Reviews
Fits: HONDA DAX125, HONDA MONKEY125
Is it essential in modern times?
Good product
When you live a life where your phone is indispensable, battery is always a concern.
The USB port gives me a sense of security.
If you read the Instruction Manual carefully, I think it is gentle as a work S-Kill.
However, it is necessary to pay attention to the removal and installation of the light cover (plating parts) and the fit of the wiring.
View detail
DL1000 V-STROM800 used for power extraction under Seat
The DL1000 V-STROM800 has an OEMOption to install a 12VCigar lighter socket under the Rear Sets. The Attachment power supply Wiring for this purpose comes to the position shown in the photo. If you use KIJIMA's ACC Branch Harness that you purchased, you can get the power supply in Couplet-on. However, please note that the +- terminals are reversed, so the terminals need to be replaced. This is recommended for those who do not want to damage the existing Wiring. View detail
ITType." What does that mean, Italy?
I wanted to change to a Tail lamp with an integrated License Plate Light. I could have chosen anything, but since the car I was installing it on is an old ItalianRacer, I looked for a design that would not ruin the atmosphere and decided on this one.
I think KIJIMA is the best because the valve is sold separately, but it is a product of a well-known manufacturer, inexpensive, and easily available, and KIJIMA also supplies small repair parts such as lenses and rubber base parts. KIJIMA and Tail lamps are strong for classic vehicles.
Personally, I am disappointed only in the Fixing Screw, which is too small, and the Nut and Washer are too small to work with, and the originally drilled holes are too large in diameter. If you are going to drill a hole in a cowl, I don't think M3 or M5 will make any difference.
The base of the Rubber has a fairly solid thickness, and these points are very favorable.
Although there are only three wings, a WiringMemo is included, and it is also designed with the beginner in mind.
View detail
inconspicuous
I was a bit surprised at the price for such a bracket, but considering the time and effort required to find a substitute and the fit, it may be inexpensive.
The method of installation is up to you.
View detail
Fits: HONDA DAX125, HONDA MONKEY125
Room for improvement
This set comes with a connector to avoid cutting cables. Unfortunately my 2023 monkey did not have the connector in the pictures nor anything remotely resembling the connector layout. Had to cut cables, sadly. I managed to slightly round one of the handblebar bracket bolts from the set while tightening.. with a small ratchet. The bracket itself and the USB connector are nicely made. Back light is green. The cap seals nicely and gives confidence in water resistence. Manual is japanese. View detail
There is a sense of security dedicated to the car model.
DL1000 V-STROM650XT ('22) The product has been installed in a
It will be used in conjunction with Hepco&Becker's Engine Guard,
The bracket of the Radiator part was a little bit hit by the Guard,
The installation was only a little difficult, but it was almost interference-free. I think there may be individual differences, so this is just for reference.
Because the connection between the Fog Lamp and the included Harness was a Flat Terminal,
We changed to WaterproofCoupler just in case.
The brightness is sufficient for an auxiliary light,
Cutline is also solid, so I don't think it will bother oncoming traffic.
Considering the price, the texture might be a bit lacking,
If you are concerned about this, you should consider another product.
View detail
A quality low-profile blinker kit
The kit I purchased was well packaged and tailored for installation on a V-Strom 650. All parts appear to be good quality and ready for immediate installation on the bike. The kit includes wiring adapters to suit the bike (bullet connector to 2-pin Suzuki connector) and a new 7-pin LED blinker relay. Installation was easy for someone with moderate experience. Tools required: open-end wrenches (8~12mm), hex key wrenches (4~5mm), 10~12mm socket. The rear fender of the bike must be removed to access the wiring and remove the existing blinkers. Routing the wiring through the adapter plates, washer and nut requires patience and a delicate touch. Aside from that, it's a matter of securing connections with electrical tape and securing the wiring to the frame. The kit is quite bright and very visible, even during the daytime. The blinkers are all mounted on flexible stalks, so they should survive if the bike is dropped. Overall, I am very pleased with the purchase. View detail
Fits: HONDA CT125 CT110 HUNTER CUB, HONDA CT125 CT110 HUNTER CUB
Durability may be difficult.
The ease of installation was a plus.
The battery stopped charging less than six months after installation.
According to Manufacturer, it was due to age and not covered by warranty.
I hoped it would be a little sturdier and last longer.
View detail
Rare Other Brand Product for 6v
This is a Horn for 6V electrical equipment, which is now rare.
Since most of the vehicles have been manufactured for a long time, we recommend replacing them with OEM replacements.
View detail
Fits: SUZUKI GSX-S125, SUZUKI GIXXER 250, SUZUKI GIXXER SF250, SUZUKI GSX-R125, SUZUKI GIXXER 150, SUZUKI V-Strom250 SX
Extension Harness Min.
Quantity of 1 Set for 1 Vehicle to install TRL2Blinker:Set.
TRL2 LED Blinker*4
Mount for TRL2*4
Extension Harness (long)*2
Extension Harness (short)*2
MicroIC Blinker Relay*1
Small and very Stylish
The mounting is done by sandwiching the Mount with the Plate, and since the hole is small, the Bullet Type Terminal is inserted while shifting it slightly.
The price is almost the same if you buy them individually, but you save money for the Extension Harness.
The included MicroIC Blinker Relay is about the size of a small finger, so you should have no trouble finding a place to place it, but the terminals are bare, so be careful not to touch the Gold Genus.
View detail
Flashing relay
GSX-1000 L3 is installed.
Since Relay is in the Blue circle, it is easier to Rose Seat Cowl as much as possible, and since Relay itself has a protrusion to prevent it from falling out, Space is needed to knead it lightly with Minusetc.
Things are OEM same etc. and not so good or not so good.
View detail
It's best
Installation is so easy.
Just unplug the headlight and connect it to the blue service wire.
It fits perfectly with the Hunter Curve and has a good sense of unity.
The only downside is that it is not waterproof when it rains.
You need to quickly unplug the USB and close the lid.
It would be even more perfect if it was supplemented to make it waterproof even with USB installed.
thank you -------------------------------------------------- -------- Installation is so easy. Just unplug the headlight and connect it to the blue service wire. It fits perfectly with the Hunter Curve and has a good sense of unity. The only downside is that it is not waterproof when it rains. You need to quickly unplug the USB and close the lid. I think it would be even more perfect if it was supplemented to make it waterproof even when USB is installed. thank you Powered by Google Translator
View detail
Kijima ACC branch harness kit
I haven't installed it yet, but it's good because the quality of the product and the product are excellent. I'll use it well. Thank you for the meticulous packaging and sending. View detail
Very happy with purchase
Bought this as a north American buyer, received the item 4 days later, perfect packaging. The light diameter is the same as the OEM on the Yamaha XSR900. Very please with the quality of the product. View detail
I am satisfied
Degrease the body side and the back of the rim, and use the supplied double-sided tape.
Just paste three places.
I'm a little concerned about adhesion because of the cold weather.
Warm it up with a heat gun, etc., and then use masking tape.
It would be good to hold it down and take a curing period.
The two holes were placed down.
Originally, the current OEMLight shines because the Rim is transparent.
I don't know exactly what the difference is, but I've been using Plating for the other Parts.
I am personally satisfied because I want to unify the two.
It is easier to understand than the Blinker Rim.
View detail
I am satisfied
Degrease the body side and the back of the rim, and use the supplied double-sided tape.
Was it four places? Just stick it on.
Like Headlight, I am a little concerned about the adhesive strength.
I would warm it up and cure it with Tape or change the Double-sided Tape.
The fitting was good and I am satisfied with the product itself.
View detail
I can't install it on my bike jb03
The quality is well made It's jb03 about the feeling of use, and I bought it after seeing it installed on YouTube, but I couldn't find it Cost performance and comparison to other products Kitako products are easy to distribute, but the headlights may not close Delivery and packaging to WeBike in a week The packaging is great Concerns when purchasing Please check the jack and purchase it. I looked all over the line but couldn't see it View detail
Particularly good for places where there is a lot of ROSS
Reusable Tie Wrap for easy removal.
It is especially effective for parts that are frequently removed and attached. It is a little thicker than regular tie wrap, so be careful, but I use it to tie parts that are often removed when disassembling.
Off-road motorcycles are especially used for this purpose.
The thicker the wire, the sturdier it is, so there is no need to worry too much. However, if you cut the extra length, you can only use the same length or a shorter portion.
View detail
The ability to release as intended is still an advantage.
Vehicles used in Races and competitions are often cleared.
If Tie Wrap can be Released in such cases, it can be used once more.
This is important.
But it's not cosmetic. Definitely.
But they are SDGs. Because they can be reused.
Even if you are not a "good" person, you don't have to use a nipper to cut it, so you don't have to choose a place for it. It is surprisingly possible even in a gap where tools cannot fit.
View detail
It was worth the price.
I was a little disappointed because it was an Image that glowed a little brighter.
Well, I can barely see Meter, so I'm going to use it as is for now.
View detail