Reviews
A little bit of installation. ? Will be
As others have mentioned in the review, the convex part to fit the lower cosmetic bolt×1 and the upper OEM bolt×2 do not fit if they are left as they are.
The lower inner side is fitted by grasping and compressing the inner side with your hand.
I am a little impatient because this area is not in the Instruction Manual.
I am not sure if it is only for the 2023 model, but there is a 5mm pin hole on the inner cowl side, which is flooded with slop water, so I filled it with Pate.
You can see it when you actually fit it, but it is a pin hole that does not bother you that much, so those who do not mind may not mind it.
I wanted the Fender angle to be a little more warped, but since it is a regulatory Limit, other Fender Eliminators may be the same.
View detail
Conforms to ST1000 Regulation
I purchased the Tail Lamp to compete in the ST1000Class at the regional championships.
I purchased the DRC Tail Lamp because it meets the ST1000 Regulation.
Brightness is not a problem.
View detail
Fits: KAWASAKI D Tracker 125, KAWASAKI D Tracker X, KAWASAKI KLX125, KAWASAKI KLX150, KAWASAKI KLX250, KAWASAKI KSR110, KAWASAKI Ninja 250, KAWASAKI Ninja 250R, YAMAHA FZ1, YAMAHA FZ1 Feather, YAMAHA FZ6 04-17, YAMAHA FZ6-S Feather, YAMAHA FZ8, YAMAHA MT-01, YAMAHA MT-07, YAMAHA MT-09, YAMAHA TDM900, YAMAHA V-MAX 1680, YAMAHA WR250R, YAMAHA WR250X
I wish it was 10mm diameter.
Purchased to replace LED Blinker.
Maybe it's compatible with Yamaha stuff or something.
Since I could not be sure, I bought a DRC product that I could be sure of.
This product is used between two pieces, so the front and rear blinkers are interchangeable.
2Quantity:Set is required.
Since the mounting hole of this product is 8mm diameter, the Screw diameter of the Blinker to be installed is also 8mm diameter.
The 8mm blinker is used, but there are surprisingly few 8mm-diameter blinkers.
The problem is that most of the products sold at low prices are 10mm diameter and there are very few options.
View detail
This is a highly Universal Tail lamp.
Universal Tail lamp
[How is it used?
I had been looking for a replacement for my KSR-II for many years, but I could no longer install the OEM Product's Tail lamp, so I went to Webike to find one. However, I found this product when I was looking for a replacement for the OEM Product's Tail lamp.
Was the one you received as per Image?
It is a product that is more than an image in the form that has good visibility with the Edge effective design while being compact, and also has universal characteristics that can be installed from off-road motorcycles to road sports type motorcycles without any sense of discomfort. It is a product that is more than just an image.
Was the installation difficult?
As mentioned above, this is a work to install a bracket for Fender Eliminator, which is a self-made bracket, so the drilling and wiring processes are performed in actual products, so it may not be of much help.
After installing it on the Fender Eliminator, all you have to do is connect the wiring of this product to the wiring for the tail lamp on the body of the vehicle, but this product does not have the wiring that is often found in this type of product. "Bullet Type Terminal Spec
Modern motorcycles have connector terminals, so it is easy to find a connector that fits the vehicle body on KITACOConveniencePartsetc. and modify it to make a simple connection.
Fortunately, KSR-II has Bullet Type Terminals for most of the terminals that connect to the lights, so we were able to connect without any modification.
How was your experience with it?
There are no problems with the functionality of the LED bulbs, which have been in place for several years now and are functioning as well as they did immediately after installation.
My personal impression is that the rounded design of the KSR Tail would fit better with the rounded design of the Tail lamp than the pointed design of the Tail lamp. I think that the rounded design of the KSR Tail lamp fits in better than the sharp design.
I had a friend install it on his WR250 after that, and the shape of the tail and the design of this product matched very well, and I honestly thought Parenthesis was good (this is just my personal opinion).
[Included Parts:were they on?
It was a Simple Package with only Body and Instruction Manual.
[Was there anything that disappointed you?
Not at all.
Aside from the above mentioned compatibility, which is a matter of personal preference, I have no complaints about the product design or the kinability of the product.
Other items that would be helpful
Point and hang of installation
This product is a Tail Lamp product, but a vehicle-specific kit that uses this product is also sold by DRC.
The price is a little bit higher, but the Bracket for each car model is also of high quality and you will not feel any discomfort after installation. It's a Manufacturer's product." I am convinced that this is the right product.
For those who, like me, cut, paste, and fabricate to install, please measure the dimensions carefully or do your best to install the product as-is.
[Availability and clarity of the Instruction Manual
An Instruction Manual is included in the package.
[Notes]
Nothing in particular, just be careful not to misplace Wiring.
[ITEMS TO BUY TOGETHER
As I mentioned above, this is also available from KITACO and other companies. OEM Type Connection Terminals by Manufacturer will allow one-touch connection to Harness on the car body side.
Since the method of fixing to the car body varies depending on the car model, it may be better to try a temporary assembly before full-scale installation.
First, check the fixation method by placing it on the vehicle in which you want to install it.
[Opinions and requests to Manufacturer
Please keep up the good work in maintaining prices as much as possible and keep selling for a long time to come.
View detail
Thank goodness I can buy only Lens.
I know that Blinkers on off-road vehicles are often damaged in a fall, but it is very nice to know that DRC products are available only in Lens and can be replaced.
I was impressed that DirtFreak products understand Off-roadUser very well.
View detail
Fits: KAWASAKI KLX250, KAWASAKI D-TRACKER-X
For those who want to make the silhouette of the car look sharper...
I am an uncle who loves Fender Eliminator Large, so I was the first to replace it when I bought D-Tra.
Please note that if you buy only the product, you will not be able to use the reflector or the OEMB blinker, so you will need to purchase a reflector and a bracket to attach the OEMB blinker, which you may have lying around, before you can finally drive the product on public roads.
Now, as you can see in the image, the weight is reduced due to the overwhelming difference in area.
This doesn't mean that it is lighter or anything, but it is lighter (lol).
I personally thought that the Rear area was cleaned up and the finish was very cool.
View detail
Simple shape
OEM and replacement.
There was a Space-like difficulty in installing it on the Fender Eliminator Kit.
No Large problems.
As said in other Reviews, note that Body strength is low.
Also, be careful when converting old cars to LED because it is easy to have problems with Relay.
View detail
Fender Eliminator and led
[How is it used?
Fender Eliminator conversion made it look like I like it, as per Image.
Was the one you received as per Image?
It was heavier than I expected.
Was the installation difficult?
I had a little trouble with the installation.
The lower mounting part attaches to the outside of the
I couldn't figure it out and tried to install it on the inside.
I was worried that it would not fit.
How was your experience with it?
It's good
I have no protection against rain or water from washing the car.
We'll see how it goes.
[Included Parts:were they on?
Screw has some parts to be diverted.
[Was there anything that disappointed you?
Instruction Manual, because we are making it universal.
I don't know much about it.
I feel like I can handle it.
Other items that would be helpful
Buy together
Reflector kit for D45-07-300 has been
I think it is necessary.
View detail
What a surprise to find out that it is LED.
The NORMAL Tail area is very heavy.
It is also heavy in appearance.
So the familiar DRC makes it look good and lightweight.
Smoked lenses make it even more beautiful.
Tail Bulb What are we going to do? Do we have to make our own?
Thinking that maybe it was LED from the beginning?
The product I received was LED and all I had to do was Bullet TerminalWiring.
There is no mention of LED in the DRC product description, and when I saw the picture, I wondered if it was LED. I just thought it might be an LED.
This completes the LED conversion of the MD44.
NumberWhite lighting is also available, so driving on public roads is OK!
Other cheap ones do not have White lighting and can be cut off for poor maintenance KIP. Please be careful.
Bullet TerminalWiring can do the installation by itself (I also performed the soldering just in case).
You must be able to disassemble and remove the Blinker yourself.
This is not included in the DRC installation instructions.
CRFRALLY50 is quite a hassle to disassemble the Rear blinker.
If you are concerned about this, please confirm that you can remove all the BlinkerUnit from the actual vehicle before ordering and DIY installation.
Connector is too hard to pull out, what's the lock? or "What is the Blinker Vibration Eliminator Bush? If you have any questions, please ask the Shop from the beginning.
I am most afraid of failure in the electrical system.
1:Short and can't tell where it broke.
2:It doesn't work to take it to Shop.
3:Even if you take it with you, it will cost quite a bit of money because you will have to examine it from scratch.
and it is essential to triple the pain.
Tools needed are 8, 10, 12mm Wrench & Spanner, Radio pliers, Nipper, 5mm Hexa, Phillips Screwdriver, Slotted screwdriver (used to remove connector).
I wrote a scary story at the end, but it makes Parenthesis good for more than the price.
It can be very Recommendation. Except for the mud splash... (^^;)
View detail
Fits: KAWASAKI D Tracker 125, KAWASAKI D Tracker X, KAWASAKI KLX125, KAWASAKI KLX150, KAWASAKI KLX250, KAWASAKI KSR110, KAWASAKI Ninja 250, KAWASAKI Ninja 250R, YAMAHA FZ1, YAMAHA FZ1 Feather, YAMAHA FZ6 04-17, YAMAHA FZ6-S Feather, YAMAHA FZ8, YAMAHA MT-01, YAMAHA MT-07, YAMAHA MT-09, YAMAHA TDM900, YAMAHA V-MAX 1680, YAMAHA WR250R, YAMAHA WR250X
Bracket
It is used to replace the Blinker, without which it cannot be attached. View detail
Custom Standard Tail Lamp
[How is it used?
Installed on Yamaha's WR155R.
The Fender Eliminator is installed by removing the existing Tail Lamp...
However, even though the shape was the same at a glance, the screw position was different, and we had to modify it.
Was the one you received as per Image?
The mounting screws are as shown in the Image, except for the Screws and Wiring outlet!
I hadn't thought that far ahead!
Was the installation difficult?
Some processing has been done.
Here's the Fender Eliminator Kit I installed ↓↓.
https://imp.webike.net/article/570988/
The Tail Lamp License Plate Light that originally came with the Fender Eliminator Kit has a bad contact and does not glow or shine.
The construction was also somewhat cheap, so I decided to change it at this time and chose DRC for safety and security.
I thought they must have been made in imitation of DRC because the shape is the same, so I put them side by side.
Like the image, there is something slightly different about the W.
The holes in the bracket were already fixed, so we drilled holes in them.
I tried to install it with some gapping, but I thought it was OK, but now the hole size of the wiring does not fit.
The hole was the same size as the 10mm Drill hole on hand, so I gave up on extending the hole and installed a Nut in between to keep it a little floated. Well, it is not heavy, so it should be sturdy.
The WiringCoupler for the Body and Tail Lamp is also changed to Universal Product.
How was your experience with it?
As expected from the DRC, it is a safe light.
[Included Parts:were they on?
Bullet Terminal, not used this time.
[Was there anything that disappointed you?
No need to say anything since it is a Universal Product! The person who installs the product should do his/her best to make it work.
View detail
Outstanding!
Really good,sturdy build quality and brightness! I used them on my Kawasaki D tracker X. Arrived within a week to Sri Lanka! View detail
Fits: KAWASAKI ER-6N, KAWASAKI Z800, KAWASAKI Z250SL, KAWASAKI Z125 PRO, KAWASAKI Z1000, KAWASAKI VERSYS300, KAWASAKI VERSYS250, KAWASAKI VERSYS650, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI NINJA650, KAWASAKI NINJA1000, KAWASAKI Ninja 400, KAWASAKI VULCAN S, KAWASAKI H2, KAWASAKI NINJA250, KAWASAKI KLR650 08-17, KAWASAKI Z900 17, KAWASAKI Z750 05-06, KAWASAKI Z650 17
Pay attention to the car model and combination parts.
When we converted to a small type blinker, we wanted to install a SMART blinker in the OEM position, but when we removed the OEM blinker, there was a large hole in it, so we could not install it as it was.
At first, we were concerned about how to plug the holes and while doing some research, we found these Parts.
I didn't know such a convenient thing existed! I was impressed.
This is a necessity when installing an external blinker in the OEM position.
This is not a problem with this product, but be aware that depending on the Blinker you replace, the distance from the vehicle body to the BlinkerBody may be shorter.
The Z900 I installed has an ODAX Screen, which is so wide that it hides the inner part of the Blinker just a little.
View detail
DRC Flasher WR250R
Rear blinker was replaced this time.
I like the look and feel of this one.
Holder also has a Quantity:Set is even better.
View detail
Fits: YAMAHA FZ6-S Feather, YAMAHA FZ8, YAMAHA Feather 8, YAMAHA YZF-R6, YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA YZF-R1, YAMAHA XSR900, YAMAHA XSR700, YAMAHA XJ6N, YAMAHA WR250X, YAMAHA XJ6F 09-16, YAMAHA WR250R, YAMAHA TDM900, YAMAHA V-MAX 1680, YAMAHA MT-09, YAMAHA MT-07, YAMAHA MT-01, YAMAHA FZ6 04-17, YAMAHA FZ1 Feather
DRC DRC Flasher holder plate
It is a Level that I would like to have if it were not there, but I would like it to come with the product.
Since it is a part that cannot be seen very much, the color can be any color you like.
View detail
Fits: YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R
DRC DRC MOTO LED Edge aluminum holder kit
Lighter than expected, looks good, and now that the Blinker has been replaced.
I feel like we should change it at this point.
View detail
To the Fender Eliminator in WR.
[How is it used?
Used in conjunction with SRC's Fender Eliminator in WR155
Was the one you received as per Image?
The product was exactly as shown in the Image.
Was the installation difficult?
It was a bit of an adjustment for Universal.
I was able to do it just by scraping.
How was your experience with it?
I have bought it in the past, but it has been versioned up.
The waterproof performance of the wiring root was improved.
[Included Parts:were they on?
Body only.
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: KAWASAKI ER-6N, KAWASAKI Z800, KAWASAKI Z250SL, KAWASAKI Z125 PRO, KAWASAKI Z1000, KAWASAKI VERSYS300, KAWASAKI VERSYS250, KAWASAKI VERSYS650, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI NINJA650, KAWASAKI NINJA1000, KAWASAKI Ninja 400, KAWASAKI VULCAN S, KAWASAKI H2, KAWASAKI NINJA250, KAWASAKI KLR650 08-17, KAWASAKI Z900 17, KAWASAKI Z750 05-06, KAWASAKI Z650 17
Necessities
When installing an external Blinker, it is necessary View detail
Easy to install
I have just purchased a new blinker and replaced the Fender Eliminator Kit at the same time, but the installation of the blinker itself was not so difficult, but the installation to the Fender Eliminator was troublesome. It is my fault that I made a mistake in buying the wrong parts for the front blinker, but the front blinker of the CRF250LMD44 model has a short wiring, so I was very nervous because if it failed, the blinker would go out immediately. The product itself is good. View detail
Screw hole was defective.
Red was out of stock in the Fender Eliminator Kit for my car model. [Color] I bought a Fender Eliminator in Smoke and a Red Tail in Single Item.
The screw hole on the top was too tight to insert the screw, but I was able to fix it with Drill.
View detail