Reviews
![[Mr Quick] Turn Signal Garnish](https://img.webike-cdn.net/catalogue/images/132007/mr19-cc07-01_TS.jpg)
Easily Black Spec.
[How is it used?
Street riding.
Was the one you received as per Image?
It is not so bad, but not so bad.
Was the installation difficult?
Just remove one Screw and insert it.
How was your experience with it?
Blinker's Plating was a bad girl and I was concerned about it, but here it all went away.
[Was there anything that disappointed you?
Roughness of the manufacturing process. BALI removal and file hanging are essential before installation because of the great BALI.
Other items that would be helpful
Availability and clarity of Instruction Manual
No Instruction Manual.
Opinions and requests to Manufacturer
I would like to see you at least take BALI.
View detail
Tail Bulb replacement for KSR's Fender Eliminator Kit
I purchased a used KSR80, but the previous owner installed a Fender Eliminator Kit, and the tail lamp is a Lucas type.
There was a Trouble with Tail Bulb immediately after purchase.
I removed the Lens to see the model of the Lamp to replace it, but unlike the usual Double Bulb, the head was a Small Rhinoceros Bulb.
This Type was not sold at Home center or Car Shop 。 Maybe MotorcycleParts specialty stores have them, but I can't find any near me. 。
However, because the length of the Tail Bulb was different, it interfered with the Lens, causing the Lens to chip, melt, and consume more power due to its higher wattage.
I had put it off because it was inexpensive but the shipping and other things made it needlessly expensive, but I had some shopping to do at WeBig, so I bought it as a package deal.
After installation, there was no interference (obviously), and since the Watt number was lowered, the power consumption was also lowered, eliminating the concern factor.
I am planning to eventually switch to LEDs, but there is a barrier of full-wave rectification, so I may end up putting it off.
View detail
Beautiful lights
The lights feel and look beautiful and visibility is improved!
As for the price, I personally think it would have been easier to afford if it were a little cheaper.
View detail
Favorite Large size difference
I am in love with this Size! I am so glad I bought it! View detail
Satisfied
I am satisfied with Large because it suits my motorcycle EXACTLY. View detail
Fits: HONDA CB1300 SUPER BOL D'OR, HONDA CB1300 Super Four, HONDA CB400 SUPER BOL D'OR, HONDA CB400 SUPER FOUR
Posh LED taillight
The taillight arrived within a week of ordering which is great, the fitting was straight forward using all the original brackets and screws,the plug was a direct fit to the original connector,great product very happy. View detail
It was an initial defect.
When I tried to install it immediately after receiving it, it was blinking ChicaChica and I could not use it. I thought my motorcycle was bad, so I ordered another product from Amazon and installed it and it lit up without incident. I would like to return it as soon as possible, but I have not received any response from Webig! Amazon is much more reliable. View detail
failed to pass inspection
Less than one year after replacement, some of the bulbs went out and the Stop became non-lighting.
Although I thought it was faintly on the day before the inspection, it was not lit on the inspection line.
Even if we can discount it to individual differences, the quality control is so poor that we will refrain from using the same Manufacture's products in the future.
View detail
Japanese Vehicle Inspection Correspondence
Before the inspection of SR400, I went to the tester place off site to check the light intensity. I had to go back and forth to Tester two years ago, but they did it without any extra charge, I switched to the new Stanley Hyper Halogen LightValve, which I brought with me again. It is just 150mm away from the specified light level, but it is OK.... Hyper Halogen Light is a high efficiency valve and can be brighter with the same power consumption as the standard valve, but it seems to have a shorter life. View detail
It is easy to install.!
OEMHalogen was replaced because it was too dark.
Installation is a simple matter of removing and replacing the OEM. I did a test run during the daytime, and it was a little brighter in the Tunnel. I don't drive much at night, so no problem! I don't drive much at night, so no problem! I don't know about durability, but I'm happy with JAPAN, it's well made and looks good.
View detail
Fits: BMW HP4, BMW S1000R, BMW S1000RR
Appeal full score
Installation is very easy. No modification, no drilling, nothing at all. 3Pattern Stop-lamp and 3Pattern Blinker are available for your enjoyment. The instruction manual was not included, but it is clearly explained in the video, so I had no trouble. I am satisfied with my purchase of Large. It is cool. View detail
Bright!
The OEM was dark, so we replaced it with a new one and the custom feel is improved.
[Color] I chose Smoke and it is not too Black.
View detail
There is a sense of security dedicated to the car model.
DL1000 V-STROM650XT ('22) The product has been installed in a
It will be used in conjunction with Hepco&Becker's Engine Guard,
The bracket of the Radiator part was a little bit hit by the Guard,
The installation was only a little difficult, but it was almost interference-free. I think there may be individual differences, so this is just for reference.
Because the connection between the Fog Lamp and the included Harness was a Flat Terminal,
We changed to WaterproofCoupler just in case.
The brightness is sufficient for an auxiliary light,
Cutline is also solid, so I don't think it will bother oncoming traffic.
Considering the price, the texture might be a bit lacking,
If you are concerned about this, you should consider another product.
View detail
Fits: YAMAHA
Seems a little high.
Feels a little unstable in the mounting position View detail
Was good
The product arrived quickly because I was out of bulbs. View detail
A quality low-profile blinker kit
The kit I purchased was well packaged and tailored for installation on a V-Strom 650. All parts appear to be good quality and ready for immediate installation on the bike. The kit includes wiring adapters to suit the bike (bullet connector to 2-pin Suzuki connector) and a new 7-pin LED blinker relay. Installation was easy for someone with moderate experience. Tools required: open-end wrenches (8~12mm), hex key wrenches (4~5mm), 10~12mm socket. The rear fender of the bike must be removed to access the wiring and remove the existing blinkers. Routing the wiring through the adapter plates, washer and nut requires patience and a delicate touch. Aside from that, it's a matter of securing connections with electrical tape and securing the wiring to the frame. The kit is quite bright and very visible, even during the daytime. The blinkers are all mounted on flexible stalks, so they should survive if the bike is dropped. Overall, I am very pleased with the purchase. View detail
The price is ….
It looks cool, but as with all RS parts, the price is too high! View detail
They say it's good if it lasts 5 years.
After five years, it broke. When I removed it, the yellow-colored luminous body was shattered and the base was burnt to brown. The light suddenly faded and became like a miniature light bulb and disappeared. I was surprised because I happened to be watching it. It would have been extremely scary if I had been driving at night.
When I bought it, the yellow colored tip was not square and the corners looked peeled off in places. I asked the ManufacturerStaff if the Large tip was sturdy, but they said it was fine, so I had it installed.
Well, it would be impossible because it looks like the LED light-emitting base part is burnt out.
As for the product review, at 6000k.
It is not brighter than OEM, but the color is White, so some scenes actually look darker. It is still not as good as the most powerful HeadlightHID, but it looks better than the OEM Halogen when compared to rural roads and other places without streetlights. 。
However, in urban, city, suburban, and highway areas where there are some lights, the white LEDs are covered by the lights and it is difficult to tell whether the light is illuminating or not.
If the Type is one light on low and two lights on high, I would recommend changing the color temperature with low high.
This time I did the work myself, but when I first bought it, I was told that it would wait 20,000 hours or 10 years if it didn't break, but in fact it was 5 years, so I felt like I lost money, but that seems to be the way it is.
It is good that they are cheaper now because of the New Model, but I wish they would have stopped reducing the warranty to 2 years if they continue to claim that they can be used for a long time.
Now, how to do the work
This time, I performed the work myself, copying the way SphereLight's ManufacturerStaff actually did it on my Motorcycle.
As mentioned in the postscript, the way this Rubber fits (How to put it out?) If this is the case, the heat sink portion will be buried in the rubber, so I am concerned about whether the heat dissipation will be large enough to withstand the heat.
Turn the round cover of the OEM Headlight unit counterclockwise about 1 cm to remove it.
Remove the valve spring and remove the light valve.
Remove the Attachment from the Valve of the product and insert the removed Attachment into the place where the Headlight Bulb was inserted, with the four notches facing backward, and fasten it with the Spring.
At this point, you should install the Valve once in the Attachment and remember the feeling of pushing and turning it to install.
Attach the supplied CouplerConnector to the product as described in B of the Instruction Manual.
Connectors on the body side and the Light side are connected.
...At this point, conduct a lighting test.
The space inside the Headlight unit is quite large when you put your finger inside, so leave about 15cm of Wiring and put all Connectors and Controllers inside the Unit. (I put almost all of them in Space under Unit)
Note that if the wiring connected to the light is about 10 cm, the light valve will stick when the cover is attached and will not be able to be pierced.
If the controller rattles inside the headlight unit, use the Tie Band to hold the controller in place. I don't do it.
Once this is done, it is time to install the rubber cover, which is the most difficult part.
It takes several hours at worst, and although it is easy to install if the Rubber is heated considerably, it is not recommended because deformation is a concern.
The difficulty level increases because everything is put into the Unit.
Push the outer frame of the Rubber cover into the Unit.
At that time, the side that is folded should be toward the rear of the vehicle.
When you push it in, there are three indentations where the OEM's round cover fits.
Make sure three Folds are outside the Unit, then install the LED Bulb.
(Note that if you push the Rubber as hard as you can, only one Fold will come out backward.)
(The outer frame of the rubber cover of the type after the warranty period of 2 years is larger than that of the type before that, so it should be installed in a larger size.)
LED Bulb is perpendicular to the ground when installed.:Pair (for Left and Right) to be facing the
If the remaining wiring seems long, push it in a little at a time.
The above work was completed without making any cuts.
ManufacturerStaff had done this and it was a work procedure that worked fine.
However, if the rubber is pushed out this far, the heat sink will be buried in the rubber, so I wonder if the heat dissipation is Large sturdy. I wonder,
I had done it this way before, so I copied it as it was.
View detail
Lack of good product Level is low.
Used on a SEA BASS VST 650. I tried riding at night with it on, but it was dark. It is just too dark. Also, the optical axis is a little bit off. So, when I adjust it to the lower side, the difference of optical axis between high beam and low beam is very different. PIAA or Ray Brick (Stanley) I would not recommend purchasing anything other than the 2-wheel dedicated LEDs from I think the next best choice would be SYGN HOUSE. By the way, I have purchased SYGN HOUSE twice in the past, but the low beam ran out after about 1.5 years. I hope this will help you in your purchase. View detail
Nice touch!
The Tail is much brighter and I am happy with it! View detail