Reviews
Satisfied
I am satisfied with Large because it suits my motorcycle EXACTLY. View detail
Fits: KAWASAKI Z900RSCAFE, KAWASAKI Z900RS, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
the best dress-up item
It's the best dress-up with a long tail. It's a real old z-series look. You can say I did a long tail because of this. No problems with visibility, brightness, etc. View detail
![Z2 Type LED Taillight Set [Exclusive for Fender Eliminator Kit Type II]](https://img.webike-cdn.net/catalogue/images/69679/189-1341_l_TS.jpg)
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Coupler and Bullet Terminal not included
The Harness, Coupler, and Bullet Terminal shown in the product photo are not included in the package. 4 years ago, I purchased the same product from PMC, but about half of the LEDs were not working. The coupler from Tail lamp is an OEM type, and the length of the harness is not long enough because I installed a long tail cowl. I was going to remove the terminal from the Coupler and replace it with the Coupler, but the size of the terminal is completely different, so I cut off the Harness and attached a solder. If the Harness, Coupler, Bullet Terminal, etc. are not included in the package, I think you should replace the picture of the product. If not, I think you should replace the picture of the product. View detail
It's a shame … when it's on.
I would not have bought it if there was a picture of it with the Lens removed. I would not have bought it if there was a picture of the Lens removed. View detail
You should buy it when you find it.
It would be nice if they had them in stock when I wanted them, but they are often out of stock. When I find one, I buy it immediately. View detail
It will look different when the Light area is cleaned up!
It's beautiful, it's good! The look, the Impact, the difference! View detail
Satisfied
Satisfied if not particular about OEM Product! View detail
PMC LED taillight
About quality and texture Great product. Quality as good as the OEM itself About the feeling of use Looks great with the clear case and the O ring light. Products to buy together No other parts needed as I installed on my OEM rear fender. Difficulty of installation Needs about 20 mins to reach the screws just unplugged n plug. Easy to install. Cost performance and comparison with other products Good cost doesn't break the bank. About shipping and packaging Well packed in a box. Any concerns, cautions, or advice when purchasing The braking light may look a bit small. But I think it's sufficient on the road. View detail
Fits: KAWASAKI Z750FX, KAWASAKI Z1000 MkII
Tail lamp lens
It was very nice and very close to the real thing for a reprinted product. View detail
Purchased for CB750four
[How is it used?
Blinker Bracket for CB750four
Was the one you received as per Image?
Yes
Was the installation difficult?
it's simple
How was your experience with it?
Image
[Included Parts:were they on?
Nut, Washers
[Was there anything that disappointed you?
The outer diameter was a little small or there was a clearance on the joint surface with the blinker, so we made the outer diameter larger by using aluminum tape.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Used as an alternative to cb450k0
Since it is almost impossible to pass the inspection with the original one and Valve's procurement is Large strange, we used this one as an alternative that does not spoil the appearance of the old car.
We use only the LensASSY and the light rim is the original one from CB450.
The light intensity is not particularly bright, but it passes vehicle inspections without difficulty, and the light valve can be used with the current standard, making maintenance easier.
One drawback is that the Valve Coupler is installed separately and slightly interferes with the Meter Wire at the back of the unit.
View detail
Too easy to fail.
I had an FXBlinker installed and wanted to change to a Refreshing Blinker. It was a simple job of replacing the bulbs and wiring. When I asked the Motorcycle shop to check the operation, they told me that the aluminum plate holding the bulb in front of the right side had popped out and caused contact. I was stunned at the messy construction.
It is my fault for not checking, but I had no idea it was that easy to build. However, I like the design, so I had it fixed and will use it as is.
View detail
To pass inspection!
Replaced the OEM 350SS for inspection. I was worried if the cat mark would protrude from the optical axis, but it passed without problems!
The H4 socket is not included, so you need to prepare it separately.
View detail
Fits: KAWASAKI Z750FX, KAWASAKI Z1000 MkII
[Color] SmokeTail
[Color] SmokeTail makes Ria look tighter. View detail
Fits: KAWASAKI Z900RSCAFE, KAWASAKI Z900RS, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
"cool
Satisfied with the old car look.
Installed on PMCL Long tail SlightRear Fender with no problems.
Especially if you use SlightRear Fender, you have to transfer and install the NORMAL License Plate Light, but this Tail lamp is integrated with the License Plate Light, so you can remove the NORMALLicense Plate Light. However, since this Tail lamp is integrated with the License Plate Light, the NORMALLicense Plate Light can be removed and refreshed to give a good impression.
The Instruction Manual was available, but it was easier to understand the installation procedure by watching the Manufacturer's YouTube video.
It is easy if you follow the steps.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
doubt
The OEM Tail is cut at an angle, whereas this product is designed to be straight and flat.
If you prefer a modern look, OEM is the one for you.
View detail
The color...
I bought Black, but it was not Black, it was a bit greenish Black. View detail
pretty good
I thought it was fine to have a NORMAL Tail lamp, but I can't see it from me …. But when I was running behind my Z900RS friends, I couldn't help seeing this Abalone Tail! So I replaced it by removing the Tail cowl and the Bracket + ScrewQuantity.:Just remove the 2pcs, remove the power coupler, replace the body, and put it back together! Parts to show everyone how cool your butt is! View detail
No operating noise.
There is no operating noise. It is Relay that chooses the body of the vehicle. View detail
NORMAL is too long …
This is a personal taste, but I replaced the large blinker with a short one because the too long bracket doesn't look like a Race ish.
Quantity with European Blinker:Race ish look with Set
Personally I like it.
View detail