
Machining is required when installing. Please keep this in mind when purchasing from Korea.
-------------------------------------------------- -------- We are ordered by ordering various parts from Webike, but there are too many parts that are unexpectedly compatible. It is not suitable for the JA56 model, the official imported product of Korea. When mounted, processing is required. Please refer to the purchase of Koreans. Powered by Google Translator
View detail
Sense of security.
If you are looking for a Square type, this is the one you should choose.
I personally think that this is the best choice in terms of tightness, design, and quality. I can feel that each item has been inspected one by one, which gives me a sense of security.
I am very happy with the Large size.
View detail
MONKEYTachometer out-of-lighting measures
The lighting bulb of Takex Tachometer, which was installed in MONKEY, went out, so we installed KIJIMA's lighting bulb as a Universal Product, and it worked fine.
We will fit the product with confidence, so please use it as a reference!
View detail
Excellent visibility.
As expected from a first-class manufacturer. The quality is excellent, and is not as good as some cheap blinkers. The price is high, but that's all there is to it. If the car body side can use Bullet Type Terminal as it is, there is no problem, but if Coupler is used, modification is required. The luminous intensity is also high.
It is outstanding and highly visible.
View detail
BANDIT1200 2006 F/E used for LED conversion
I used BANDIT1200 FE Blinker LEDs and the only LED Bulb I used was JAPAN's Matsu Stripe. The price may be higher than Chinese products, but it is an old car and I thought it would be troublesome if I found a defective Chinese product, so I decided to go for peace of mind.
Front Blinker Valve Maz Stripe L820D OR
Rear Blinker Valve Mazda Stripe L820S OR
Tail lamp and License Plate Light have also been converted to LED.
Tail lamp bulb Maz Stripe L820D RE
License Plate LightValve Maz Stripe L742H
Relay can be accessed by loosening and removing the Left Side Cover with a single hex.
Tail lamp is located deep inside the cowl, so it was a little bit of a hassle to reattach it, but no problem.
BANDIT1250S Motorcycle Travel's blog was used as a reference. Thank you very much.
https://819oba3.com/bikelife/led-lights-bulbs/
*I was too lazy to look it up, so I looked at the blog and ordered the same thing without thinking w
View detail
Stylish with no sense of retrofitting
I had been thinking of converting Blinker to LED for a while and decided to do it since I could afford Gold.
The shape &Quality of the product is fine.
I had planned to install it quickly and finish it quickly, but there was an unexpected pitfall....
The installation itself can be done in two hours, both front and rear.
However, it does not work properly just by installing it normally.
I did an operation TEST and all 4 of the front and rear ones blinked at the same time and went into Hazard state.
I checked to see if I had made a mistake with Wiring, but no problem.
When this happens, the suspicion is often that some special processing is required.
Net, I found that by setting up a rectification diode in the wiring of the blinker indicator in the Meter, the rectification diode can be used.
We were informed that the problem is going to be solved.
I heard that they also sell a Wiring Kit for it, so I bought one at a local mass retailer.
I did a full Rose of Cowl and took out the Meter unit and did the Wiring process and it worked fine.
I had no prior knowledge of the replacement work, so I struggled with unexpected pitfalls....
If you are going to do DIY installation work, do a lot of research before you do it.
View detail
Mounted on CD50
Used in CD50 head lamp relocation.
The Clamp can be split and mounted without removing the Fork from the Bridge.
The included Rubber plate can be used for 27mm thin Tubes.
Rubber and gold plates are attached to the square PRESS part of the bracket with double-sided tape, but they were peeled off when they arrived.
I am able to use it without any problem.
However, because of this structure, if a blinker is attached here, the rubber and gold plates tend to shift when the angle is adjusted.
View detail
Fits: HONDA CT125 HUNTER CUB, HONDA CT125 CT110 HUNTER CUB
It has a lot of stuff around the front, so ….
Since there are many things around the front, I prepared long bolts for the front carrier and windshield respectively, and was able to install the wiring without opening the headlight. View detail
Excellent cosmetic Headlight
I have a TOWN MATE 90 with a front basket, and I had a headlight installed in front of the basket, but it was damaged and needed to be replaced, so I was looking for a good replacement and found this one. The simple construction makes it very universal, and I think anyone who is familiar with the work can attach it in any way they like. The price is very low for a similar headlight, which I think is a big plus. View detail
For Stock
I have already purchased this product last time and bought it for Stock.
It's for old Custom parts,
In the countryside, items are difficult to obtain.
Thanks.
View detail
Small but bright!
Small, not sure if it's on or not, Parenthesis is good!
Japanese Vehicle Inspection Correspondence and brightness is perfect!
The wire coming out of the Body is very thin, so be careful when installing it.
I was on edge because it looked like it was going to come off.
View detail
This is a review of the headlight rim.
When installing, it is installed on top of the original rim. Suitable for CT125. It is a 3m tape fixation type, so please replenish it enough before installation.
It's a minor tuning, but those who recognize the CT125 will immediately recognize the small change.
I think the price is reasonable too. It would also be a good idea to be careful in case of rain. I think it would be better to install the headlight guard on top of the rim after installing it.
Recommended! -------------------------------------------------- -------- It is a structure installed on the pure rim when installing. Suitable for CT125. 3M tape is fixed and please supplement it more enough. It's a trivial tuning, but if you look at CT125, you can find out at a small change. I think the price is also appropriate. It would be nice to be careful about rainy weather. After installing the rim, it would be better to install the headlight guard on top of it. Recommended! Powered by Google Translator
View detail