Reviews
Fits: HONDA DAX125, HONDA MONKEY125
Room for improvement
This set comes with a connector to avoid cutting cables. Unfortunately my 2023 monkey did not have the connector in the pictures nor anything remotely resembling the connector layout. Had to cut cables, sadly. I managed to slightly round one of the handblebar bracket bolts from the set while tightening.. with a small ratchet. The bracket itself and the USB connector are nicely made. Back light is green. The cap seals nicely and gives confidence in water resistence. Manual is japanese. View detail
A quality low-profile blinker kit
The kit I purchased was well packaged and tailored for installation on a V-Strom 650. All parts appear to be good quality and ready for immediate installation on the bike. The kit includes wiring adapters to suit the bike (bullet connector to 2-pin Suzuki connector) and a new 7-pin LED blinker relay. Installation was easy for someone with moderate experience. Tools required: open-end wrenches (8~12mm), hex key wrenches (4~5mm), 10~12mm socket. The rear fender of the bike must be removed to access the wiring and remove the existing blinkers. Routing the wiring through the adapter plates, washer and nut requires patience and a delicate touch. Aside from that, it's a matter of securing connections with electrical tape and securing the wiring to the frame. The kit is quite bright and very visible, even during the daytime. The blinkers are all mounted on flexible stalks, so they should survive if the bike is dropped. Overall, I am very pleased with the purchase. View detail
There is a sense of security dedicated to the car model.
DL1000 V-STROM650XT ('22) The product has been installed in a
It will be used in conjunction with Hepco&Becker's Engine Guard,
The bracket of the Radiator part was a little bit hit by the Guard,
The installation was only a little difficult, but it was almost interference-free. I think there may be individual differences, so this is just for reference.
Because the connection between the Fog Lamp and the included Harness was a Flat Terminal,
We changed to WaterproofCoupler just in case.
The brightness is sufficient for an auxiliary light,
Cutline is also solid, so I don't think it will bother oncoming traffic.
Considering the price, the texture might be a bit lacking,
If you are concerned about this, you should consider another product.
View detail
Fits: HONDA CT125 CT110 HUNTER CUB, HONDA CT125 CT110 HUNTER CUB
Durability may be difficult.
The ease of installation was a plus.
The battery stopped charging less than six months after installation.
According to Manufacturer, it was due to age and not covered by warranty.
I hoped it would be a little sturdier and last longer.
View detail
Rare Other Brand Product for 6v
This is a Horn for 6V electrical equipment, which is now rare.
Since most of the vehicles have been manufactured for a long time, we recommend replacing them with OEM replacements.
View detail
Fits: SUZUKI GSX-S125, SUZUKI GIXXER 250, SUZUKI GIXXER SF250, SUZUKI GSX-R125, SUZUKI GIXXER 150, SUZUKI V-Strom250 SX
Extension Harness Min.
Quantity of 1 Set for 1 Vehicle to install TRL2Blinker:Set.
TRL2 LED Blinker*4
Mount for TRL2*4
Extension Harness (long)*2
Extension Harness (short)*2
MicroIC Blinker Relay*1
Small and very Stylish
The mounting is done by sandwiching the Mount with the Plate, and since the hole is small, the Bullet Type Terminal is inserted while shifting it slightly.
The price is almost the same if you buy them individually, but you save money for the Extension Harness.
The included MicroIC Blinker Relay is about the size of a small finger, so you should have no trouble finding a place to place it, but the terminals are bare, so be careful not to touch the Gold Genus.
View detail
Flashing relay
GSX-1000 L3 is installed.
Since Relay is in the Blue circle, it is easier to Rose Seat Cowl as much as possible, and since Relay itself has a protrusion to prevent it from falling out, Space is needed to knead it lightly with Minusetc.
Things are OEM same etc. and not so good or not so good.
View detail
It's best
Installation is so easy.
Just unplug the headlight and connect it to the blue service wire.
It fits perfectly with the Hunter Curve and has a good sense of unity.
The only downside is that it is not waterproof when it rains.
You need to quickly unplug the USB and close the lid.
It would be even more perfect if it was supplemented to make it waterproof even with USB installed.
thank you -------------------------------------------------- -------- Installation is so easy. Just unplug the headlight and connect it to the blue service wire. It fits perfectly with the Hunter Curve and has a good sense of unity. The only downside is that it is not waterproof when it rains. You need to quickly unplug the USB and close the lid. I think it would be even more perfect if it was supplemented to make it waterproof even when USB is installed. thank you Powered by Google Translator
View detail
Kijima ACC branch harness kit
I haven't installed it yet, but it's good because the quality of the product and the product are excellent. I'll use it well. Thank you for the meticulous packaging and sending. View detail
Very happy with purchase
Bought this as a north American buyer, received the item 4 days later, perfect packaging. The light diameter is the same as the OEM on the Yamaha XSR900. Very please with the quality of the product. View detail
I am satisfied
Degrease the body side and the back of the rim, and use the supplied double-sided tape.
Just paste three places.
I'm a little concerned about adhesion because of the cold weather.
Warm it up with a heat gun, etc., and then use masking tape.
It would be good to hold it down and take a curing period.
The two holes were placed down.
Originally, the current OEMLight shines because the Rim is transparent.
I don't know exactly what the difference is, but I've been using Plating for the other Parts.
I am personally satisfied because I want to unify the two.
It is easier to understand than the Blinker Rim.
View detail
I am satisfied
Degrease the body side and the back of the rim, and use the supplied double-sided tape.
Was it four places? Just stick it on.
Like Headlight, I am a little concerned about the adhesive strength.
I would warm it up and cure it with Tape or change the Double-sided Tape.
The fitting was good and I am satisfied with the product itself.
View detail
I can't install it on my bike jb03
The quality is well made It's jb03 about the feeling of use, and I bought it after seeing it installed on YouTube, but I couldn't find it Cost performance and comparison to other products Kitako products are easy to distribute, but the headlights may not close Delivery and packaging to WeBike in a week The packaging is great Concerns when purchasing Please check the jack and purchase it. I looked all over the line but couldn't see it View detail
Particularly good for places where there is a lot of ROSS
Reusable Tie Wrap for easy removal.
It is especially effective for parts that are frequently removed and attached. It is a little thicker than regular tie wrap, so be careful, but I use it to tie parts that are often removed when disassembling.
Off-road motorcycles are especially used for this purpose.
The thicker the wire, the sturdier it is, so there is no need to worry too much. However, if you cut the extra length, you can only use the same length or a shorter portion.
View detail
The ability to release as intended is still an advantage.
Vehicles used in Races and competitions are often cleared.
If Tie Wrap can be Released in such cases, it can be used once more.
This is important.
But it's not cosmetic. Definitely.
But they are SDGs. Because they can be reused.
Even if you are not a "good" person, you don't have to use a nipper to cut it, so you don't have to choose a place for it. It is surprisingly possible even in a gap where tools cannot fit.
View detail
It was worth the price.
I was a little disappointed because it was an Image that glowed a little brighter.
Well, I can barely see Meter, so I'm going to use it as is for now.
View detail
Slim impression
I purchased these to install on my 2014 S1000RR.
The second model has been replaced by a narrow LED blinker, which is also attractive in its own right, but we wanted to make the most of the SS design, so we decided on this less conspicuous product.
The installation itself is completed only with Torque and +Screw.
Instruction is also clear and Quantity:Pair (for Left and Right) There is also an indication so you will not make a mistake.
However, since it is LED, high flasher will occur. I don't mind it that much, but those who care about it may be bothered.
Well, when you are on it, you can't see it because it is a very Compact Blinker.
Note that the Crimp on the Connector and wire may be a little weak and may come loose. Be careful when attaching and detaching.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R SE, KAWASAKI NINJA2 Helmet50R EX250P
I don't want to hurt OEMHarness.
I want to use CouplerON as much as possible, because cutting OEM harnesses is a source of trouble.
Considering the price and construction, this is a very expensive product, but the advantage is that it does not damage the OEM's harness.
Installation is easy. In the case of the Ninja ZX-25R, remove the DummyCoupler and insert this product into the DummyCoupler.
The original DummyCoupler is simply attached to the Coupler on the other side of this product.
After installation, an energization test was also conducted.
Checked with Tester and no problem.
View detail
Fits: HONDA SUPER CUB 50PRO, HONDA SUPER CUB 50, HONDA CROSS CUB50, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA CROSSCUB110, HONDA SUPER CUB110, HONDA CROSSCUB110
Does not fit 23 year old JA56 products
I ordered several parts from We Bike and installed the ones that fit.
Surprisingly, there are too many incompatible parts.
It does not fit the JA56 model, which is an officially imported product from Korea.
Machining is required when installing. Please keep this in mind when purchasing from Korea.
-------------------------------------------------- -------- We are ordered by ordering various parts from Webike, but there are too many parts that are unexpectedly compatible. It is not suitable for the JA56 model, the official imported product of Korea. When mounted, processing is required. Please refer to the purchase of Koreans. Powered by Google Translator
View detail
Sense of security.
If you are looking for a Square type, this is the one you should choose.
I personally think that this is the best choice in terms of tightness, design, and quality. I can feel that each item has been inspected one by one, which gives me a sense of security.
I am very happy with the Large size.
View detail