Reviews
I hear it breaks down a lot. 。 Looks like it's been taken care of.
Wiring has been removed from the mounting of the switch.
I tried to do it because others were consolidating ahead of me, but it was a little different, as if they had taken measures.
I hope it doesn't get torn off.
View detail
All Screw arrived instead of half Screw.
I ordered a 65mm to install a radial mount caliper, but received an All Screw instead of a half Screw.
When I bought the 75mm before, it was semi-screw, but, I didn't use it for Caliper installation.
View detail
Third generation RepairSwitch
This is the third RepairSwitch.
Wiring breaks from the root in approximately 3-year cycles.
The switch itself is fine, but the inside of the base itself is thin and fragile due to its small size, the switch body is fixed and the harness on the body side is free, but over the years vibration and other factors have caused the stress to build up and cause a pop-drill.
It can also be folded without leaks even when secured with Tie Wrap.
I was getting tired of all this, so I solidified the Body and Wiring with a GRU-Gun and shrink tubing.
In the meantime, I have been using only the GRU-Gun to connect and heal the last broken Switch with the Solder, and it is looking good.
View detail
KOHKEN KOHKEN Roller Type Micro Switch
MechanicalClutch from KOKENN Avanza." I purchased this product because I accidentally damaged the Switch that came with the
The angle of the Roller was slightly different from the Switch that came with Avanza.
The Roller Bracket was straight on the one I received, even though it was slightly bent in the sample photo.
It is not impossible to use it as it is, but if the Roller is bent a little like the Switch that came with Avanza, it can be used with Avanza without any problem.
When a terminal broke off, I was a bit frazzled, but Aftermarket parts were solid and reassured me.
View detail
Repair Parts
Tie Wrap together the Wiring from Switch and it will break in the near future.
The original Switch was just discarded in anger.
This Repair Parts did not include Bolt, as expected, but Bullet Terminal was included, thank goodness!
I headed to my neighborhood Home center to buy Bolt!
Size is 2mm and I bought the length 10mm.
Washer and Nut also Quantities:Set and it is 5Quantity:It contains about a set and costs 200 yen. I don't think I will be using it in the future, but I put it away in the "Large" case.
What I'm trying to say is don't throw Bolt away!
View detail
Awww, that's too expensive.
I put the cord together with Tie Wrap and when I found out, the terminal was broken from the root, so I decided to buy Spare immediately, which was about 1,000 yen. But then I saw the price and I was surprised! It seemed ridiculous, so I bought the micro switch with the terminal for solder. Probably because it is a terminal for a weak Print board, it might have broken due to lack of strength.
Maybe this is supposed to be a countermeasure, but it's still expensive!
View detail
Beautiful enough to be convinced even if it is told that it is Titanium
【What made you decide the purchase?】
I bought it for brembo's Monoblock caliper already mounted on MT-09.
Because the Caliper bolt of MT - 09 Standard is rusty, I ordered OEMCaliper bolt for YZF - R1 two generations ago and used it. Although it is Bolt for SS, it certainly is hard to rust and it is a high quality finish, but I thought that it looks too odd in combination with Brembo caliper because it looked like OEM so much, - I was looking for a thing of the finish.
Though it was a thing of Titanium that I found right away, I found Kolken 's Bolt in a place I was hesitant thinking about how to put out more than 20,000 yen for 4 Bolt in a fossil stone, and I immediately purchased it It was.
【How was it actually used?】
For amateurs it will cost more than 10,000 yen Material : It is about beauty that it is convinced even if it is told that it is Titanium.
Because it is Bolt of the Taper shape despite its plainness, it is full of Custom feeling, polite surface finish. It is full of luxurious feeling that I can not think of Stainless Steel.
By the way, things purchased will be 70 mm below the head. I adjusted it to the length of Bolt of R-1 that I used until that time. MT-09 OEM's Bolt is a few millimeters short, but there is no problem with mounting. Of course MT-09 bremboMonoblock (5 mm Spacer biting) Even a combination of them is no problem as shown in the picture.
【Mounting was difficult?】
I asked Motorcycle store to wear it by asking for vehicle inspection and maintenance.
In OEM Caliper fixed use, I think that it is good to tighten by following the specified Torque, but if you have a Caliper outside the company like my Motorcycle, the designated Torque may be different from OEM, I think that it is better for you to ask PRO if you are uneasy.
【Please tell me the installation point and hang】
When installing with Caliper's fixed, let's abide by the designated Torque for parts that are life-threatening.
Moreover, since I think that Bracket part is Large half in case of Aluminum, when using Bolt of Stainless Steel, I think that it is safer to apply Thread compound to prevent contact corrosion of dissimilar Gold group.
[Is there anything I was disappointed about?]
None
【Hope for Manufacturer - Please let me know if you have any improvement points]
None
【Have you compared items?】
- βTITANIUM Front caliper Mount BoltKit
When you get lost, you can make a mistake if you buy this. Because of the highest grade Bolt saying there would not be any more, I bought the budget Over this time I bought it off.
[Others]
To be honest, I think that it is a genuine and inconspicuous custom parts. But customizing it with hanghang saying that says this is saying that one and only wonderful custom machine will be finished.
View detail
Material : Even Stainless Steel is enough!
It is a price that Titanium can also be bought from price, but is it Titanium's 55? (1098 Standalone is 60?) I could not find it and purchased it without any help. However, the finish is wonderful, I felt Stainless Steel was enough. View detail