Reviews
Part of expendable items
【What made you decide the purchase?】
With the removal of OEMRear Fender, when reusing OEMBlinker and attaching it to a vehicle, it covered the Silencer exit and the Blinker melts due to the heat of exhaust gas, so the shape is close to OEMBlinker with Small type and the Blinker base is Flexible type I wanted Blinker and purchased it.
【How was it actually used?】
Although it is not LED, after all Blinker felt that the sphere had better visibility. The feeling attached to the vehicle was not bad, Blinker was Small, so it was possible to prevent touching the road surface even when it falls over. Also, even if an obstacle collides with Blinker, since Blinker's root is made of Rubber, it can be folded. Furthermore, in the case of bulb burning, it is easy to replace spheres, there is no exchange of Blinker itself, so it is great to change the Large.
【Was it difficult to install? (Hard parts case)】
Adjusting the Large size of Washer, it can correspond to various mounting diameters.
【Please tell me the point of installation and hang (in the case of Hard parts)】
When installing Blinker too much, if you tighten too strongly too much, the Rubber of the vehicle attachment part collapses and deforms and the Blinker itself bends, so there is no problem if you use moderate tightening loosening prevention agent. Also, there is processing of Wiring, so if you are not confident about Wiring of the vehicle do not overdo it, let's ask the store.
[Is there anything I was disappointed about?]
In the case of bulb out, we do not sell 8 w balls, so it is stupid to eventually replace the Blinker itself. By chance, my vehicle was OEM, so I did not exchange the Relay but purchased Wedge Ball 10 w separately and attached it to the Blinker, but the 10 wedge got 2 mm Large from 8 w, the top lid became hard to tighten However, it can be used without problems.
【Hope for Manufacturer - Please let me know if you have any improvement points]
8w For mounting on a vehicle, you can not buy a replacement ball once the ball has run out. If you install 10w, you can not use without replacing the Relay, so please make it 8w 10w Wedge sphere dimensionable so that it can be used without problems.
【Have you compared items?】
There will. This site's Blinker, but exactly the same Spec. I am using 8 w Wedge balls.
View detail
LED is also good - - -
【What made you decide the purchase?】
Because it was resistant to vibration, making it resistant to deformation.
【How was it actually used?】
It is really strong against vibration, even if Blinker itself bends it will not break at all.
LED Blinker is also good, but after all the brightness of the ball is shining with a warm feeling.
Also, even if the ball went out of spite, it is enough to change the sphere, so it is easy and good for those who use vehicles like me.
If it is an LED, it will be replaced exactly like Blinker.
【Was it difficult to install? (Hard parts case)】
Anyone can install it with knowledge of Wiring.
【Please tell me the point of installation and hang (in the case of Hard parts)】
Bullet Terminal is used for joining with the body side Wiring, but since the Bullet Terminal was an unstable connection method, separate Motorcycle ManufacturerOEMfor Blinker Coupler is installed and it is easy to do work at the time of replacement and secure connection I made a little effort to do it.
Also, since Bolt connecting the body side and Body is not included, a separate 6 MM Bolt nut is required.
When installing, if you tighten too much Bolt, the root of Blinker will be deformed, Blinker will face a strange direction, so please be careful of over tightening.
[Is there anything I was disappointed about?]
Since the car body side was 10 W Blinker, this product Blinker was 8 W - I raised a high flasher, but once I exchanged the ball for 10 w of Wedge I was able to resolve it.
Barely 10 W of Wedge can be worn.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Why? Wedge ball 8 w is not made of balls that can not be purchased? Even if the ball breaks out, 8 w is not Wedge, so the Manufacturer side wants to purchase the Blinker itself again and sells it?
From the beginning, please make with a 10 w ball.
【Have you compared items?】
There will. It is a similar Blinker of Wee Big.
As well as here, because we are using a 8w ball not on sale, it is the last if the bulb is out.
[Others] Any item
View detail
KTM vehicles to High flasher
When installing on KTM vehicles will be High flasher.
OEMBlinker bulb is 12V 10W.
Since this Blinker bulb is 12 V 8 W, please be careful because it becomes High flasher when installing.
Wedge sphere is a replacement type, so when I purchased Wedge ball of T1312V10W for testing I did not get awesome high flasher.
In T13, the Wedge ball is slightly large, but I was able to install it barely, so I tried to replace Relay, but I could avoid it with the Wedge ball.
Those who raised High flasher with this product, Wedge Ball (T10 - T13), so it's worth a try before replacing Relay.
View detail
Seismic impact shock Blinker
【What made you decide the purchase?】
Because I wanted to exchange one's side of the vehicle, I searched for a shock-resistant, shock-resistant FLEX Blinker in Coloring's Blinker similar to the vehicle OEMBlinker and it arrived at this Blinker.
Also, because it is a Light Bulb Type, I was looking for a shape that was easy to replace when the ball was exhausted.
【How was it actually used?】
Size is also smaller than OEMBlinker, it is very satisfied without interference with Silencer. Also, even during off road traveling, since Blinker Nemoto is made of Rubber, she is able to escape the tremor well.
【Was it difficult to install? (Hard parts case)】
For installation, if the diameter of the Blinker installation hole on the vehicle body side is 8 mm, since the Blinker side is 6 mm, it may be necessary to process and attach it with Color, Washer, etc..
【Please tell me the point of installation and hang (in the case of Hard parts)】 In addition to Blinker, 6 mm BoltNut, Washer is required for installation. It is not attached to the product. Also, for processing the Blinker attachment part, Drilletc. In some cases it may become necessary, so if you install it yourself, a tool is also required. Furthermore, since it is also necessary to process the power Wiring when mounting on the car body, those who do not have confidence in Bullet Terminal, Crimp work, those who do not have Electric Works Pliers, obediently asking the shop to work, Extra expense can be suppressed.
[Is there anything I was disappointed about?]
Although it is Wiring of Blinker, the most soft clothing Wiring (Midline) So, I am worried about aged deterioration. Wiring folding etc.. I think that if you do not do it too often you can prevent the Wiring rupture.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I would like you to raise the strength of Wiring. I would like you to raise the intensity of Nemoto Rubber a little more and I would like you to make the base shape a bit thicker.
[Others]
Those who ride in a vehicle with a vehicle inspection will think that Light Bulb TypeBlinker here is more reliable than LED Blinker. As it is LED Type at the time of inspection, I will not go through the vehicle inspection even if only one ball is blown, so I think whether Light Bulb Type will make it easy for the ball to cut out. Also, with LED Type Blinker, since every Blinker will be replaced at the time of failure of the foundation,. Well, I think that Light Bulb Type is still easy.
View detail
Whether there is a problem in function
I think whether there is a problem in function. Blinker root is also made of rigid Rubber, falling over - I think that it is a structure that can withstand vibration.
However - - - Unfortunately the installation Bolt - I am sorry that this is because Nut is not included.
View detail
Off-road Car Destinations Blinker
If you play mountain with an off-road car, you fall off with a high probability. Moreover, the overhanging Rear blinker will be damaged. Before that happens, it is necessary to replace the Small Type Blinker in advance. As this product is made of rigid Rubber, it is very tough! Wiring also has Bullet Terminal processed, so it's easy to install! I want to install it, I think I wanted the attached Bolt to be attached.
View detail
It attached to the TRIAL vehicle of Touring-Trial specification. If a 5-mm Bolt hole is made and attached to the right and left of a ACERBIS X-LED PLATE Tail light, the safety standard is suited at 15 cm width on either side. It is likely to be hard
It attached to the TRIAL vehicle of Touring-Trial specification.
If a 5-mm Bolt hole is made and attached to the right and left of a
ACERBIS X-LED PLATE Tail light, the safety standard is suited at 15 cm width on either side.
It is likely to be hard to break in a
small light weight, and is tight on a TRIAL vehicle.
Very much satisfied.
View detail