KOSO Motorcycle Electrical Reviews

Filter

Write a review and get Webike Points!

Reviews

KOSO Electrical Clear all

[Rough Craft ION] Ultra-Small LED Blinkers

KOSO

18 Sep 2023

KOSO T&T Multi Function Meter [Black Panel]

Japanese Webike user

4/5

Cospa is good

I want to refreshing the handlebar area, but I don't want to give up my Portable navigator because it is so useful. I decided to replace the Meter to solve this problem, and I fantasized about Stack's ST500, but the price was not realistic for me, so I considered KOSO or acewell and decided to go with Design and It's broken We chose this product from KOSO, where there was no such thing as a "no".
For the installation, we wanted to add an additional indicator, so we cut a frame for the Multimeter out of 1.5mm thick aluminum plate and installed it on a base made of the bracket of the OEMMeter and the bracket and high nut we purchased at Home center. The wiring is a 9-pole and 3-pole 110 type coupler that can be attached and detached with the coupler just like the OEMMeter. The wiring was made by purchasing a 9-pole and a 3-pole 110 coupler to create an intermediate harness.
I installed a Bullet Terminal on the MultimeterBody wiring and connected it to the intermediate harness, relying on the wiring diagram in the Instruction Manual and Service Manual, and found that the speed signal and ACC wiring were redundant on the 9-pole side. I am not sure. I am not sure, but I heard that in case of ZRX1100 with OEMIgniterSpec. the engine will not blow more than a certain degree if the speed signal is not connected after the limiter is cut. My vehicle was replaced with a Unit from Uotani, so even with the extra wire for the speed signal, it seems to be Large sturdy. As for the permanent power supply, I connected a branch from the coupler of Ignition, and was able to energize Multimeter without any problem. In addition, since Multimeter had only one warning light for oil pressure warning light and water temperature warning light, we set up a separate Indicator light and connected it to Multimeter. I also added a separate indicator light for the high beam indicator. Also, for the Blinker and Neutral indicators, I added an Indicator light on top of the Meter, because the Indicator in the Multimeter alone seemed too small to be easily visible.
Finally, the speed sensor was attached to the Rear Sprocket by bonding a magnet to it, since it was difficult to attach the Speed sensor to the Front with the provided Bracket.
After confirming that the device was working, we set it up according to the Instruction Manual and adjusted the speed setting by comparing it to the speed on the GPSSpeedometer app on our smartphone while driving around the neighborhood, and we were ready to use the device.
Since we were unable to gather detailed information on the replacement of the Meter, we took a leap of faith that we could probably get by with it. However, the Instruction Manual did not include a EGCheckLamp." The design is to my liking, the texture is not bad, the operation of the Tachometer is smooth, the visibility of Speed is good, and for the price of about 20,000 yen, I think this quality is a good buy! The installation could be improved a little more. I would like to think about the installation of the handlebar in the future, as I think it needs a little more improvement. This time, I am very satisfied with the Refreshing around the Handlebar as expected. It was a fun summer vacation craft. View detail

Sequential LED Blinker 3 [Vehicle Inspection Compliant] Light Smoke [GW-02] Left/Right Set

KOSO

26 Feb 2022

SONIC LED Sequential Blinker & Position

Fits: その他

Japanese Webike user

3/5

Universal, yet the Type 3 Grom doesn't work when pimped.

It was a Type 3 Grom, so it might have been like Title, but it could be a possible problem. By the way, Blinker and Position are separate LEDs. I'm not sure if it's a problem or not, but I'm not sure if it's a problem or not. So I asked the motorcycle shop to copy the wiring diagram and looked at it. First, I used the rectifier.
Countermeasures?
Add a 6ADiode between both BlinkerWiring and ConnectorWiring.
In addition, the position was extended from the license lamp on the rear and connected, and this extension was large. At this time, in consideration of later, I passed two wires for Earth and two wires for Position.:It is a connection with the License Wiring that has been extended from 2pc to 1pc.
Result?
When I started the engine and started the blinker, it flowed, but it was unstable, coming on and off.
Countermeasures?
No more Blinker around. (Inside Headlight) I heard that it is difficult to add diodes to the 3PHarness. So I went to Mr. Takekawa's place and found a 3PHarness for Honda with universal diodes, which was expensive but I bought it. I used this only for BlinkerWiring.
Result?
Naturally? The result was the same as the previous one.
Countermeasure? This is a countermeasure? Implement immediately after
If this happens, I will add a diode to Blinker's Grounding Wire.
This uses the remaining 1 pc from the extension of Position. The connection was treated in the same way as Position.
Result?
I'm not sure if this is a good idea or not, but I think it's a good idea.
operation
WhitePosition, always on
Blinker, the other side of the stream is still lit up.
Blinker position, always on
I think the light intensity is bright. The light intensity is bright.
As for durability, I think the LED is large and durable, but we'll see.
General review
I chose this blinker because the position will be lost when I install the switch assembly with Hazard later. I'm sure the size and construction is solid. The base is rubber type to prevent vibration.
I'm not sure if it's a test or not. I'm not sure if I'd recommend it, but I'm personally satisfied with it. I'm not sure if I'd recommend it, but I'm personally satisfied. (Maybe because it worked fine.)
I also wish there was a Smoked lens in the lineup. View detail