Reviews
ODBAdapter
Connect to SMART phone to see Motorcycle information. RPM, etc. View detail
Fits: YAMAHA Cygnus Gryphus, HONDA CRF1100L Africa Twin, HONDA CBR400R, HONDA 400X, HONDA Rebel300, HONDA CBR500R, HONDA CB500X, Others , SUZUKI DL1000 V-STROM1050, KAWASAKI NINJAZX-25R, KAWASAKI NINJA1000SX, HONDA REBEL250
GSX1300R HAYABUSA's OilReset is the motive for purchasing the GSX1300R HAYABUSA.
New Model GSX1300R HAYABUSA has been over 1000km and I felt stress in Sir Bustier's Mark and Spanner's Mark and tried to reset it, but… there is a strong person who is resetting it by his own wiring in a certain site. I bought this one because it is a very thin terminal and it seems to be bent even if I make it.
When I checked the delivered product, I found it to be of good quality. I immediately checked the continuity of the terminals for OilReset with a tester, and found that the number 4 to 5 Earth." So, number 9 is. OilReset (Service?)." Terminal and confirmation of
From Key Off, connect this Tool to OBD with the matching terminal, and from Key On, connect the Tool to OBD with the matching terminal. SET." From long press SERVISE. from the next Oil replacement distance. and OilReset to finish the Refreshing!
Recently, OBDTools have become inexpensive, so if you can find one that fits your needs, it would be no problem to have it to check the condition of your vehicle.
It is a recommendation tool for Riders who can do DIY oil change!
View detail
Fits: YAMAHA CYGNUS Gryphus, YAMAHA Bolt, YAMAHA GEAR, YAMAHA XG250 TRICKER, YAMAHA SEROW250, YAMAHA XT250X, YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA Bolt RSpecifications, YAMAHA MT-03
Can also be installed on X FORCE.
Although not listed in the list of compatible vehicles, it can be installed on the X FORCE.
The installation itself takes less than a minute, but it is Large strange to get to the Coupler where it is installed.
The desired Coupler cannot be reached unless all the Covers around the Front are removed.
Same location as CYGNUS Griffus.
Two things to note after installation.
Both are basic, but we recommend checking them to avoid having to do it twice.
1.The coupler's detent (pawl) must hang firmly on the coupler of the vehicle's Both Sides.
2.The Engine must be able to start until the Side Stand is released.
In particular, in 1., if the Coupler is removed while driving, the Engine will stop immediately. (This is the same as when the Side Stand is turned on in a NORMAL car.)
View detail
Used in MONKEY125
Purchased to read MONKEY and other OBDData
I thought about making my own, but considering the time and effort required to assemble it with the right parts, it is better to purchase this one.
View detail
XG250 TRICKER Error Code Cancellation
While driving XG250 TRICKER, I was going to fix the Mirror, but I pushed the Kill switch by mistake. When I returned the Kill switch, the Motorcycle restarted without stopping, but the CheckLamp was turned on. I do not know the details, but it seems that when the Kill switch is pressed, the warning light comes on unless the key is turned off and then turned on again, or the Engine is started by turning the Cell. Once the light comes on, it is very annoying because the CheckLamp does not go out unless you reset it with OBD2. I used the 3-pin adapter, which is a KITACO product, so the work was completed without any problems. View detail
To erase fault codes
When I installed the Sub computer on my ZX14R, I accidentally turned the key to ON and the warning light came on. I purchased this product to turn off that warning light. I connected it to an Altia diagnostic machine and used UniversalMODE to diagnose the problem and was able to eliminate the fault code.
It is a little pricey, but I am happy with the time and Gold I will save compared to taking it to the Dealer.
View detail
Fits: YAMAHA Cygnus Gryphus, HONDA CRF1100L Africa Twin, HONDA CBR400R, HONDA 400X, HONDA Rebel300, HONDA CBR500R, HONDA CB500X, Others , SUZUKI DL1000 V-STROM1050, KAWASAKI NINJAZX-25R, KAWASAKI NINJA1000SX, HONDA REBEL250
MT-09 (21) for diagnostic purposes.
I got this for checking and erasing DTCs on my MT-09 (21).
I am using it connected to my ODB2 scanner.
This Adapter is not available for vehicles up to 20 years old because they have a white 4-pin connector.
View detail
Used for X-MAX
I was able to use it on my X-MAX250. When I posted this before, I mistakenly thought it was 4-pin, but it was 3-pin. I was able to use it without any problem when I put it on 3Pin again. View detail
I was able to use it on my MAJESTYs 155.
I was able to use the MAJESTYs155 (3Pin) without any problems and eliminate the error, but the X-MAX (4Pin) showed a communication error and could not be used. I was able to use it with MAJESTYs155 (3Pin) without any problem and erased the error, but with X-MAX (4Pin), a communication error was displayed and I could not use it. I'm not sure if it's because the car model is not compatible or the Cable is defective. I will try to use it with a different car model. View detail
Fits: YAMAHA CYGNUS Gryphus, YAMAHA Bolt, YAMAHA GEAR, YAMAHA XG250 TRICKER, YAMAHA SEROW250, YAMAHA XT250X, YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA Bolt RSpecifications, YAMAHA MT-03
SEROW250 Side stands switchCancellation
When driving on a rough forest road, the Side Stand would sometimes shake and move, causing the engine to stop. I was thinking of modifying the wiring and canceling the stand switch myself, but I found an inexpensive and convenient product on sale from KITAKO! I think I can drive on the forest road without stress now. View detail
I was able to get the Data properly.
Purchased to get vehicle data from OBD2.
I took Data with OBDScanner, but it shows well.
If Cable was a little longer, it would be even better.
I would have had no complaints if the price had been around $2,500.
View detail
Purchased for use with the XSR900
Whenever I get an error of any kind, I have to take it to a motorcycle shop to turn it off.
I had to bring it in and have it removed every time the ABS error kept coming up even when the Tire was idling.
View detail
clearance goods
I bought it to erase the error display of Injection
Each manufacturer, starting with the 17MODEL, is able to perform vehicle diagnostics through an OBD connection so I wonder if there are people who are going to need it in the future?
I plugged myself into the Universal diagnostics, read the error code, erased the Fault, and then used I did
Each Manufacturer comes with a pre-machined Connector, so when you connect, you can use it to connect to the You won't have any doubts about this
The Large Hand Manufacturer is putting out gap products like this one, and it's very I appreciate it
View detail