Reviews
Professional customer service
Very nice item, highly recomended. EMS couldn't deliver it to my parcel shop and it was returned to Japan. After a a friendly conversation it was sent again with GLS. It worked this time. Webike has got a really good customer service. Thank you. View detail
Fits: HARLEY-DAVIDSON FXLR DYNA LOWRIDER, HARLEY-DAVIDSON FXSTC SOFTAIL CUSTOM, HARLEY-DAVIDSON XL1200, HARLEY-DAVIDSON SPORTSTER FORTYEIGHT, HONDA VT1100, HONDA VT1100, HONDA valkyrie, HONDA valkyrie, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, KAWASAKI Eliminator 750, HARLEY-DAVIDSON 883, HONDA Shadow Custom, HONDA shadow, HONDA shadow slasher, SUZUKI Desperado X, YAMAHA DS, YAMAHA DSC, YAMAHA Virago XV920
It looks reasonably luxurious, but...
It looks good, but Valve is no good. It ran out in half a day. It is better to prepare it beforehand. Still, for the price, it is satisfactory and a good value for money, so I can recommend it. View detail
Have been looking for it for a long time
Thank you webike for the prompt delivery!
The plastic is a little flimsy otherwise it fits well --------------------------------------- ------------------- Thank you webike for the prompt delivery! The plastic is a bit weak on the same way it fits well Powered by Google Translator
View detail
Fits: KAWASAKI W650, KAWASAKI ZRX400II, KAWASAKI ZR-7/S, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR400, KAWASAKI BALIUS, KAWASAKI BALIUS2
Will not pass inspection.
After installing this Headlight, I went to testCenter to adjust the optical axis.
Two irradiated points, one with a huddled area and the other with a blurry area.
I was told that I could not inspect the car.
View detail
Fits: HONDA jade, HONDA VTR250, HONDA CB-1, HONDA CB400SF, HONDA CB400SF, HONDA CB1000 SF (Big One), HONDA CB1300 SF, HONDA HORNET600, HONDA HORNET900, HONDA HORNET250
Requires modification for installation
There is no waterproofPacking between Lens and Body.
Bulb Socket is not well fixed and is playing rattling around inside.
Some car models require modification to the base of the Blinker mounting area.
I did not install it because I was not sure about its durability.
View detail
Fits: HONDA CB-1, HONDA VTR250, HONDA jade, HONDA HORNET900, HONDA HORNET600, HONDA HORNET250, HONDA CB400SF, HONDA CB1300 SF, HONDA CB400SF, HONDA CB1000 SF (Big One)
Modifications are assumed to be Large.
The first Valve that comes with it is a 5W Wedge bulb even though it is a Blinker.
To replace it with a 21W Single Bulb, a Large modification of the Socket section is required.
There is no WaterproofPacking between Body and Lens.
In the end, it was not installed.
View detail
Fits: HONDA CB750, HONDA CBX250, HONDA NS250, HONDA NS400, HONDA VF400, HONDA Forza(MF10), HONDA fusion, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, SUZUKI DF200, SUZUKI GSX400, SUZUKI RF400, SUZUKI RG400, YAMAHA XZ400, YAMAHA vino, SUZUKI SV1000S, SUZUKI SV1000, KAWASAKI ZZR1200, KAWASAKI ZX-12R, KAWASAKI 1400GTR
I want to cancel an order, but I don't know how.
I want to cancel an order, but I don't know how.
I don't know where to inquire, so I am writing here, even though it is out of place.
I want to Cancel the order before it is shipped, but I am having trouble doing so.
View detail
![A-Screw] LED Blinker Tail Lamp Set](https://global.webike-cdn.net/uiu/impression/202204/15_1020613_625970ab1aede.jpg)
Can be used on the Front side.
Radiator's Quantity:Pair (for Left and Right) Drilled holes in the cover and installed, completing the front and rear LED conversion. Inspired by the original:ACTIVE's LED Front Blinker + Radiator shroud kit for KATANA... Homage... Well, I made it by myself because it doesn't exist for SV650X. I am aware that it meets the safety standard (20 degrees visibility inside), but at your own risk. View detail
Fits: HONDA CB750, HONDA CBX250, HONDA NS250, HONDA NS400, HONDA VF400, HONDA Forza(MF10), HONDA fusion, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, SUZUKI DF200, SUZUKI GSX400, SUZUKI RF400, SUZUKI RG400, YAMAHA XZ400, YAMAHA vino, SUZUKI SV1000S, SUZUKI SV1000, KAWASAKI ZZR1200, KAWASAKI ZX-12R, KAWASAKI 1400GTR
When the weather is nice, I can see it well.
When the weather is nice, I can see it well. It's hard to see when it rains or the weather is bad. I'm using all weather gold now. View detail
Ai-Net Euro front blinker & rear tail unit
Thank you Ai-Net for your euro blinker & rear tail unit. Very nice quality. Clear lens and lights. Matches the mica candy apple red color of my Fusion CN250. Transaction was very good also as with the packaging. Arrived here in the Philippines at expected time. View detail
![[AEBS] LED Blinker Lamp Set](https://img.webike-cdn.net/catalogue/images/29483/61028_01_TS.jpg)
A◯TIVELicense Plate Holder with LED Blinker like this
Installed on a GSX-R1000R 2019
Title
I found it on Amaz◯n, but I didn't expect webike to carry it too.
Unlike the expensive original, it can be made to look similar at a relatively low cost.
Also, if the original Blinker is broken, this may be a good replacement.
(I didn't compare them, so I'm not sure if the Wiring removal and mounting screw positions match.)
The light intensity is sufficient and is visible in daylight.
However, is the directionality strong? If you install the Number in a way that makes it hard to see from the following car.
Wiring is the same as general LED Blinker.
The line is very thin, so you need to be careful not to cut it.
R1000 below (L9) For installation on the
The R1000R is originally an LED Blinker, but if you pimp it, it may become a High flasher.
In fact, when I popped it on, there was no problem while the engine was stopped, but after the engine started, it became a high flasher when the voltage exceeded 14V.
For this reason, it is necessary to put a resistor in the power consumption adjustment.
By the way, my vehicle worked fine if I connected a 30 Ohm resistor.
(Also, the original seems to be a high flasher as well, but the resistor to add is different.)
For your information.
View detail
![A-Screw] LED Blinker Tail Lamp Set](https://global.webike-cdn.net/photo/impression/68/68cec7752c89409c7d5021afb823ed20L.jpg)
Along with the rear fender-less
There is also a smaller LED Blinker, but I thought about the appeal to the following vehicle, and I installed this one which can be refreshed next to the License Plate at a lower price than ACTIVE products while gaining the area of the light emitting part, with the Bracket of Home center (Reflector I installed it with Bracket (Reflector is ACTIVE TYPE 3) and Screws.
Blinker relay is replaced to convert to LED, License Plate Light is still OEM.
View detail
Tough impression of Bates Headlight
I was looking for a Bates Headlight with Light Guard with a tough vibe to customize it to a military look and came across this one.
Black Body and Yellow Lens.
The material is Steel and it is painted Black. The attached Nut and Washer are also BlackPlated.
If you use it for a long time, there is a possibility that Rust will float.
The paint is careful and there is no Wound.
Wiring is Minus, Low and High with Bullet Terminal's Male on each.
It's not a Coupler, but it's not too difficult if you attach the Bullet TerminalFemale to the corresponding cord on the body side.
However, the Net description and the code colors for low and high were reversed.
As for the performance as the important light, the irradiation range is a little narrow and dark impression, but because it is yellow color, it is the range which can be satisfied as a sub-Motorcycle use because the shade comes to the surface.
View detail
Fits: HONDA CB-1, HONDA VTR250, HONDA jade, HONDA HORNET900, HONDA HORNET600, HONDA HORNET250, HONDA CB400SF, HONDA CB1300 SF, HONDA CB400SF, HONDA CB1000 SF (Big One)
I'm glad I bought it
The Blinker Bracket on my 19991 JADE broke off and blew up.
I bought it at the last minute.
The standard of the Cable is different, and it is only OuterCase that I used.
Cable and Valve both used the old one, but it didn't feel any different.
For the price, this was a super bargain for the quality.
View detail
Fits: HONDA CB750, HONDA CBX250, HONDA NS250, HONDA NS400, HONDA VF400, HONDA Forza(MF10), HONDA fusion, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, SUZUKI DF200, SUZUKI GSX400, SUZUKI RF400, SUZUKI RG400, YAMAHA XZ400, YAMAHA vino, SUZUKI SV1000S, SUZUKI SV1000, KAWASAKI ZZR1200, KAWASAKI ZX-12R, KAWASAKI 1400GTR
CB125T JC06
I bought it for the spare of CB125T JC06. It was darker than NORMAL and the optical axis was not clear. Well, it is the feeling that it cannot be helped for the price. When I tried to install it again, the high beam did not light up. Unfortunately, I discarded it. I think it is good to have it for spare because the price is cheap. View detail
Fits: HONDA CB750, HONDA CBX250, HONDA NS250, HONDA NS400, HONDA VF400, HONDA Forza(MF10), HONDA fusion, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, SUZUKI DF200, SUZUKI GSX400, SUZUKI RF400, SUZUKI RG400, YAMAHA XZ400, YAMAHA vino, SUZUKI SV1000S, SUZUKI SV1000, KAWASAKI ZZR1200, KAWASAKI ZX-12R, KAWASAKI 1400GTR
Satisfactory product
Used by Z125PRO
I bought it as a stopgap measure because the Light of OEM was out
There is no difference between OEM and Large so far in terms of usage
I thought about the LED, but the Gold amount is also inexpensive, so I'll use it as is
View detail
Fits: HONDA CB-1, HONDA VTR250, HONDA jade, HONDA HORNET900, HONDA HORNET600, HONDA HORNET250, HONDA CB400SF, HONDA CB1300 SF, HONDA CB400SF, HONDA CB1000 SF (Big One)
You'll be happy with the low price, and it won't hurt!
I checked the texture and strength when it arrived, and I'm satisfied with the price, strength and texture! First of all, the price, Quantity:Pair (for Left and Right) And it's cheap at about $1,000! There is a rubber shock absorber in the body side of the car I'll let it go The texture of the exterior has a BALI, but it comes off easily, so no problem, the internals are crude! Lots of BALI, but it's not visible, so you can remove it with a Cutter Knife and you're good to go Yes, sir! View detail
Fits: YAMAHA XJR400, YAMAHA XJR1300, YAMAHA XJR1200, YAMAHA SRX400, YAMAHA FZR400, YAMAHA FZR250
It's just taking shape
If you're going to buy one, be prepared to process it If you think you can pimp it out, you're wrong
First of all, the Large size of the Wiring Evo-Si is different from the OEM product The inner bracket is different from that of the OEM product, so the bulb is different If it is not, it will not relay
In the end, I used only the Body and machined and installed the OEM internal Bracket
Lens also came off easily just by removing the Screw There is no doubt that water can easily get into it I used a liquid Gasket to deal with this
View detail
Arrived
All perfect order arrived on schedule all as described exceptional thank you I'll be back to make purchases from you good day sale emiliano All perfect order arrived on schedule all as described exceptional thank you I will come back to make purchases from you good day sale emiliano translated by Google Translator View detail
I could not use it at all
Purchase expecting from COSPA. Although the apparent appearance was good, the accuracy of the shape was bad, and if it could be used if processed it was not Yu substitute. I thought it was just Valve but it was not possible to wake up High flasher. View detail