Reviews
It was worth the price.
I was a little disappointed because it was an Image that glowed a little brighter.
Well, I can barely see Meter, so I'm going to use it as is for now.
View detail
![Z2 Type LED Taillight Set [Exclusive for Fender Eliminator Kit Type II]](https://img.webike-cdn.net/catalogue/images/69679/189-1341_l_TS.jpg)
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Coupler and Bullet Terminal not included
The Harness, Coupler, and Bullet Terminal shown in the product photo are not included in the package. 4 years ago, I purchased the same product from PMC, but about half of the LEDs were not working. The coupler from Tail lamp is an OEM type, and the length of the harness is not long enough because I installed a long tail cowl. I was going to remove the terminal from the Coupler and replace it with the Coupler, but the size of the terminal is completely different, so I cut off the Harness and attached a solder. If the Harness, Coupler, Bullet Terminal, etc. are not included in the package, I think you should replace the picture of the product. If not, I think you should replace the picture of the product. View detail
It's a shame … when it's on.
I would not have bought it if there was a picture of it with the Lens removed. I would not have bought it if there was a picture of the Lens removed. View detail
PCX125JK05
Front suspension of PCX125JK05 is Quantity:Pair (for Left and Right) The size or rather the shape is different in
So Quantity:Pair (for Left and Right) I don't remember which one, but it doesn't go on straight away, so a lot of ingenuity is required.
It was scratched or the paint peeled off.
Rubber sheets for protection, such as double-sided tape, should also be prepared.
I have no problem with the sturdiness of the product or anything like that.
It would be nice if there was a dedicated Bracket, but there is not.
I wonder if it will be attached if Type is made into 44 pie.
View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
subtle
Perhaps it is because the Scooter has a low power generation rate, but I feel that the Halogen bulb has a wider beam range and better visibility.
This might be better with a slightly better Halogen bulb.
View detail
Fits: KAWASAKI 650RS, KAWASAKI 650-W1, KAWASAKI 250SS, KAWASAKI 250SS, KAWASAKI 250SS, KAWASAKI 250SS, KAWASAKI 350SS, KAWASAKI 400SS, KAWASAKI 400SS, KAWASAKI 500SS, KAWASAKI 500SS, KAWASAKI 500SS, KAWASAKI 750SS, KAWASAKI 750SS, KAWASAKI KH250, KAWASAKI KH400, KAWASAKI KH500, KAWASAKI Z2, KAWASAKI Z1, KAWASAKI KH250
We can only be thankful that we have Parts….
It functions as a Blinker Bracket.
The shape is completely different from that of the OEMBracket.
That's the fate of Ripro products, we should be thankful that Parts is sold.
We do not recommend this product for the finicky or nervous person.
View detail
Fits: HONDA little cub, HONDA Super Cub 50, HONDA Super Cub STD-92 (12V model), HONDA Super Cub STD-92 (12V model)
Don't expect quality.
I had a headlight unit from another company attached to my LITTLE CUB, but after more than 10 years of use, the plating was peeling, so I replaced it.
The installation itself was not a problem, but the Socket does not seem to be durable.
I installed it at the end of September 2023 and from the beginning of December 2023 the Headlight started flickering occasionally and a few days later the Headlight disappeared while driving and became completely unusable.
I suspected that the Valve was out of ballast and tried to remove it, but for some reason it would not come off. When I pulled it out by forcibly turning it with pliers, I found that the Socket had melted. The melted valve had lost contact with the valve, and the resin was further burnt.
Since the price is reasonable, I think it would be better to use OEM products like Large for Socket and Valve, with Socket and Valve as extras.
View detail
Fits: その他 12V car
dark
The Front as well as the Rear are dark.
It is actually rated ??1, but I changed it to ??2 to account for the fact that it is being changed to a Smoked lens.
View detail
Fits: SHERCO SM 50 R, SHERCO SM 50 FACTORY, SHERCO SM 50 EROIK, SHERCO SM 50, SHERCO SM 5.1 I-F, SHERCO SM 4.5 I-F, SHERCO SE 50 R, SHERCO SE 50 FACTORY, SHERCO SE 50, SHERCO SE 4.5 I-F FACTORY, SHERCO SE 4.5 I-F, RIEJU RS3 50 PRO, RIEJU RS3 50 NKD, RIEJU RS3 50, RIEJU RS2 50 MATRIX PRO, RIEJU MRT 50 SM PRO, RIEJU MRT 50, MBK X-LIMIT SUPERMOTARD, MBK X-LIMIT ENDURO, GASGAS WILD HP 450
It's just OEM style.
It claims to be OEM compatible, but it's just a look. it's an off-road vehicle blinker, so it needs to be flexible, but it's a cutchica. If it rolls over, it will break in one shot.
Still, we are grateful that they are making these parts when OEMs are no longer available.
Moreover, WeBig has been very helpful in handling even Minor car models.
View detail
Both High low of Type 2 GSX1300R HAYABUSA are replaced.
Previous Spec. is NORMAL for High beam.
Low beam is HID55W made by 88House.
The high beam was too dark to pass the inspection, so we replaced both the high and low beams with LEDs.
result
The high beam passed the inspection with ease, but the low beam is too dark to drive at night.
I think it is brighter than NORMAL, but I felt it was too dark for my experience with HID 55W.
In the near future, we will switch back to HID only for Low beam.
View detail
Fits: HONDA Dunk, HONDA Sh mode, HONDA Giorno, HONDA BENLY50, HONDA CROSS CUB, HONDA BENLY50110, HONDA DIO110, HONDA glom, HONDA FORZASi, YAMAHA VOX, YAMAHA VOXDELUXE, YAMAHA VOXLIMITED, YAMAHA GEAR, YAMAHA NEWS GEAR, YAMAHA VINO, YAMAHA VINODX, YAMAHA VINOMolar feh, YAMAHA SDR, YAMAHA MAJESTY, YAMAHA MAJESTYC
The LED light bulb brightness and projection angle
I bought two M&H Matsushima led headlight bulbs for my 2014 HONDA MSX125 and got them installed. The brightness is less than that of OEM bulb. Horizontal projection angle is not wide enough, so I got back to the OEM bulb. Sorry. I do not recommend this bulb and gives two stars for the overall rating. View detail
Fits: その他 12V car
It's dark
Not enough illumination. From a fellow who went Touring with me. "can not see" It was pointed out to me that this is not a problem at night. I think it is fine at night, but in good weather during the daytime, visibility is insufficient. I have a Blinker lens. [Color] I think some of them are in Smoke, so I decided to use ??2. By the way, the Right Side of the image is our product. I thought it was dangerous, so I bought brighter LEDs. (Left Side) View detail
So bad
Since it is a Type that covers OEMTail, it was totally useless if the Tail is changed, because the shape is different.
Of course, it is my mistake, not the product's.
View detail
It needs to be processed.
The description is such that it can be used as is with Couplet-on, but those who want to make it OEMSpec. will need processing and additional parts.
The item I received is missing the Wiring on the Headlight and has a hole in the lid behind the Valve.
The lid behind the valve is also too tight to turn, so it needs to be modified to enlarge the hole.
Maybe this product is for LED Headlight sold in Ariake etc.
I asked Webig in advance and received an answer that the product was JapanSpec. light, but the product I received was such a troublesome product that required one or two steps.
Please note for future purchasers.
View detail
Durability concerns?
Used in CUB press 50.
It is very bright due to the fact that it is LED. When I first bought it, I thought it was a very good buy.
However, about two weeks after purchase, it finally stopped lighting up with symptoms like poor contact.
I'm wondering if the vibration caused the damage.
I purchased the LEDs with the expectation that they would last for a long time, but they stopped working in a shorter period of time than expected.
I can say that it would have been a good purchase if it had been used for a long time, but the period of use was too short to say it was good.
I think the price is not very cheap product, so I expect improvement in durability.
View detail
It is a bit long, so it may not be possible to attach it to some car models.
I asked for a short case, but it didn't fit in the headlight case. View detail
We will be reverting back to OEM.
When replacing the OEMHeadlight, the Light is too small and all the Wiring that was originally in the OEMLight is now out of the Light.
I asked my favorite motorcycle shop to install it, but they couldn't help me. The handlebar area was too messy.
Design is very Parenthesis, so if you still like it, I recommend this product!
View detail
Not bright.
Blinker on moped is now LED.
The brightness was dimmer than the bulbs and did not make sense.
However, the power consumption became smaller, so I think it was effective there.
View detail
Not well made for over 30,000.
Because it is quite large, it hits with the front carrier attached, hits the OEM meter, and is not considered to be Clearance.
Front carrier was removed, OEM meter was installed and bracket angle was modified to secure clarity, but only bolts on both sides were fixed and optical axis shifted while driving.
The enclosed Washer and RubberWasher are also used together to make it a little better.
The nut inside the light is also in a free state, so the light is aligned with the optical axis, the light is removed, and the bolt is tightened.
If it is nut welded to the inner plate. and if it has a separate Bracket for optical axis adjustment.
The light and back boxes are not like the OEM ones, and there are gaps between them.
It is brighter, but 38,000 yen for this?
Fog Lamp from another Manufacturer is recommended.
I went Camping touring the other day and no one was wearing it. I'm convinced.
View detail
I liked the way it looked.
It broke after a little over a year.
I thought I had accidentally pulled a HaGap, but was surprised to see the same Review.
It's a shame because it looked great.
View detail