Reviews
Solder failure
Blinker signal line Solder defective
Since it was purchased new, I assumed there were no initial defects, so I removed the tank and inspected the wiring extensively.
I'd really like to charge the actual cost.
View detail
Fits: YAMAHA DRAGSTAR400(Later model 5KP) DRAGSTAR400 CLASSIC(Later model 5KP)
It is easy to install.
I bought it because I had to change my Speedometer from electric to mechanical due to the age of the tank.
At first, I thought it would be a painstaking process, but the Instruction Manual was easy to understand, so it was much easier than I expected.
Grease was not included, so you may want to have it ready.
View detail
Fits: YAMAHA Dragster 400 Classic, YAMAHA Dragster 400, YAMAHA Dragster 400 Classic, YAMAHA Dragster 400
It is a good product, just as I expected.
It is a good product, just as I expected, and the length was perfect.
The rest is durability, but considering the price, I am satisfied.
View detail
Fits: YAMAHA Virago 250 (XV250), YAMAHA Virago 250 (XV250)
It doesn't work
It is xv250, but you will need a further extension cord to use this.
VIRAGO250 requires a length of about 95mm, which, if you look closely, is listed as 700mm 。 More than 200mm short. 。 I am sure the Shop is not at fault because I made a mistake in checking the length, but if you believe it and cut the seal, returns will not be accepted, so I suggest that you always check the length before ordering.
View detail
Satisfied with Cospa
There are quite a few bad reviews, but I've been able to use my product without any problems.
I've been using it for a year and a half on a RigidXL1200C SPORTSTER 1200 with a lot of vibration, and it's been in service without breaking.
View detail
Not installed yet, but I'm happy with it
I can't find an indicator for SR400's Initial Model, so here it is I bought it
I'm glad I bought this product as I'm not installed yet but I'm happy with the look and feel of the product
The installation itself is not that difficult
View detail
Fits: YAMAHA Virago 250 (XV250), YAMAHA Virago 250 (XV250)
Was good
Purchased to install a voltmeter on my VIRAGO 250 The shape and mounting points are satisfactory The shape and mounting points are satisfactory, but it would have been better if there was a plating as well, as it is only available in black View detail
Indicator Lamp
I ordered one set Indicator Lamp (Triple) & Mounting Bracket that type standard from GARAGE T＆F because it is cheaper than some of the same type. It's more beautiful than I thought and I feel satisfied View detail
Fits: YAMAHA Virago 250 (XV250), YAMAHA Virago 250 (XV250)
So so
It looks nice, but a bit expensive
I was with instructions for once.
I think that it is possible to do with the same amount of gold even if it makes it properly at Home center with Bracket or Angle.
View detail
Be careful of overtightening
I bought it to install DAYTONA's Tachometer to ELIMINATOR 250V. Inch handle Bracket is currently out of print DAYTONA, so here. Because it is a Universal Bracket, Meter will shake, but if you tighten it too fast it will be hard for Bolt to bend and remove it, so be careful when tightening. View detail
I have to work while confirming without worrying about manuals
Price and appearance were as expected as expected.
It was uneasy because the number of usable Meter φ is unknown.
It is Size that can be used with DAYTONA 60φ.
Red - Green - There was Yellow color Lamp, except for Yellow color was opposite to Instruction Manual.
It took me some time to rewiring it again, but now I can use it.
"There are cases where there is a case reverse to the manual depending on the lot" It was written, but with the normal one
Because the opposite thing is mixed, the person who is purchased from now is Plus - Minus
Even just check it and you should do installation.
View detail
Low Quality
Buy Ring Type that was previously in DAYTONA out of print.
But anyway the quality is poor, fixation of LEDCase and Wiring is graze on adhesive glue, abrasive is mixed in Screw hole of Ring, it does not run smoothly as it bite the thread, the Lens of Green Light is full of Wound (I do not know if I do not let it light up) Quality is not a talk in.
Because LEDCase and Wiring are full of gaps, Waterproof nature is not as bad as
Recommendation It is not a product that can be done.
View detail
Fits: YAMAHA Virago 250 (XV250), YAMAHA Virago 250 (XV250)
Easy to install
With this, you can easily move Meter out. It's really easy to install and you can also do anything with a manual as well. Afterwards it is done just by tapping Meter's Wiring a little.
It is recommended because the look around Handlebar looks neat.
View detail
Received the cable after 10 days. In very good condition as expected. But the cable is only 700mm in length so I cannot use it on my SR400. It can only be used with lowered bike or a bike with aftermarket speedometer fixed below the triple-three. As a
Received the cable after 10 days. In very good condition as expected. But the cable is only 700mm in length so I cannot use it on my SR400. It can only be used with lowered bike or a bike with aftermarket speedometer fixed below the triple-three. As a result I had to order the new and original speedometer cable (880mm in length). Hassle free shopping at webike and I live in Malaysia. Will continue shopping with webike. Thanks! View detail
The paint was peeling off ...
As soon as it arrives, if you check the spot things, you found something that Garbage might have adhered, and when you casually touched it was a paint stripping ...
Because the paint itself was Beauty, it may have been defatted insufficient just before painting there ... I painted it with oily Magic and made it fake (Lol)
The installation was attached to DAYTONA's Speedometer. It is Φ 60. By the way, this is not exclusive to the car model. It is a Universal Product. Let's prepare Wiring diagram and Coupler etc. separately.
After mounting it was black and the shape also fell well and the matter of painting was disappointing.
View detail
Attached to SR 400 Initial Model!
I installed it in the Initial Model Disc brake SR400 vehicle.
By Custom, I bought the Speedometer next to Tank, so I was looking for a Short Type Speedometer Cable.
Since the conforming vehicle was SR400 Disc brake car,
Although there was also anxiety, it was able to fit in Initial Model vehicles without problems.
With this, the surroundings of Wiring are refreshing.
View detail
GarageT&F Indicator Lamp (3 stations) & Mounting Bracket
Because OEMMeter was broken, it was attached to Posh made Mini tachometer. While looking at the Wiring diagram of Service manual, I processed Bullet Terminal to OEM Indicator Wiring and connected it, but it is quite a painful work. I do not want to bother because I like troubles, but people who dislike it may be better to go to Motorcycle shop.
View detail
Fits: YAMAHA DRAGSTAR400 CLASSIC, YAMAHA DRAGSTAR400
An inexpensive way of lengthening your speedometer cable with out having to buy a brand new one. Simply screws into your existing cable and allows you to fit onto that new custom handle bar you may have purchased.
An inexpensive way of lengthening your speedometer cable with out having to buy a brand new one. Simply screws into your existing cable and allows you to fit onto that new custom handle bar you may have purchased. View detail
Fits perfect in my XBR500!! Fast shipping, well packed, is not yet installed but seems good quality and easy installation.
Fits perfect in my XBR500!! Fast shipping, well packed, is not yet installed but seems good quality and easy installation. View detail